MAULmakro 826 36 LED Magnifying Lamp

Product Identification

Product Name: MAULmakro 826 36

Brand: MAUL

Article Numbers:

• Main Unit: 8263609.160A
• LED Ring: 8263309.200
• Driver Board: 8263309.210

The lamp operates on 230V power.

Visual Description: The MAULmakro 826 36 is a white, articulated arm magnifying lamp with an LED light ring. It includes a power cord with a standard plug.

Component Visuals:

• LED Ring (Art.-No.: 8263309.200): A circular LED module, shown in two parts in one image, with a connector cable.
• Driver Board (Art.-No.: 8263309.210): A printed circuit board with electronic components, including capacitors, resistors, and a transformer, with screw terminals for wire connections.

Safety Warnings

Important Safety Notice: The magnifying lens must be protected from direct sunlight. Exposure to sunlight through the lens can concentrate light and cause a fire hazard.

This warning is provided in multiple languages:

• German: Lupe gegen Sonneneinstrahlung abdecken. Brandgefahr!
• English: Lens must be protected from sun beams. Danger of fire!
• French: Protégez la loupe contre les radiations solaires. Danger d'incendie!
• Russian: Лупу закрывать от солнечного излучения. Опастность возникновения пожара!

General Usage Icon: An icon depicts a person reading under a light source, suggesting safe usage.

Component Replacement Instructions

The following steps detail the process for replacing the LED ring and the driver board.

Step 1: Accessing the Lamp Head Components

Tools Required: PH2 screwdriver.

Procedure:

1. Locate the screws securing the lamp head cover. On the first page of the steps, five screws are indicated with red circles around them on the outer casing of the lamp head.
2. Using the PH2 screwdriver, remove these screws.
3. Carefully separate the lamp head casing to expose the internal components.

Visual Description of Opened Casing: After removing the screws, the lamp head casing can be opened, revealing the internal structure, including the LED ring and the driver board.

Step 2: Replacing the LED Ring

Tools Required: PH2 screwdriver, PH0 screwdriver.

Procedure:

1. Identify the screws holding the LED ring in place. The image on page 5 shows red circles around two screws near the LED ring and blue circles around two connection points.
2. Use the appropriate screwdrivers (PH2 for some screws, PH0 for others as indicated by the circles) to remove the screws securing the LED ring.
3. Disconnect the LED ring's power connector. The image on page 5 indicates a connector labeled "ZIEHEN PULL b)" for disconnection.
4. Remove the old LED ring.
5. Install the new LED ring (Art.-No.: 8263309.200), ensuring it is correctly seated.
6. Reconnect the power connector.
7. Reassemble the lamp head casing, securing it with the screws removed in Step 1.

Step 3: Replacing the Driver Board

Tools Required: PH0 screwdriver.

Procedure:

1. Locate the driver board within the lamp head. It is typically situated behind the LED ring assembly.
2. Identify the screws and wire connectors securing the driver board. The image on page 7 shows the driver board and highlights a connector labeled "ZIEHEN PULL b)".
3. Use the PH0 screwdriver to remove any screws holding the driver board in place.
4. Disconnect the wire connectors from the driver board. The connector labeled "ZIEHEN PULL b)" needs to be pulled to disconnect.
5. Remove the old driver board (Art.-No.: 8263309.210).
6. Install the new driver board, ensuring correct orientation.
7. Reconnect all wire connectors securely.
8. Reassemble the lamp head casing, securing it with the screws.

Note on Connectors: The instructions mention "DRÜCKEN PUSH a)" and "ZIEHEN PULL b)" which refer to specific types of connectors that require pushing to insert or pulling to release.