Paulmann 705.28, 705.29, 705.30 LED Strip Sets: Safety and Installation Guide

Safety Instructions and General Information

Please read these safety instructions carefully before installation and use. Retain them for future reference.

General Warnings:

• This product is intended for indoor use unless otherwise specified (e.g., IP44 rated accessories).
• Ensure all electrical connections are made by a qualified person or in accordance with local regulations.
• Do not operate the product if damaged.
• Avoid exposing the product to extreme temperatures or direct sunlight unless designed for it.

Key Symbols Explained:

• CE Mark: Conforms to relevant EU safety standards.
• UKCA Mark: Conforms to relevant UK safety standards.
• Energy Efficiency Labels (A++, A, G): Indicates the energy efficiency class of the light source.
• IP20 Rated: Protection against solid objects larger than 12.5mm, no water protection.
• IP44 Rated: Protection against solid objects larger than 1mm, protection against splashing water.
• [battery-symbol]: Indicates battery requirements or usage.
• [light-source-symbol]: Refers to the light source.
• [cut-here]: Indicates where the LED strip can be cut.
• [avoid-direct-sunlight]: Avoid direct sunlight.
• [operating-temperature]: Indicates operating temperature range.
• [correct]: Correct or approved action.
• [incorrect]: Incorrect or not approved action.
• [direction-arrow]: Indicates connection direction or flow.
• [connection-arrow]: Indicates connection point.
• [power-connection]: Electrical connection point.
• [disposal-instructions]: Indicates proper disposal.

Product Variants and Specifications

This product line includes different LED strip lengths and associated drivers:

For use in damp locations or outdoors, an IP44 rated water protection accessory (Art.-Nr.: 702.47) may be required.

Maximum Expansion: The LED strip system is expandable. Maximum total length for expansion is typically 4m or 5.5m depending on the driver and specific setup (refer to driver specifications).

Installation and Connection

Follow these steps for installation and connection:

Step 1: Connecting the Driver and LED Strip

Connect the LED strip to the appropriate driver. Ensure correct polarity (+/-) is maintained. The driver for 705.28 is 50VA, and for 705.29 is 75VA. The LED strip can be cut at designated points [cut-here] if a shorter length is required.

Step 2: Connecting the Controller (RGBW)

The RGBW controller allows for color and brightness adjustments. Connect the LED strip to the controller's output terminals (typically labeled R, G, B, W, or similar). Connect the controller's input to the driver.

Controller Terminals:

• Red Channel (R)
• Green Channel (G)
• Blue Channel (B)
• White Channel (W)
• +24V Power Input: From driver.

Step 3: Powering the System

Connect the driver to the mains power supply. The driver converts mains voltage to the low voltage required by the LED strip and controller.

Step 4: Remote Control Operation

The system includes a remote control for operating the LED strip. The remote typically requires a CR2025 3V Li-Ion Battery (150mAh) [battery-symbol].

Remote Control Functions:

• [power-on]: Turns the lights on or off.
• Brightness Adjustment: Use buttons (e.g., 100%, 75%, 50%, 25%) or a slider to adjust brightness.
• Color Selection: Select specific colors (Red, Green, Blue, White) or mix them.
• Dynamic Modes: Select preset lighting effects like "JUMP" (color changes) or "FADE" (smooth transitions). Options may include JUMP3, JUMP7, FADE7.
• Mode Speed/Sensitivity: Adjust the speed of dynamic modes or brightness levels.
• AUTO: Cycles through various modes.

Step 5: Expansion (Optional)

The LED strip system is designed to be expandable. Additional LED strips can be connected in series to extend the total length, up to the maximum supported length for the driver (e.g., maximum expansion length: 4m or maximum expansion length: 5.5m). Ensure all connections are secure and polarity is correct.

Installation Considerations:

• Minimum Bending Radius: Do not bend the LED strip tighter than a radius of 30mm [r ≥ 30mm].
• Minimum Distances: Maintain minimum distances as indicated in diagrams (e.g., maximum connection length: 5m, maximum connection distance: 7m).
• Angles: Ensure installation angles are appropriate (e.g., minimum angle: 60°).
• Operating Temperature: Operate within the specified temperature range [operating-temperature].

Replaceability and Disposal

Component Replaceability:

• End User Replaceable: The light source (1) or operating device (4) can be replaced by the end user without permanent damage to the luminaire.
• Qualified Electrician Replaceable: The light source (2) or operating device (5) can be replaced by a qualified electrician without permanent damage to the luminaire.
• Not Replaceable: The light source (3) or operating device (6) is not replaceable; the entire luminaire must be replaced.

Disposal:

Old electrical equipment (Altgeräte) must not be disposed of with household waste. They can be returned to public collection points [disposal-instructions]. Batteries and rechargeable batteries, as well as lamps that can be removed without damage, must be separated from the old equipment before disposal. Consumers are responsible for deleting personal data on old devices. Please follow local WEEE (Waste Electrical and Electronic Equipment) regulations.

Energy Efficiency: This product contains a light source of energy efficiency class .