2022 Owner's Manual
A subsidiary of Thor Industries, Inc.
0230295.2022
Table of Contents
Section 1: Warranty & Service
Factory Tours Options and Equipment Dealer Responsibility Customer Relations Obtaining Emergency Warranty Repair To Contact Us About This Manual Warranty Packet Chassis Guide Safety Alerts Reporting Safety Defects Customer Responsibility Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Faciity Parts and Accessories
Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Fire Safety Fire Extinguisher Smoke Alarm Combination Carbon Monoxide /Propane Alarm Formaldehyde Extended Or Full Time Usage Cold Weather Usage Condensation
Section 3: Pre-Travel Information Vehicle Labels
Weight Terms Weight and Capacity Labels Loading Your Motor Home Trailer Plug Weighing Your Motor Home
Section 4: Vehicle Operation Vehicle Operation
Braking and Stopping Parking Brake Using The Rear Hitch Power Entrance Step Entrance Door Driver and Passenger Seat Seat Belts Child Safety Restraint Systems Vehicle Dash Outside Rearview Mirrors Power Remote Mirrors (if so equipped)
Remote Mirror Control / Mirror Heat Control
Rear Vision Camera Campsite Hook-Up Hydraulic Leveling System
2 2 2 2 3 4 5 5 5 5 6 7 7 8 8 8 9
17 18 18 19 20 24 24 24 25
27 27 27 29 29 30
33 33 33 34 35 35 36 37 37 38 38 38
39 39 40
2022 Jayco Precept
Table of Contents
Operating the Leveling System
41
Manual Operation
42
Hydraulic Control Panel
Helpful Hints
43
Panel Indicator LED
43
Emergency Stopping
44
Emergency Towing
44
Front Axle Tire Alignment
44
Wheel Lug Nuts/Wheel Liners
45
Tires
46
Changing A Tire
48
Awnings (if so equipped)
48
Awning Care
48
Electric Patio Awning with Remote Control
49
In Motion Detector (if so equipped)
49
Power Awnings (if so equipped)
49
Maintaining the Awning
50
Section 5: Slideout Systems
Electric Slide Room(s) (if so equipped)
53
General Slideout Operation
53
General Slideout Troubleshooting Checklist
54
Flush Floor Slideout
54
Schwintek In-Wall Slideout System
56
Norco Slideout System
59
Power Gear Slideout System
60
Fig.1 Slideout Controller
Power Gear Slim Rack Slideout System
62
Power Gear Ram Slideout System
66
Section 6: Electrical System
The Electrical System
69
In Case Of An Electrical Fire
69
Controls and Switches
70
Command Center
70
Command Center Panel
Command Center Panel w/Switch Modules
Testing The Campsite Power Connection
71
Connecting the Power Cord
71
Inverter (if so equipped)
72
Power Converter
74
Converter w/Charge Wizard (if so equipped)
75
12-volt DC System
76
12-Volt Fuse Panel
76
Replacing a Fuse
76
12-Volt DC Outlet
76
Batteries
77
House Batteries
77
Dry Camping
77
Battery Replacement
78
12-Volt Battery Disconnect
78
Battery Isolator Solenoid (if so equipped)
78
Battery Isolation Manager (if so equipped)
79
Auxiliary Start System (if so equipped)
79
Load Center
79
Automatic Transfer Switch (ATS)
80
Table of Contents
120-Volt Circuit Breakers
80
Replacement
80
Maintenance
81
Approximate Electrical Load Ratings
82
120-Volt 50 AMP AC Electric System (if so equipped)
83
50 amp Power Cord
83
Generator
84
Before Starting the Generator
84
Calculating 50 amp Electrical Load (if so equipped)
84
Maintenance
85
Starting the Generator
86
AGS (Automatic Generator Start)
86
AGS Controller
86
Command Center Panel
AGS Controller
Solar Prep (if so equipped)
87
Replacing Light Bulbs
87
Section 7: Fuel System
Fuel Safety
89
Exhaust Gas Fumes
90
Propane Gas System (if so equipped)
90
Propane Gas Container
91
Servicing or Filling
92
LP Gas Container Overfill
92
Propane Regulator
92
Propane Use and Safety
93
Using the Propane System
94
Cooking With Propane Gas
94
Calculating Propane Gas Usage
95
Traveling With Propane
95
Section 8: Plumbing System
Plumbing System
97
Plumbing System Maintenance
97
Monitor Panel
97
Monitor Panel
Command Center
Fresh Water System
99
Water Pressure Regulator (customer supplied)
99
Water Purification System (if so equipped)
100
Filter Housing
12-volt Water Pump and Switch
100
Draining The Fresh Water System
101
Exterior Fresh Water Drain
Uni-Dock Utility Center
102
Low Point Drains
Winterize with Air Pressure
109
Winterize with Antifreeze Method
111
Winterize the Macerator System (if so equipped)
112
Water Heater
113
Water Heater Switch (if so equipped)
114
Water Heater Bypass
114
High Altitude Deration
114
Pressure and Temperature Relief Valve
114
Draining and Winterization
115
Table of Contents
Outside Shower and Courtesy Light
115
Faucets
115
Bathroom Tub / Shower
116
Black/Grey Water System and Tanks
116
Black and Grey Tank Drains
118
Black/Grey Tank Drain and Valves
Black Tank Flush (if so equipped)
119
Tank Heaters (if so equipped)
119
Toilet (if so equipped)
120
Section 9: Heating & Cooling
Air Conditioner
123
Power Roof Vent (if so equipped)
123
Furnace
124
Fireplace (if so equipped)
124
Section 10: Appliances
Microwave
125
Cooking Safety
125
Cooktops, Range and Oven (if so equipped)
126
Electric Drop-In Cooktops (if so equipped)
126
Gas Drop-In Cooktops (if so equipped)
127
Oven (if so equipped)
127
Range Hood (if so equipped)
127
Refrigerator
128
Washer/Dryer (if so equipped)
129
Water Heater See Plumbing Section
130
Section 11: Electronics
HDTV Antenna/Satellite System
131
Antenna Power Supply
Antenna Power Supply (if so equipped)
132
Satellite (if so equipped)
132
Exterior Entertainment Center (if so equipped)
132
Section 12: Interior
Cleaning The Interior
133
Décor Glass (if so equipped)
133
Furniture Upholstery
133
Sofa and Dinette
135
Hide-A-Bed Sofa or Sofa Sleeper
135
Jack Knife Sofa
135
Trifold Sofa
135
Dream Dinette Unlocked
Dream Dinette Locked
Booth Dinette (if so equipped)
136
Booth Dinette
136
Dream Dinette
136
Pantry or Hutch (if so equipped)
137
Countertops
137
Laminate Countertops (if so equipped)
137
Flooring
138
Carpet
138
Solid Surface Countertops (if so equipped)
138
Vinyl Flooring (if so equipped)
139
Ceramic Tile (if so equipped)
139
Ceiling Fabric
139
Table of Contents
Privacy Drape Installation
139
Bed Storage
140
Prop Rod (if so equipped)
140
Gas Struts (if so equipped)
141
Cab-Over Power Bunk Bed (if so equipped)
141
Bunk Beds and Bunk Ladders (if so equipped)
142
Bunk Ladders (if so equipped)
142
Section 13: Exterior
Cleaning The Exterior
145
Mud Flap
147
Exterior Roof and Sidewall Vents
147
Windows
147
Exterior Ladder (if so equipped)
148
Sealants
149
Section 14: Travel/Camping/Storage Checklists
Travel Checklist
151
Motor Home Storage
152
Section 15: Additional Information
Featured Components Quick Reference Chart
155
Vehicle Maintenance Record
157
Ownership Notification
159
Table of Contents
Section 1: Warranty & Service
WARNING: Read all instructions in this manual and component manufacturer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole purpose of providing instructions concerning the operation and maintenance of this recreational vehicle. Nothing in this manual creates any warranty, either expressed or implied. The owner's failure to provide required service and/or maintenance could result in the loss of warranty. Please review the limited warranty and the limited warranties that apply to specific components offered with this vehicle. Instructions are included in the manual for operating various components which are optional on some RV's or may not be available on your particular model. "If so equipped" does not indicate or imply that the component(s) or option(s) were at any time available, or can be retrofitted to your model. In addition, the owner should refer to individual manufacturer's operating instructions contained in the owner's packet.
Maintenance Record
Table of Contents
1
Section 1: Warranty & Service
Congratulations! Thank you for selecting a Jayco recreation vehicle. We are excited to welcome you to our growing RV family. We are committed to being the most respected name in RVs. We invite you to drop by our Visitors Center located in Middlebury, Indiana.
Jayco recreation vehicles are manufactured for use as temporary living quarters for recreation, camping and travel uses, all as defined by the bylaws of the Recreation Vehicle Industry Association (RVIA).
This recreation vehicle is not intended for use as a full-time residence or for commercial use. Commercial use means using the recreation vehicle as a business asset such as a mobile office or using the recreation vehicle for lease or rental purposes.
Jayco reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever. Recreation vehicles built for sale in Canada may differ to conform to Canadian Codes. Factory Tours To book a factory tour or check on available tour times (free admission, closed holidays) please log on to https://www.jayco.com and hold the mouse pointer on the ABOUT JAYCO heading (bottom of page). Select "FACTORY TOURS" from the drop down menu that opens.
Options and Equipment Jayco recreation vehicles are available in several sizes and models, so accessories and components may differ slightly between models. Some equipment described in this manual may not apply to your recreation vehicle.
Jayco reserves the right to discontinue or change specifications or design at any time without notice, and to make additions or improvements without incurring any obligations upon itself to install these changes on its products previously manufactured. Recreation vehicles built for sale in Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to:
Deliver your recreation vehicle in the best condition possible. Your recreation vehicle must pass the dealer's pre-delivery inspection (PDI), including all systems tests.
Provide orientation of the recreation vehicle, its systems, components and operation.
Request that you read all warranty information and explain any provision not clearly understood.
Ensure you receive the Warranty Packet. Your dealer can assist you in completing the OEM warranty cards or registrations, and locate any required component model or serial numbers.
Complete and return the "Warranty Registration and Customer Delivery Form" to Jayco within 10 days of delivery to activate the applicable warranty coverage.
The Limited Warranty is activated only after Jayco receives a signed and dated "Warranty Registration and Customer Delivery Form" from your dealer.
Customer Relations Jayco has empowered its dealers to make warranty and repair decisions.
If a special circumstance occurs that requires information from Jayco, we have asked your dealer's service management to make the contact on your behalf. This is why you should always talk to your dealer's service management first.
Customer name and current location. Phone number where you can be reached. 17-digit chassis Vehicle Identification Number (VIN) or 9-digit Serial.
2
Maintenance Record
Table of Contents
Section 1: Warranty & Service
The current vehicle mileage (motorhomes). Your date of purchase. If applicable, the component description, serial number and model number. A detailed description of the concern. The name of your selling dealer. If different from above, the contact information for the RV repair facility you are
contacting Jayco to discuss.
An important note about alterations and warranties Installations or alterations to the original equipment vehicle as distributed by Jayco are not covered by the Jayco Limited Warranty. The special body company, assembler, equipment installer or up fitter is solely responsible for warranties on the body or equipment and any alterations (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.
Obtaining Emergency Warranty Repair 1. Call 1-(800)-283-8267 or use our website dealer locator to find an authorized Jayco
dealer in your area. Contact them for an appointment; they will handle all warranty repair billing and returned parts for you. 2. If you cannot locate an authorized Jayco dealer near you, ask the campground staff for referrals or check the local telephone yellow pages. Or contact Jayco Customer Service or your selling dealer for assistance in locating a repair facility. Contact the RV repair facility to discuss your situation and make an appointment.
Ask how their billing will be handled. They may choose to bill Jayco directly; otherwise, you are expected to pay them. Have the RV repair facility inspect your RV. Either they or you must call Jayco Customer Service to discuss applicable warranty coverage prior to any repair work being performed. Jayco Customer Service will issue an authorization number upon warranty repair approval and advise if any original parts need to be returned. Once Jayco Customer Service has issued an authorization number, the RV repair facility may begin actual repair to your RV. Inspect the completed repair work thoroughly. If you are not satisfied, communicate that immediately to the RV repair facility management. Make sure you are satisfied with the repair before you pay or leave the premises. For reimbursement, either you or the RV repair facility must send a copy of your itemized repair bill and all requested return parts by UPS (regular ground, freight pre-paid) within 60 days of the completed repair date.
To expedite processing your warranty claim, include your name, address, phone number, RV 17-digit VIN and authorization number. If returning parts, include a copy of your return freight bill.
Obtaining weekend or after business hours repair assistance If an authorized Jayco dealer is not located nearby, contact your selling dealer for assistance. If your dealer is closed, check with the campground staff or telephone yellow pages for an RV repair facility. Have the item repaired and contact Jayco Customer Service immediately the following business day.
Failure to contact Jayco Customer Service, unauthorized or improper warranty repairs, or failure to return requested original parts may result in loss of reimbursements and/or loss of warranty.
Maintenance Record
Table of Contents
3
Section 1: Warranty & Service
To Contact Us Mailing address
Jayco, Inc.
Shipping address Jayco, Inc.
Customer Service
Customer Service
P.O. Box 460
100 Bontrager Drive
903 S. Main Street
Bldg 42 Door 4220
Middlebury IN 46540
Middlebury IN 46540
Phone (toll-free)
(800) 283-8267
Phone (local)
(574) 825-0608
Fax (toll-free)
(866) 709-9139
Brochure request
info@Jayco.com
Parts email
parts@Jayco.com
Service email
service@Jayco.com
Website
www.Jayco.com
Jayco Travel Club
All owners of Jayco recreation vehicles are eligible for membership in the Jayco Travel
Club.
The club promotes family camping and the active use of your RV with others who have similar interests in the RV lifestyle.
One "International Rally" is held each year in various locations around the United States and Canada. In addition, the club offers a variety of local and regional activities throughout the year.
By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.
For more information, please visit www.Jaycorvclub.com or call 1-800-262-5178.
4
Maintenance Record
Table of Contents
Section 1: Warranty & Service
About This Manual
This manual is a guide to operation of the features, equipment and controls in your recreation vehicle. If you find components vary significantly from what is described, please contact your dealer to ensure you have the correct information. Nothing in this manual creates any warranty, either expressed or implied.
This Owner's Manual and Warranty Packet are to be considered permanent components of the vehicle. Keep them in your recreation vehicle at all times for personal reference. If the recreation vehicle is sold, they should remain with the vehicle for the next owner. Nothing in this manual creates any warranty, either expressed or implied, nor does it cover every possible detail of equipment, standard or option, installed on or in your recreation vehicle. Information, illustrations and specifications in this manual reflect the most current available at the time of publication approval, are subject to change and not intended to indicate actual size.
Warranty Packet
There are components that are excluded from the vehicle warranty, or are warranted separately by their own individual manufacturer's limited warranty. The Warranty Packet contains these component manufacturer supplied manuals or information sheets, warranty cards and/or registrations. Consult this information for questions regarding operating, maintenance, servicing instructions and warranty coverage. It is important you complete and mail warranty cards and registrations within the prescribed time limits to avoid loss of warranty coverage.
Chassis Guide
Throughout this manual, frequent reference is made to the vehicle's Chassis Guide. The Chassis Guide includes the owner's manual provided by the manufacturer of the chassis on which this motorhome is built, warranty cards and/or registrations. It also includes pertinent information regarding the transmission, tires, etc. Consult the Chassis Guide for operating safety, maintenance, servicing instructions and warranty coverage. The Chassis Guide should be considered a permanent component of the vehicle and kept in the motorhome at all times for reference.
Safety Alerts
Throughout this manual, certain items are labeled NOTE, CAUTION, WARNING, and DANGER. These terms will alert you to precautions that can involve risk to your vehicle or to your personal safety.
Read and follow them carefully. National Safety Associations and organizations require many of the instructions listed. Always use the appropriate safety gear when servicing or maintaining your recreation vehicle. Please call your dealer or our customer service representatives if you are unsure how to proceed.
These signal words indicate precautions and potential situations, which if not avoided, may result in personal injury, property damage, or damage to your recreation vehicle. These precautions are listed in the appropriate areas in this Owner's Manual, and in the information contained in the Warranty Packet, and on safety labels affixed to your recreation vehicle. Read and follow them carefully.
Maintenance Record
Table of Contents
5
Section 1: Warranty & Service
NOTE: Gives helpful information.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a potential situation that,if not avoided, may result in property damage or damage to your motorhome.
Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This alert information is limited to the most extreme situations.
Indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury.
Reporting Safety Defects
In the United States: If you believe that your recreation vehicle has an alleged defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying our Customer Service Department. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
However, NHTSA cannot become involved in individual problems between you, your dealer or your vehicle manufacturer. For additional information, please refer to the NHTSA website at www.safercar.gov.
To contact NHTSA by phone: Call the Department of Transportation (DOT) Vehicle Safety Hotline at 1-888327-4236, and a NHTSA representative will record your complaint information (TTY: 1-800-424-9153 or 1-202-484-5238).
6
Maintenance Record
Table of Contents
Section 1: Warranty & Service
To Contact NHTSA by mail: Office of Defects Investigations/CRD NVS-216 1200 New Jersey Ave SE Washington, DC 20590
In Canada: If you believe your vehicle has an alleged safety defect, you should contact Transport Canada and our Customer Service Department immediately.
To file a safety concern, you can complete an on-line form at https://tc.canada.ca/en/roadtransportation/defects-recalls-vehicles-tires-child-car-seats/report-potential-safety-defectvehicles-tires-child-car-seats, or call to speak with a defect investigator.
For additional information, please refer to the Transport Canada website at www.tc.gc.ca/ recalls
To contact Transport Canada by phone: 819-994-3328 (Ottawa-Gatineau area or internationally) Toll free: 1-800-333-0510 (in Canada) To contact Transport Canada by mail: Transport Canada -ASFAD 330 Sparks Street Ottawa, ON K1A 0N5 www.tc.gc.ca/rappels Téléphone: 819-994-3328 (dans la région de Ottawa-Gatineau et à l'extérieur du pays) Sans frais: 1-800-333-0510 (au Canada) Adresse postale : Transports Canada -ASFAD 330, rue Sparks Ottawa (Ontario) K1A 0N5
Customer Responsibility
It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV'er we encourage you to thoroughly read this Owner's Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).
As technology advances, new improvements enter the RV industry every day, and each RV manufacturer has its own unique manufacturing process.
Familiarize yourself with the Limited Warranty applicable to your recreation vehicle. There are components that are excluded or warranted separately by their individual manufacturer's limited warranty (refer to the Warranty Packet or Chassis Guide if applicable).
As the new owner of the recreation vehicle, you are responsible for regular and proper maintenance performed in accordance with this manual and the OEM manuals. Regular and proper maintenance will help prevent conditions arising from neglect that are not covered by the limited warranty. It is your responsibility and obligation to return your vehicle to your dealer for repairs and service.
Change Of Address/Ownership
Please notify our Customer Service Department as soon as possible of a change of address by writing or calling us. For notification of a change of ownership, please fill out the appropriate form located in this manual and mail it to Customer Service along with documentation showing proof of ownership. Please include your current vehicle mileage (motorized only).
Maintenance Record
Table of Contents
7
Section 1: Warranty & Service
Suggestions For Obtaining Service
To help ensure your dealer provides the level of service you expect, here are some suggestions we would like to make:
Contact your dealer at once... Do not wait until you are ready to use your RV. Your dealer may not be able to service it immediately and/or the repair may require parts be ordered. The dealer's service department is busiest on Mondays, Fridays and before the holidays.
Prepare for the appointment... If you are having warranty work performed, be sure to have the right papers with you. Take your warranty folder and have your vehicle information available. All work to be performed may not be covered by the warranty. Discuss additional charges with the service personnel.
Prepare a list... Provide your dealer with a written list of specific repairs needed. It is important that you provide any vehicle repair history to the dealer's service personnel.
Keep a maintenance log of your vehicle's service history. This can often provide a clue to the current issue.
Be reasonable with your requests... If you leave a list with several items and you need your vehicle returned back by a specific time, discuss the situation with the dealer's service personnel and list your items in order of priority. This may include making a second appointment for work not completed or parts that the dealer may need to order.
Don't expect to look over the technician's shoulder... Please don't be offended if you are told you cannot watch the work being done. Some insurance requirements forbid admission of customers to the service area.
Inspect the work performed... Finally, check out the service or repair job when you pick up your vehicle. Notify the dealer's service personnel immediately of any dissatisfaction. If you cannot return the vehicle immediately for repair, make an appointment as soon as possible.
Please be aware that all service shops require notification of any issues with their repairs within a specified time limit. Make sure you are familiar with their repair policies.
Obtaining Service For Separately Warranted Items
Your selling dealer is responsible for servicing your recreation vehicle before delivery, and has an interest in your continued satisfaction. We recommend your dealer perform all inspection, warranty and maintenance services. Some dealers may be authorized service centers for those OEMs whose products are warranted separately and excluded from the Limited Warranty.
Obtaining Service At Our Customer Service Faciity
Should your recreation vehicle be in need of service, and your dealer recommends that the repairs be made at our Customer Service facility, your recreation vehicle may be returned to us with the following guidelines*:
You or your dealer must make a confirmed appointment 60 days prior to dropping off the recreation vehicle at our Customer Service facility.
The holding tanks must be emptied and rinsed. We have a dumping station available for customer use.
The propane system (if so equipped) and all electrical systems must be shut down and turned off. We are not responsible for discharged batteries or propane tanks.
During the appropriate season, please ensure the RV has been winterized.
8
Maintenance Record
Table of Contents
Section 1: Warranty & Service
Unless prior approval has been obtained from our Customer Service facility, all personal items must be removed from the area where you are requesting service repair and the refrigerator emptied. We are not responsible for loss of food items.
All transportation costs are the responsibility of the owner. You may need to arrange for alternative accommodations for some types of repairs. Please be prepared accordingly.
*Our Customer Service facility occasionally utilizes local independent repair facilities. Your vehicle may be referred to or repaired by one of these local repair facilities.
Parts and Accessories
Contact your authorized dealer for assistance in obtaining replacement parts or accessories. We do not sell direct to retail or non-authorized dealers. If the original part is no longer available, we will make every effort to provide an appropriate substitute.
Maintenance Record
Table of Contents
9
Section 1: Warranty & Service
2022 JAYCO MOTORIZED LIMITED WARRANTY
THIS LIMITED WARRANTY COVERS:
· The Motor home when it is used only for its intended purpose of recreational travel and camping;
· Only the first retail purchaser;
· Only those portions of the Motor home not excluded under the section "What is Not Covered";
· The Motor home only when sold by an authorized dealership; and,
· Only defects in workmanship performed and/or materials used to assemble those portions of the Motor home not excluded under the section "What is Not Covered".
· This Limited Warranty is not transferable.
When you request and accept the performance of warranty repairs under the terms of this Limited Warranty, you are accepting all terms of this Limited Warranty, including by way of example, warranty limitations and disclaimers, the forum selection clause and the clause reducing the time period when suit must be filed for breach.
LIMITATION AND DISCLAIMER OF IMPLIED WARRANTIES: THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO:
· THE DURATION OF THIS LIMITED WARRANTY;
· THE SCOPE OF COVERAGE THIS LIMITED WARRANTY PROVIDES;
· DEFECTS EXISTING AT THE TIME OF SALE THAT MANIFESTED THEMSELVES AND SURFACED DURING THE IMPLIED WARRANTY COVERAGE PERIOD; AND
· DEFECTS DISCOVERED AND REPORTED WITHIN THE DURATION OF THE IMPLIED WARRANTY. THERE ARE NO EXPRESS WARRANTIES OR ANY IMPLIED WARRANTIES ON THOSE PORTIONS OF THE MOTOR HOME EXCLUDED FROM COVERAGE.
NOTWITHSTANDING THE ABOVE PROVISIONS, JAYCO EXPRESSLY DISCLAIMS AND EXCLUDES ANY AND ALL IMPLIED WARRANTIES AND CONDITIONS, STATUTORY OR OTHERWISE, WHEN THE MOTOR HOME IS USED FOR COMMERICAL, RENTAL OR BUSINESS USE OR WHEN THE MOTOR HOME IS TITLED OR REGISTERED IN A BUSINESS NAME OR WHEN THE JAYCO IS SOLD IN CANADA. There is no warranty of any nature made by Jayco beyond that contained in this Limited Warranty. No person has authority to enlarge, amend or modify this Limited Warranty. The dealer is NOT Jayco's agent. Jayco is not responsible for any undertaking, representation or warranty made by any dealer or others beyond those expressly set forth within this Limited Warranty. Some states and provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES: THE FIRST RETAIL BUYER AND ANY SUBSEQUENT OWNER, ALONG WITH ANY PERSON WHO IS AN INTENDED OR UNINTENDED USER OR BENEFICIARY OF THE MOTOR HOME, ARE NOT ENTITLED TO RECOVER ANY
10
Maintenance Record
Table of Contents
Section 1: Warranty & Service
CONSEQUENTIAL OR INCIDENTAL DAMAGES CAUSED BY A DEFECT IN THE MOTOR HOME. BY WAY OF EXAMPLE, CONSEQUENTIAL DAMAGES INCLUDE FUEL AND TRANSPORTATION EXPENSES TO DELIVER THE MOTOR HOME TO A SERVICING DEALER, HOTEL ROOMS, LOST WAGES AND MOISTURE DAMAGE SUCH AS MOLD AND MILDEW AS WELL AS RUST AND CORROSION. THE EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES ARE NOT DEPENDENT UPON WARRANTY REMEDIES SUCCESSSFULLY CURING ANY DEFECT; THE EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES SHALL SURVIVE ANY FAILURE OF THE LIMITED WARRANTY REMEDIES FULFILLING THEIR PURPOSE. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusions may not apply to you.
COVERAGE TIME: The duration of this limited warranty is 2 years after the first retail owner takes delivery of the Motor home from an authorized dealer OR 24,000 miles of use, whichever occurs first. If the dealer places the Motor home in service before retail sale, the coverage period is 2 years after the dealer first placed the Motor home in service OR 24,000 miles of use, whichever occurs first. ANY ACTION FOR BREACH OF THIS LIMITED WARRANTY OR FOR ANY IMPLIED WARRANTY MUST BE COMMENCED NO MORE THAN 26 MONTHS AFTER THE BREACH.
The term of this limited warranty is 3 years for substantial defects to any "Structure Components". Structure Components means materials and/or workmanship directly attributable to Jayco relating to the lamination of the fiberglass sidewall assembly, the lamination of the rear wall assembly, the lamination of the fiberglass front wall (wrap) assembly, sidewall/end wall/front and rear wall frame assembly (wood and aluminum), roof frame assembly (wood and aluminum), and floor frame assembly (wood and aluminum). Structure Components specifically excludes front and rear fiberglass caps and any other cosmetic fiberglass attachments, sidewall metal (unless the root cause is the wall structure); exterior roof material (EPDM rubber, TPO, etc.); floor covering (carpet, linoleum, hardwood tile, etc.); all sidewall, end wall, front and rear wall, roof and floor attachments, and delamination caused by water intrusion from lack of required exterior seal maintenance or other maintenance. Structure Components further excludes all items identified under "What is Not Covered" below.
Jayco reserves the right to have new or remanufactured parts of similar quality used to complete any work, and to make parts and design changes from time to time without notice to anyone. Jayco reserves the right to make changes in the design or material of its products without incurring any obligation to incorporate such changes in any product previously manufactured. Jayco makes no warranty as to the future performance of the Motor home, and this limited warranty is not intended to extend to the future performance of the Motor home, or any of its materials, components or parts. In addition, the Motor home owner's obligation to notify Jayco, or one of its independent, authorized dealers, of a claimed defect does not modify any obligation placed on the Motor home owner to contact Jayco directly when attempting to pursue remedies under state or federal law.
If the Motor home is not of the current or prior model year when the first retail owner takes delivery, the limited warranty, including but not limited to the limited warranty for substantial defects to Structure Components, ends 90 days after the first retail owner takes delivery of the Motor home OR after the odometer reaches 5,000 miles, whichever occurs first. ANY ACTION FOR BREACH OF THIS REDUCED LIMITED WARRANTY OR FOR ANY IMPLIED WARRANTY MUST BE COMMENCED NO MORE THAN 15 MONTHS AFTER THE BREACH.
Maintenance Record
Table of Contents
11
Section 1: Warranty & Service
Unless prohibited by state or provincial law, repairs do not extend the time when you must commence an action for breach of warranty and shall not extend the warranty coverage period. This reduction in time may not apply to you because some states and provinces do not allow the reduction of the time to commence an action for breach of warranty. Any performance of repairs after the warranty coverage ends and any performance of repairs to those portions of your Motor home excluded from coverage are "good will" repairs, whether or not Jayco was aware of any such coverage lapse or warranty exclusion at the time of repairs. Such "good will" repairs do not alter the express terms of this limited warranty or extend the warranty coverage periods or the limitation period in this paragraph. Jayco is not required to notify you if authorized repairs are considered "good will" by Jayco. You should expect the need for warranty repairs. Jayco may use new and/or remanufactured parts and/ or components to complete a repair. It is likely that warranty repairs were performed at the factory during assembly OR at the selling dealership after delivery of the Motor home to your selling dealer. If you discover a defect or damage to the Motor home when you take delivery of your Motor home, you MUST notify your dealer OR Jayco within 10 days of the date of purchase to have defect or damage repaired at no cost to you. Minor adjustments will be performed, free of charge, by the dealer within 90 days of your purchase; thereafter, such adjustments are your exclusive responsibility as normal maintenance.
REPAIR REMEDY: Jayco's obligation is to repair any covered defect discovered within the warranty coverage period provided: (1) you notify Jayco or an authorized dealer within 10 days of your discovery of a defect; AND (2) you deliver the Motor home to Jayco OR an authorized dealership at your cost and expense.
BACK-UP REMEDY: If the primary repair remedy fails to successfully cure any defect after a reasonable number of repair attempts, your sole and exclusive remedy shall be to have Jayco pay an independent service shop of your choice to perform repairs to the defect OR have Jayco pay diminished value damages if the defect is incurable. You must exhaust both the repair remedy and the back-up remedy AND these remedies must fail to fulfill their essential purpose before you can seek any other remedies.
THIS LIMITED WARRANTY IS NOT A WARRANTY THAT PROMISES OR EXTENDS TO FUTURE PERFORMANCE BECAUSE IT DOES NOT MAKE A REPRESENTATION ON HOW YOUR MOTOR HOME WILL PERFORM IN THE FUTURE BUT REPRESENTS ONLY WHAT THE REMEDY WILL BE IF A DEFECT EXISTS.
HOW TO GET SERVICE: To obtain warranty service the owner must: · Notify Jayco or an authorized Jayco dealer, within the applicable warranty coverage
period designated above, that you are making a warranty claim;
· Provide the notification mentioned in (1), above, within ten (10) days of the discovery of a defect in material or workmanship; and,
· Promptly schedule an appointment with and take the Motor home to Jayco or an independent, authorized dealer.
If you need assistance, you may contact JAYCO, INC. at 903 South Main Street, P. O. Box 460, Middlebury, Indiana 46540, Attn: Customer Service, (800) 283-8267.
WHAT IS NOT COVERED: · Equipment and appliances installed after the Motor home is assembled by Jayco;
· Motor homes used for any rental, business and commercial purpose - If the Motor home owner or user files a tax form claiming a business or commercial tax benefit related to the Motor home, or if the RV is purchased, registered or titled in the name of any business association it shall be irrefutable that the Motor home has been used for rental, commercial or business purposes;
12
Maintenance Record
Table of Contents
Section 1: Warranty & Service
· Any Motor home sold or used outside of the United States, U.S. Territories or Canada;
· Any Motor home not used solely for recreational travel and camping;
· Any Motor home purchased through auction or wholesale;
· Any Motor home purchased from a dealer that is not an authorized dealer;
· Normal wear, tear or usage, such as tears, punctures, soiling, mildew, rust, fading, or discoloration of exterior plastic or fiberglass, or soft goods, such as upholstery, drapes, carpet, vinyl, screens, cushions, mattresses and fabrics;
· The effects and damage caused by condensation or moisture; · Mold;
· Any damage caused by mold;
· Items working as designed but that you are unhappy with;
· Damage caused by misuse, mishandling, neglect, abuse, failure to maintain the Motor home in accordance with the owner's manual, or failure to perform other routine maintenance such as inspections, lubricating, adjustments, tightening of screws and fittings, tightening of lug nuts, sealing, rotating tires;
· Damage caused by accident, whether or not foreseeable;
· Damage caused by weather or corrosion due to the environment;
· Damage caused by theft, vandalism or fire; · Damage caused by tire wear or tire failure;
· Defacing, scratches, dents, chips on any surface or fabric of the Motor home; damage caused by infestation by insects or animals;
· Damage caused by off road use; · Damage caused by overloading the Motor home or any of its components or parts;
· Wheel alignment or adjustments to axles caused by improper maintenance, loading;
· Damage caused by road hazards;
· The leveling jacks/system;
· Any component, system or part warranted by another entity. Examples are : the automotive chassis, (including the power train, steering, handling, braking, wheel balance, muffler, tires, tubes, batteries and gauges); generator; awning ; inverter; converter; microwave; television; DVD/CD player; radio; speakers; television; refrigerator; range; water heater;, water pump; stove; carbon monoxide detector; smoke detector: propane detector; furnace; and, any air conditioner. The written warranty provided by the manufacturer of the component part is the direct and exclusive responsibility of that manufacturer).
EVENTS DISCHARGING JAYCO FROM OBLIGATION UNDER WARRANTY: · Any rental, business or commercial use or purchase of the Motor home;
· Any Motor home titled or registered in a business name;
· Any Motor home purchased or sold outside of, or used outside of the United States, U.S. Territories or Canada;
· Any Motor home purchased through an auction or wholesale or by a non-authorized dealer;
Maintenance Record
Table of Contents
13
Section 1: Warranty & Service
· Owner neglect;
· Failure to provide routine maintenance;
· Alteration; off road use;
· Collision or accident, whether or not foreseeable;
· Acts of God, including weather;
· Damage or corrosion caused by the environment, theft, vandalism, fire, explosions, or overloading.
LEGAL REMEDIES: EXCLUSIVE JURISDICTION FOR DECIDING LEGAL DISPUTES RELATING TO AN ALLEGED BREACH OF WARRANTY OR ANY REPRESENTATIONS OF ANY NATURE, MUST BE FILED IN THE COURTS WITHIN THE STATE OF MANUFACTURE, WHICH IS INDIANA. THIS LIMITED WARRANTY SHALL BE INTERPRETED AND CONSTRUED IN ACCORDANCE WITH THE LAWS OF THE STATE OF INDIANA. UNLESS PROHIBITED BY STATE LAW, ALL CLAIMS, CONTROVERSIES AND CAUSES OF ACTION ARISING OUT OF OR RELATING TO THIS LIMITED WARRANTY SHALL BE GOVERNED BY THE LAWS OF THE STATE OF INDIANA, INCLUDING ITS STATUTE OF LIMITATIONS, WITHOUT GIVING EFFECT TO ANY CONFLICT OF LAW RULE THAT WOULD RESULT IN THE APPLICATION OF THE LAWS OF A DIFFERENT JURISDICTION. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE AND PROVINCE TO PROVINCE. ALL ACTIONS OF ANY KIND RELATING TO THE MOTOR HOME SHALL BE DECIDED BY A JUDGE RATHER THAN BY A JURY. WARRANTY REGISTRATIONS: Your warranty registrations should be completed and delivered to the manufacturer of component parts. The selling dealership will assist you in completing and filling out the Jayco product warranty registration. Upon receipt of the product registration by Jayco, your Warranty will be registered. The failure to submit this warranty registration to Jayco will not affect your rights under this limited warranty as long as you can present proof of purchase, however, it can cause delays in obtaining the remedies offered by this limited warranty, and it may adversely affect any servicing facility's ability to provide proper repairs and/or part replacement. Note, tender and acceptance of a warranty registration does not alter the express terms of this limited warranty or any of its exclusions. CARE AND MAINTENANCE: It is the Owner's responsibility to perform proper care and maintenance of the Motor home and to assure correct load distribution. For details regarding this, please see your owner's manuals. Please review all manuals and contact your selling dealership, Jayco or supplier of the component part if you have questions. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS; YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
JAYCO, INC.
903 S. Main Street * P. O. Box 460 * Middlebury, IN 46540 Telephone: 800-283-8267
14
Maintenance Record
Table of Contents
Section 1: Warranty & Service
Maintenance Record
Table of Contents
15
Section 1: Warranty & Service
Notes:
16
Maintenance Record
Table of Contents
Section 2: Occupant Safety
Secondary Means of Escape (Exit Window)
Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emergency if access to the main entrance door is not available. It is easily identified by the red latches and label.
Do not remove the EXIT window label from your RV: When parking your recreation vehicle, make sure the egress window is not blocked by trees or other obstacles. Make sure the ground below the window is solid and can be used as an escape path.
Exit Window Label
Practice opening the window before an emergency occurs, and make sure all occupants know how to operate it.
Exercise care when opening the exit window. If opened too far, it may come off the hinge. This may result in damage to the unit or window.
NOTE: All windows must be closed and locked while the RV is in transit.
Your recreation vehicle may be equipped with one of the following exit window styles:
Flip latch style (2 per window) Push up on the front lip of the latch and the latch unfolds. Push up on the front lip of the latch again to unhook the latch from the window. When both latches are released, push out on the window which is hinged at the top. Exit the vehicle. The screen does not need to be removed from the window.
Slider window latch style Pull the lever down to unlock the window.
Slide the window to the right to open and exit the vehicle.
The screen does not need to be removed from the window.
Maintenance Record
Table of Contents
17
Section 2: Occupant Safety
Lever style latch Remove the screen by pulling the red tab (upper right arrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the window. Push the lever (and window) out to open and exit the vehicle.
Fire Safety
If a fire does start, follow these basic safety rules: 1. Call 911 and evacuate the vehicle immediately. 2. After everyone is accounted for, check the fire to see if you can attempt to put it out. 3. If it is large, or the fire is fuel-fed, get clear of the vehicle and have the Fire Department
handle the emergency. 4. Do not attempt to use water to put out the fire. Water can spread some types of fire, and
electrocution is possible with an electrical fire. Refer to the following sections for additional fire safety information.
Electrical Systems, In case of an electrical fire. Appliances, In case of a grease fire.
Fire Extinguisher
Fire extinguishers are classified and rated by fire type, A, B and C. These classifications identify the kinds of fires or burning materials they are designed to fight. Class A - Solid materials such as wood, paper, cloth, rubber and some plastics. Class B - Liquids such as grease, cooking oils, gasoline, kerosene or other flammable liquids. Class C - Electrical such as electrical wires or other live electrical equipment. A dry chemical fire extinguisher has been installed by the entrance door. It is suitable for extinguishing small fires of the Class B or C type only. We suggest you become thoroughly familiar with the operating instructions displayed on the side of the fire extinguisher.
NOTE: For information on how to use your fire extinguisher, refer to the fire extinguisher user's manual included in your warranty packet.
Inspection and maintenance Read and follow all instructions on the label and user's manual provided by the fire extinguisher manufacturer.
Inspect the extinguisher at least once a week (more frequently if it is exposed to weather or possible tampering). This should also be done before beginning a vacation or during an extended trip.
18
Maintenance Record
Table of Contents
Section 2: Occupant Safety
Do not check the pressure, test or practice using the fire extinguisher by squeezing the trigger, even briefly. The fire extinguisher is not rechargeable or refillable. Once used, it will gradually lose pressure and will not be fully
charged for use in an emergency.
Do not turn the electrical power back on or plug in any appliances after the use of a fire extinguisher. Please refer to the fire extinguisher's user manual for further instructions on maintenance and clean up.
Smoke Alarm
The smoke alarm will only work properly if it is operational and maintained. They have a limited life and will wear out over time. Immediately replace the detector if it is not working properly, if it displays any type of problem, or within five years of use. Be sure to read, understand and follow the information provided by the smoke alarm manufacturer, including information on the limited life of smoke alarms. Be aware the smoke alarm is not fool proof and cannot detect fires if smoke does not reach it. Anything preventing smoke from reaching the alarm may delay or prevent an alarm.
Though the alarm horn in this detector meets or exceeds current UL standards, it may not be heard for reasons that include (but not limited to): a closed or partially closed door, other noise from electronics, appliances or traffic.
This smoke alarm will not alert hearing impaired residents. Special alarms with flashing strobe lights are recommended for the hearing impaired
Only use the replacement battery recommended by the smoke detector manufacturer. The smoke detector alarm may not operate properly with other batteries. Never use a rechargeable battery as it may not provide a constant charge. Never disconnect the battery to silence the alarm.
Test the smoke alarm operation after the vehicle has been in storage, before each trip and at least once per week during use. Do not disconnect the battery or the alarm.
The smoke alarm is operational once the battery is correctly installed. It will not function if the battery is missing, disconnected, dead, the wrong type or not installed correctly. It requires one standard 9V battery. Refer to the user's guide, for correct battery and installation information,
The LED light will indicate the battery is functioning properly. When the production of combustion is sensed, the smoke detector sounds a loud alarm that continues until the air is cleared. The LED light will also give a visual indication of a sounding alarm.
Maintenance Record
Table of Contents
19
Section 2: Occupant Safety
When the battery becomes weak, the alarm will "beep" about once a minute indicating a low battery. This warning should last for 30 days. You MUST replace the battery once the alarms low battery warning (beep) starts to assure continued protection.
When the battery is removed from the alarm, the battery flag will pop up; the alarm cannot be installed to the mounting bracket without a battery.
To test, stand at arm's length from the smoke alarm as the alarm horn is loud and may be harmful to your hearing. The test button will accurately test all functions. Never use an open flame to test the smoke alarm. Do not remove the warning label located near the smoke alarm from your recreation vehicle: Key Features:
· Silence Feature: Silences nuisance alarms · Hinged cover allows for easy battery replace-
ment
· Lighted Power and Alarm Indicator. LED indicates battery is connected.
· Test/Silence button One touch button combines both features · Low Battery indicator Beeping signal indicates low battery.
Maintenance Vacuum off any dust on the cover of the smoke alarm using a soft brush attachment. Test the smoke alarm once you have vacuumed. Never use water, cleaners or solvents to clean the smoke alarm as they may damage the alarm. Do not paint the smoke alarm.
Refer to and follow detailed safety, testing, troubleshooting and maintenance information found in the manufacturer's user pamphlet located in your warranty packet.
Combination Carbon Monoxide /Propane Alarm
Your recreation vehicle is equipped with a combination carbon monoxide (CO) / propane alarm (RVCOLP) that is listed for use in recreation vehicles. The combination carbon monoxide/propane alarm will only work if it is operational and maintained.
The alarm is directly wired to the 12-volt electrical system, with continuous power being supplied by the recreational vehicle batteries. There is no 9-volt battery power supply. As a result, the alarm is always drawing a small amount of current from the recreation vehicle batteries. Although the current draw is slight, it could drain the batteries during extended storage periods. This condition is not likely to occur except during storage situations when the inverter cannot restore the battery charge. If the battery cable is disconnected at the battery terminals, the combination alarm will not work. Be sure to read, understand and follow the owner's information from the manufacturer of the combination CO/propane alarm. This includes information regarding the limited life of the alarm.
20
Maintenance Record
Table of Contents
Section 2: Occupant Safety
Do not cover or obstruct the carbon monoxide/propane alarm with anything that could prevent gas from entering the alarm.
This alarm is not designed to detect smoke, fire or gases other than carbon monoxide and propane.
The carbon monoxide detector installed is intended for use in ordinary indoor locations of recreation vehicles. It is not designed to comply with Occupational Safety and Health Administration (OSHA) commercial or industrial standards.
Do not disconnect the battery or the alarm. Individuals with medical problems may consider using warning devices
that provide audible and visual signals for carbon monoxide concentrations under 30 PPM. This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas. The ultimate responsibility for protection against toxic carbon monoxide fumes rests solely on you. Installing a carbon monoxide/propane alarm is just the first step in protecting your family from toxic carbon monoxide poisoning. The following symptoms are related to carbon monoxide poisoning and should be discussed with all members of the household: Mild exposure: Slight headache, nausea, vomiting, fatigue (often described as "flu-like" symptoms). Medium exposure: Severe throbbing headaches, drowsiness, confusion, fast heart rate Extreme exposure: Unconsciousness, convulsions, cardio-respiratory failure, death
Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless and tasteless gas. Many cases of reported carbon monoxide poisoning indicate while victims are aware they are not well, they become so disoriented they are unable to save themselves by either exiting the recreational vehicle or calling for assistance. Young children and household pets may be the first affected.
Your combination carbon monoxide/propane alarm is designed to detect the toxic carbon monoxide fumes that result from incomplete combustion, such as those emitted from appliances, furnaces, fireplaces and auto exhaust.
A carbon monoxide/propane alarm is NOT A SUBSTITUTE for other combustible gas, fire or smoke alarms. This carbon monoxide alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is not designed to detect smoke, fire or any other gas. Please note that there are hazards against which carbon monoxide detection may not be effective, such as natural gas leaks or explosions.
This alarm is designed to sense the presence of carbon monoxide/propane gas, however there are other combustible fumes or vapors that may be detected by the sensor including (but not limited to): acetone, alcohol, butane and gasoline.
These chemicals can be found in commonly used items such as deodorants, colognes, perfumes, adhesives, lacquer, kerosene, glues, wine, liquor, most cleaning agents and the propellants of aerosol cans.
High temperatures can activate glue and adhesive vapors. If you close up a recreational
Maintenance Record
Table of Contents
21
Section 2: Occupant Safety
vehicle on a hot day, the chemicals used in its construction may be detected for months after the vehicle was constructed (for more information, refer to Sec. 2, Formaldehyde). What you should do if the alarm sounds
Actuation of this detector indicates the presence of carbon monoxide which can kill you.
Never turn the 12-volt battery disconnect control to the off position and disconnect the battery cable to silence an alarm. The alarm will automatically sense when the level of carbon monoxide in the air reaches below dangerous levels. You should stay outside the vehicle in fresh air until the alarm is silenced. When the alarm sounds, do not stand too close to the alarm. The sound produced by the alarm is loud (85db) because it is designed to wake a person in an emergency. Prolonged exposure to the alarm at a close distance may be harmful to your hearing.
CO Alarm State: 1. If CO gas reaches unsafe levels, alarm enters CO alarm state. 2. Horn sounds with (4) rapid chirps, then 4-second pause and red LED flashes rapidly. 3. Operate the SILENCE/TEST button to silence the alarm for 5 minutes.
4. The original alarm state resumes after 5 minutes if CO levels still exceed safe levels. 5. Call your emergency services (fire department or 911). 6. Immediately move to fresh air (outdoors or by an open door or window).
7. Do not re-enter the premises or move away from the open door or window until the emergency service responders have arrived, the premises have been aired out, and your alarm remains in its normal condition.
Propane Alarm State: 1. If propane gas exceeds 10% of the lower explosive limit for more than 30 seconds,
alarm enters propane alarm state.
2. Horn sounds with constant beeps and the red LED will be ON. 3. Turn off all propane appliances and gas valve at LP tanks. 4. Ventilate the RV open doors and windows
5. Alarm can be silenced for 5 minutes by pressing SILENCE/TEST button. 6. Red LED will flash each second while alarm is silenced. 7. Original alarm state resumes after 5 minutes if Propane levels still exceed the safe
levels.
8. Do not touch any electrical switch in or near the recreation vehicle
9. Do not start vehicle's engine or generator If your alarm reactivates within a 24-hour period, repeat steps 1-4 and call a qualified appliance technician to investigate for sources of carbon monoxide from fuel burning equipment and appliances, and inspect for proper operation of this equipment. Make sure that motor vehicle(s) are not, and have not been, operating in an attached garage or adjacent to the recreation vehicle.
If problems are identified during this inspection, have the alarm serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturer's instructions or contact the manufacturer directly for more information about carbon monoxide safety and this alarm.
22
Maintenance Record
Table of Contents
Section 2: Occupant Safety
Alarm features and functions Includes an 85db audible horn, two LEDs, and a SILENCE/TEST button.
Alarm States Normal operation: The Green LED is ON steady. Red LED OFF, Audible horn OFF. Power OFF: Both LEDs and the audible horn will be OFF. Self Test: Green LED OFF, Red LED ON/Flashing, audible horn 4 chirps followed by constant beeps. CO alarm condition: Green LED OFF, Red LED Flashing, audible alarm 4 chirps. Propane gas alarm: Green LED OFF, Red LED ON, audible alarm constant beeps. Alarm Silenced (5 min. max.) Green LED OFF, Red LED flashes each second, Audible horn OFF. Low Battery (Below 8VDC): Green LED flashes each minute, Red LED flashes each minute, audible horn chirps each minute. End of life or other failure: Green and Red LEDs will double flash every minute, audible horn chirps each minute. The alarm should be replaced as soon as possible.
Maintenance Vacuum the alarm cover at least once a year. Clean the cover by hand using a cloth dampened in clean water. Dry with a soft cloth. Do not spray the front panel of the alarm with cleaning agents or waxes. This action may damage the sensor causing an alarm or cause the alarm to malfunction. Do not paint the face of the alarm. Testing the combination carbon monoxide/propane alarm
Test the alarm operation after the motorhome has been in storage, before each trip and at least once per week during use.
The SILENCE/TEST button tests both sensors and battery voltage. The SILENCE/TEST button is located on the front of the alarm. Press and hold the test button for 1 second. The alarm performs 2 cycles of the CO horn pattern (4 rapid chirps followed by a 4 second pause) followed by 2 cycles of the Propane horn pattern (constantly beeping). Green LED is OFF, Red LED is ON/flashing.
NOTE: Pressing the test button does not check the sensor operation. Refer to the carbon monoxide/propane alarm manufacturers user's manual provided with your recreation vehicle for additional information on testing the sensors.
Repair or replace the combination carbon monoxide/propane alarm when the alarm no longer functions. As with any electronic product, it has a limited life. Alarms that do not work cannot protect you.
Maintenance Record
Table of Contents
23
Section 2: Occupant Safety
NOTE: The carbon monoxide/propane alarm manufacturer strongly recommends replacement of the detector five years after the date of purchase.
Formaldehyde
Some components in the recreation vehicle contain formaldehyde-based adhesives that may release formaldehyde fumes into the air for an unknown period of time. Individuals who are allergic to formaldehyde gas fumes may experience irritation to eyes, ears, nose and throat. Indoor air quality may also be affected by leaving your vehicle closed for a period of time. To aid in dissipation, ventilate the recreation vehicle by opening all windows and circulate the air with a fan. This label is located inside the vehicle near the entry door. The label should be left permanently affixed to the recreation vehicle.
Extended Or Full Time Usage
Your new recreation vehicle has been built for enjoyment in a recreational manner. It is not intended for use as full-time quarters or a permanent residence. Continuous living in your vehicle could cause accelerated wear and damage to the various components.
Continuous or permanent living in your recreation vehicle may affect your warranty coverage and may void the "Limited Warranty" applicable to your vehicle.
Cold Weather Usage
When used in freezing or below freezing temperatures, the precautions should be taken: Fresh water and drainage systems - preparations to avoid freeze-ups. Propane gas (if so equipped) and sufficient power is needed for protection from possible freeze-ups on the propane gas regulator. Keep in mind that more frequent furnace operation will substantially increase battery draw and propane gas use. During cool weather usage, ventilation or addition of a dehumidifier may be required to reduce condensation. Check outside extrusions on compartment doors, locks, slide outs, windows, vents, etc., for frozen moisture before operating to avoid damage to parts.
24
Maintenance Record
Table of Contents
Condensation
Section 2: Occupant Safety
Condensation may cause dampness, mildew, mold, staining and, if allowed to continue, it may result in damage to the recreation vehicle (damage caused by condensation is not warrantable). It can also lead to mold or mildew issues, which could be a health hazard.
Condensation is a natural phenomenon. The amount of condensation will vary with climate conditions, particularly the relative humidity. Condensation occurs because there is water vapor present in the air. When the temperature reaches the "dew point" the water vapor in the air condenses and changes to a liquid form.
Proper ventilation or the use of a dehumidifier (customer supplied) will assist in controlling the condensation. Suggestions to eliminate warm moist air:
Crack open windows and roof vents to allow warm moist air to escape. Open the bath roof vent (if so equipped) approximately ½" when showering. Use the range hood fan (if so equipped) when cooking or washing dishes. Avoid hanging wet towels (or clothes) inside the recreation vehicle to dry. If found in cabinets or closets, open the doors slightly to provide ventilation.
Maintenance Record
Table of Contents
25
Section 2: Occupant Safety
Notes:
26
Maintenance Record
Table of Contents
Section 3: Pre-Travel Information
Vehicle Labels
Decals and data plates used throughout the motor home aid in its safe and efficient operation; others give service instructions. Read all decals, data and instruction plates before operating your recreation vehicle. Any decal, data or instruction plate painted over, damaged or removed should be replaced. Keep a record of the 17-digit chassis vehicle identification number (VIN), the 9-digit serial number, and your license number in the event theft or vandalism requires you to supply this information to the authorities.
The factory-installed weight labels are specific to the recreation vehicle for which they are supplied and are not interchangeable. Do not remove these labels from your vehicle. If labels are missing contact your dealer or Customer Service for replacements.
Do not exceed any applicable motor home weight ratings. Doing so could damage your motor home or affect handling and braking characteristics.
Your motor home braking system is designed and rated for operation at GVWR not GCWR.
Weight Terms GAWR - Gross Axle Weight Rating: The value specified by the vehicle manufacturer as the load-carrying capacity of a single axle system, as measured at the tire-to-ground interfaces. This is the total weight a given axle is capable of carrying. GCWR - Gross Combined Weight Rating: The value specified by the motor home manufacturer as the maximum allowable loaded weight of the motor home in combination with its towed trailer or towed vehicle. The tongue weight of a towed vehicle/ trailer counts as part of the motor home cargo. GVWR - Gross Vehicle Weight Rating: The value specified by the manufacturer as the maximum permissible weight of the fully loaded motor home. OCCC - Occupant and Cargo Carrying Capacity: Is equal to the GVWR of the motor home, minus the weight of the motor home, as completed at the factory, minus the weight of all occupants, including the driver, minus the weight of all personal cargo, minus the weight of a full tank of chassis engine fuel and, if applicable, minus the weight of a full tank of propane. The full weight of potable water, including the water heater and the tongue weight of a towed vehicle/ trailer counts as cargo in or on the motor home. Additions to or other changes made to the motor home after it left the factory will affect (reduce) the OCCC. UVW - Unloaded Vehicle Weight: The weight of this motor home as manufactured at the factory with fuel, engine oil and coolants and if applicable, the weight of a full tank of propane. Weight and Capacity Labels The following labels are located on the inward-facing surface of the main entry door of the motor home and on the lower sidewall left of the driver's seat.
Maintenance Record
Table of Contents
27
Section 3: Pre-Travel Information
OCCC Label (Occupant and Cargo Carrying Capacity): The upper portion of this yellow label is federally required and indicates the total combined
weight value of occupants and cargo that may be
placed in or on your motor home as it was manufac-
tured and weighed before leaving the factory.
This label also indicates the number of safety seat Upper Section Federal OCCC Weight
belts that have been installed at the factory. Additions
Label
or other changes made to the motor home after it
left the factory will affect (reduce) the OCCC.
The lower portion of the label is provided voluntarily and indicates the weight value of the motor home as it was manufactured and weighed before leaving the factory. This label also indicates the GCWR of the completed motor home.
The Federal Certification Label is required by the Lower Section Federal OCCC Weight
government to verify the RV complies with all motor
Label
vehicle standards for Canada and the United States.
It includes the following information: Manufacturer
name, VIN, GVWR, GAWR (front/rear), tire and rim
sizes and cold tire inflation pressures.
The motor home towing and braking label is located on the rear bumper above the hitch receiver. Be sure to read and follow the guidelines and information stated on this label. Refer to the Chassis Guide for additional information.
Federal Certification Label
Towing and Braking Warning Label
For more information: Consult a hitch specialist or your dealer for assistance when preparing your motor home for towing a vehicle or trailer.
28
Maintenance Record
Table of Contents
Section 3: Pre-Travel Information Loading Your Motor Home
Never load the motorhome in excess of the GVWR or the GAWR for either axle. Overloading your motorhome may result in adverse handling characteristics and damage to the chassis.
DO NOT EXCEED YOUR GVWR! This means you should weigh your vehicle as loaded for your normal travel to determine the actual weight. If you exceed the GVWR, you MUST remove items from the motor home, or drain liquids, then re-weigh the vehicle to ensure you have achieved a safe weight.
The actual weight of the vehicle, passengers, all options, liquids, the hitch weight of your towed vehicle and your personal cargo is important for you to know so you do not exceed the Gross Vehicle Weight Rating (GVWR) of the motor home. The volume of space available for storage may exceed the amount of available cargo capacity. Large storage compartments have been designed to accommodate normal camping items, which are bulky, but not necessarily heavy.
Store and secure all loose items inside the motor home before traveling. Overlooked items can become dangerous projectiles during a sudden stop.
Distribute cargo side-to-side so the weight on each tire does not exceed one-half of the GAWR for either axle. Make sure any tie down straps (if so equipped) on appliances or furniture are secure. Load heavy objects on the floor, or as low as possible.
Your recreation vehicle's load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading the vehicle. Do not exceed your GVWR and ensure you are loading the vehicle as evenly as you can for the best possible handling. Ensure heavy items are secured so they do not shift during travel.
Store items in areas designated for storage. Do not store anything in the areas reserved for the converter, electrical panels, furnace or water heater, etc.
For traveling safety, it is important to make sure the tie down straps are secured on all appliances such as the toaster, coffee maker, etc. Vibration during travel will move the appliances, creating the potential for them to fall out of their cabinets possibly causing injury.
Trailer Plug
If you choose to tow behind your RV, a chassis manufacturer supplied 7-way trailer plug (located at the hitch) is pre-wired into your motor home. Before hitching up to a trailer, please read Using the Rear Hitch, vehicle weight ratings, etc. Your motor home may have both 4-way and 7-way trailer receptacles.
Wiring to operate your towed vehicle brakes must be the same size in both the towed vehicle and the motor home.
Maintenance Record
Table of Contents
29
Section 3: Pre-Travel Information
White 1 Blue 2 Green 3 Black 4 Red 5 Brown 6 Yellow 7
Ground Electric Brakes Running lights House batteries charge line Stop & left turn Stop & right turn Back up Lights
The connector plug may build up corrosion with extended use. It should be cleaned periodically to insure good electrical contact. Make sure the connector plug is kept clean and protected from road elements as you travel.
NOTE: A 12V circuit tester is recommended to verify trailer connections.
Weighing Your Motor Home
When your motor home is loaded you should have it weighed. The actual weight of the motor home, passengers, all options, liquids, the hitch weight of your towed vehicle and your personal cargo is important for you to know so you do not exceed the GVWR. There are two important factors when loading your motor home, total weight and balance.
It is imperative that you verify compliance within all applicable weight ratings. Overloading your motor home will void the Limited Warranty and the warranties of many component part manufacturers.
Periodically weigh your motor home at a public scale to determine proper load distribution. To obtain the side-to-side weights, there needs to be enough space on either side of the scale to accommodate the motor home being partially off the scale.
Different types or scales may require different procedures when weighting the motor home. The motor home must remain as level as possible on the scale (even if an axle is not physically on the scale). To obtain the side-to-side weights, make sure there is enough space on either side of the scale to accommodate the motor home being partially off the scale.
If a boat, trailer or other vehicle is being towed, it should be weighed separately. Combine this weight with the motor home's Gross Vehicle Weight (GVW) to ensure the total combined weight does not exceed the GCWR.
Once actual weights are obtained, compare them to the Weight Information Label weight ratings to ensure you are below the posted minimum ratings.
If there is a difference in the weights on one side of the vehicle as compared to weights on the other side, components (tires, wheels, brakes, springs, etc.) on the heavier side may be overloaded, although the total axle load is within the GAWR.
It is important to redistribute the load to avoid component failure as well as to improve the handling characteristics of the vehicle.
30
Maintenance Record
Table of Contents
Section 3: Pre-Travel Information
Dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight. Full tanks can affect your fuel consumption, and depending on tank location, can affect your vehicle handling characteristics. If you cannot immediately empty your holding tanks, reduce your vehicle speed until you reach a dumping station.
See the Weight Terms and Loading Your RV sections for important information on how towing a vehicle affects the motor home weight.
Maintenance Record
Table of Contents
31
Section 3: Pre-Travel Information
Notes:
32
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Vehicle Operation
Your motor home will travel safely and comfortably at highway speed limits. However, it will take longer than a passenger automobile to reach that speed. Allow more time to go around the vehicle you are passing. Avoid situations that might require sudden momentum changes as the length of the motor home affects your ability to quickly cut back into traffic. Swerves and sharp turns, especially at high speeds, could result in loss of control of the motor home. The motor home has a longer turning radius. When turning, check the road clearance and be aware of others, especially if towing a vehicle behind your motor home. Adverse weather conditions and extremes in terrain may affect the performance and handling of your vehicle. Do not operate the cruise control on icy or extremely wet roads, gravel roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained. Use care when accelerating or decelerating on a slippery surface. Abrupt speed changes can cause skidding and loss of control.
NOTE: CALIFORNIA TIRE CHAIN NOTICE: YOUR MOTORHOME MAY NOT BE OPERATED WITH TIRE CHAINS
Braking and Stopping Even though your motor home is equipped with brakes designed for its Gross Vehicle Weight Rating (GVWR) we suggest you practice stopping away from traffic until you become accustomed to your motor home's stopping distance. Your motor home is equipped with a third brake light that activates when the brakes are engaged. When descending a long hill, shift the transmission into a lower gear and engage the auxiliary engine braking. If your motor home is equipped with an auxiliary engine brake, engagement is activated by a switch on the driver's console. See the chassis owner's manual for additional information. The transmission and engine will help in controlling downhill speed and can lengthen brake life. The distance required to stop the motor home is greater than an automobiles. Driving through water deep enough to wet the brakes may affect stopping distance or cause the vehicle to pull to one side. Check the motor home's brake operation in a safe area to be sure they have not been affected. Never operate any vehicle if a difference in braking efficiency is noticeable.
Your motorhome chassis braking system is rated for operation at GVWR not GCWR.
Parking Brake The parking brake should be engaged when the motor home is parked. Never drive your motor home with the parking brake engaged as this will reduce braking effectiveness and cause excessive driveline wear. Refer to your Chassis guide for more information on the parking brake.
Maintenance Record
Table of Contents
33
Section 4: Vehicle Operation
Using The Rear Hitch
Do not install a frame equalizing type hitch on your motorhome.
Towing will affect vehicle handling, durability and fuel economy. Exceeding any of the listed weight ratings will result in unacceptable overall vehicle performance. Your safety and satisfaction require proper use of correct equipment. For maximum pulling load and vertical tongue weight, refer to the label located on the rear hitch. A hitch bar of appropriate strength and steel should be selected to meet the capacities of the towing receptor. Always use safety chains between the motor home and the towed trailer or vehicle. Cross the chains under the tongue and allow for slack when turning corners. Connect the safety chains to the vehicle frame or hook retainers. Never attach the safety chains to the bumper. Before descending a steep or long grade when towing a trailer or vehicle, reduce speed and shift the motor home into a lower gear to control vehicle speed. Avoid frequent or prolonged brake application, which can cause overheating or brake failure. By definition the GCWR is "the maximum total weight rating allowed for a vehicle and any attachment, such as a trailer or towed vehicle. To determine the total allowable weight for a towed item, subtract the GVWR from the GCWR.
Towing and Braking Label
Total weight of your motorhome and any trailer or vehicle towed by it must not exceed the GCWR. Do not assume that you can tow a vehicle that happens to be within the capacity of the hitch. By doing so,
you may exceed the total GCWR of the motorhome.
The total weight of your motorhome (including cargo, passengers, fluids, etc...) in addition to the vertical (tongue) weight must not exceed the GVWR and/or any GAWR. Once again, do not assume that you can tow a trailer or vehicle that happens to be within the vertical
(tongue) weight capacity of the hitch. By doing so, you may exceed the
GVWR and/or GAWR of the motorhome.
Your motorhome chassis breaking system is rated for operation at GVWR, NOT GCWR. Any trailer or vehicle being towed by your motorhome must have adequate brakes as required by all state (or province)
and local regulations for towing with your motorhome, including areas you may be traveling through. Failure to follow the towing guidelines may result in property damage or injury.
34
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
In addition, a separate supplemental braking system must be installed if the towed trailer or vehicle meets or exceeds the minimum weight determined by the chassis manufacturer (this minimum weight rating will vary by chassis and chassis manufacturer). Contact your dealer for assistance in determining whether a separate braking system is recommended for your towing and traveling safety. Failure to follow these instructions will create a safety hazard and may result in an accident.
Maintenance Keep the hitch clean along with your general frame maintenance.
At the beginning of the season, and monthly or thereafter, clean the inside of the receiver tube with a wire brush and spray with a silicone spray.
Always remove the utility mount from the receiver when it is not in use. This will help prevent the utility mount from rusting to the tube.
Periodically check the bolts for tightness. They need to be torqued to the proper setting (refer to your Chassis Guide).
Refer to the Trailer Plug section for information on the trailer plug hook-up.
Power Entrance Step
The electric door step opens automatically when the screen door is opened. Constant 12-volt power to the electric step is supplied through a circuit breaker.
LOOK BEFORE ENTERING OR EXITING YOUR MOTORHOME! When opening the door from the outside, make sure you are not obstruct-
ing the path of the entrance step. Step deployment takes approximately two seconds. Keep hands and fingers clear while extending or retracting. Look before you exit. Make sure the steps are fully deployed before exiting the motor home. Stepping on a partially extended step can cause damage to the step frame.
Entrance Door
Always hold onto the entrance door when opening or closing it. Damage caused because you failed to do so is not covered by the Limited Warranty.
Make sure the entrance door is completely closed and locked when traveling. Locking the door helps prevent it from opening unintentionally and keeps intruders from your recreation vehicle.
The entrance screen door may be equipped with a slide panel that allows access to the entrance door handle and locks. The entrance door may also be equipped with both a regular door lock and a dead bolt lock.
Keys Several keys are provided when you purchase your vehicle. Most keys have an individual key number stamped on the plate. Record these key numbers and keep the information in a safe place. You can order a key blank from your dealer to have duplicate keys made. If you lose the keys, contact your dealer or a locksmith for assistance.
Maintenance Record
Table of Contents
35
Section 4: Vehicle Operation
NOTE: Locks on entrance and baggage doors need biannual lubrication using a light coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the maintenance needs.
Driver and Passenger Seat
Do not adjust the seat while driving. After adjusting the seat, make sure that it is locked in position. To ensure that the seat is locked securely, try to move the seat forward or backward without using the adjusting lever or button. Do not put packages, pets or other objects between the driver's and front passenger co-captain's seat.
If equipped with reclining seats: to minimize the risk of personal injury in the event of a collision or sudden stop, always keep both the driver's captain and passenger co-captain seat backs in a nearly upright position while the motor home is moving. The protection provided by the seat belts may be reduced significantly when the seat back is reclined. Reclining the seats while the motor home is moving may result in serious injury.
If equipped with power seats: keep hands and feet clear of the power seat while in operating the power feature.
NOTE: The driver's and front passenger seat must be locked in the forward facing position while the motor home is in motion.
6-Way Power Seat (if so equipped) Use the controls to slide the 6-way power seat to the desired position. Release the control, and the seat will lock at that position. Features may include a 3-point adjustable seat belt, lumbar support, swivel, slide and reclining capabilities. (Not all of these features will be available in all motor home models). To rotate the driver/passenger seat (if so equipped) To face the driver or front passenger seat toward the rear of the vehicle, pull the seat swivel release lever up and rotate the seat. To return the seat to the original position, rotate seat back to the driving position until you hear a click and the seat locks into position.
36
Maintenance Record
Table of Contents
Seat Belts
Section 4: Vehicle Operation
Seat belts should always be worn by anyone who drives or rides in this vehicle. Never use one seat belt for more than one occupant. Never carry more
people in the motor home than there are seat belts. Only seats equipped with seat belts are to be occupied while the vehicle
is in motion. While traveling, do not occupy beds or any seats that do not have seat belts. Be sure to lock all doors before driving. Locking the doors and using the provided seat belts will minimize the risk of injury or ejection in an accident. If you are pregnant, consult your health care professional for advice on seat belt use.
Always use seat belts. In an accident, injury to the driver and passengers may be reduced if seat belts are properly used. If your motor home is equipped with a booth dinette, hide-a-bed sofa, or easy bed sofa they will have two-point lap-seat belts installed. Seat belts should be used in all seating positions.
Maintenance and inspection of seat belts The webbing used in seat belts may be cleaned with a mild soap or detergent solution. Allow the belts to dry in the shade and do not allow them to retract until fully dry.
Regularly check the seat belt buckles and release mechanisms for positive action and check automatic locking retractors for positive engagement.
If the seat belt webbing shows obvious cuts, protruding broken fibers or severe fading which indicates weakening by exposure to sunlight, the entire seat belt assembly should be replaced. Do not try to bleach or re-dye the belts. The resulting color may rub off and the webbing strength could be affected.
Child Safety Restraint Systems
When transporting infants or small children, an appropriate child safety restraint system should always be used. Follow the manufacturer's instructions for the correct installation and use of these systems.
NOTE: All child safety restraint systems should always face the front or rear of the motor home. They should never be installed so the occupant is facing the side of the motor home.
Maintenance Record
Table of Contents
37
Section 4: Vehicle Operation Vehicle Dash
Do not set anything on, or attach anything to, the instrument panel or dash. Do not attach anything to the steering wheel cover. Failure to follow these warnings may restrict the driver's visibility or cause an object to strike and injure an occupant in the case of a collision or sudden stop.
Maintenance To clean the vinyl/ABS dash, soak a soft cloth in a solution of mild detergent and water. Wipe off the dash. To rinse, dip a cloth in fresh water and wring it out well. Wipe off the detergent thoroughly.
Outside Rearview Mirrors
Adjust the outside rearview mirrors before driving.
After adjusting the front driver's seat, adjust the outside rearview mirrors to your driving preference. Have someone help you adjust the mirrors in the desired direction for maximum rear visibility before driving. During travel, vibration may loosen the fitting holding the mirror(s), causing them to change position. As part of your regular motor home maintenance, check and adjust the mirrors to the desired position.
Power Remote Mirrors (if so equipped) You can adjust the power remote mirrors when the ignition key is in the ON position.
1. Move the control knob to the side you want to adjust. 2. Press the control arrows in the direction you want the
mirror to move. 3. Return the control knob to the center to lock the mirror(s)
into place.
Remote Mirror Control / Mirror Heat Control
(appearance may vary by model)
The power remote mirrors also contain heating elements to defog or de-ice the mirrored
glass if needed. To activate this feature, use the "Mirror Heat" control located on the driver's
side console next to the mirror control joystick.
NOTE: Depending on models, the mirror control joystick and the Mirror Defrost toggle switch may be separated from each other. The Mirror Defrost switch may be renamed Mirror Heat.
38
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Rear Vision Camera
The rear vision monitor gives a limited televised view of what is behind your motor home. The rear vision camera will aid you in backing up the motor home, and can be used for a greater field of vision when driving in heavy traffic. Your RV may also be equipped with side view cameras mounted in the mirrors or on the body of the motor home (facing rearward) to give you views down each side of the motor home. Check the outside rear view mirrors when driving and backing for a more complete field of vision. The monitor is operational whenever the engine is running. To use the monitor, flip the switch from standby to ON (the monitor will also work when with the motor home is in "reverse" and the monitor in standby). Make sure you turn the monitor to standby while driving to avoid being distracted. Never operate the rear vision monitor in the ON position for extended periods of time as this may result in an "image burn" on the monitor. For detailed operating and safety information, refer to the manufacturers user guide.
Camera/monitor system aids in the use of, but does not replace vehicle side/rear-view mirrors.
Objects in camera/monitor view are closer than they appear. When backing up, proceed cautiously and be prepared to stop.
Campsite Hook-Up
Refer to Electrical Systems section before connecting the shore line power cord (when using full hook-up) OR before starting the generator (if so equipped) or operating the vehicle on 12-volt power when dry camping.
Refer to Fuel & LP System section before using the LP system. Open the LP gas tank valve (if so equipped) slowly. There may be air in the lines and five to thirty seconds of time is needed to bleed air before LP vapor fills the lines.
Refer to Plumbing Systems section before connecting the fresh water supply or turning ON the water pump or water heater.
When using full hook-up, connect the sewer hose to the campsite sewer hook-up. If applicable, start the refrigerator and the cooling or heating system.
NOTE: For extended dry camping, management of all your resources is essential. Check your battery levels and conserve battery power, use it sparingly
Maintenance Record
Table of Contents
39
Section 4: Vehicle Operation
Hydraulic Leveling System
FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING WARNINGS MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH! The leveling system is designed only for leveling the unit and should
never be used to provide service for any reason under the motor home such as changing tires or servicing the system. It is not recommended that you change a tire yourself. Check that potential jack contact locations are clear of obstructions or depressions. Keep people clear of the motor home prior to turning the leveling system on and while the leveling system is in operation. Never expose hands or other parts of the body near hydraulic leaks. Highpressure oil leaks may cut and penetrate the skin causing serious injury. After starting the leveling cycle, it is important that occupants do not move around in the motor home until the vehicle is level. Failure to remain still during the leveling cycle can affect the leveling jack system sensors. Never lift the wheels off of the ground when leveling the motor home. Do not move the motor home while the jacks are still in contact with the ground or extended. Damage to the vehicle could occur. Do not rely solely upon warning lights to determine the position of the leveling jacks. It is the operator's responsibility to check that all the leveling jacks are fully raised in the travel mode before moving the motor home.
For detailed operating and safety information, refer to the manufacturer's user guide.
Leveling your motor home is important for the following reasons The water drainage systems are designed with proper slope and must be level for proper operation. The appliances perform best when level.
Before operating the leveling system, the motor home: Must be parked on a reasonably level surface. Must have the parking brake engaged. Must have the transmission gear selector in NEUTRAL. Engine should not be running
NOTE: The slideout room should be extended (with the air suspension fully aired up) before leveling jacks are deployed. Wheels MUST be straight. When the coach is leveled, air bags are dumped of air which lowers the fenders below the tops of the wheels. If the wheels are not straight, fenders and/or tires WILL be damaged. DO NOT DUMP AIR FROM AIR BAGS UNLESS WHEELS ARE STRAIGHT!
40
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Operating the Leveling System Auto Leveling Operation
Baseline Zero Point Calibration: "Baseline zero point" is the term used to define the point at which the motor home interior floor is level in the "X" and "Y" plains. The base line zero point has been preset from the factory. If the coach is not level following an attempt to auto level, you will need to reset the baseline zero point.
Setting the baseline zero point
NOTE: You do not need to have jacks deployed to set the baseline zero point.
1. Push and release the POWER keypad button to engage power. The LED next to the POWER button should be RED when power is on.
2. Level the coach by deploying jacks manually (using the DOWN keypad button, extend each jack until the coach is level) or by parking the coach on a level site.
3. Use a bubble level on a flat surface in the center of the coach as a reference. 4. Level the coach in both the "X" and "Y" plains (fore-aft and side to side). 5. Once level, turn the POWER off at the panel. 6. Depress and hold the AUTO-LEVEL keypad button. 7. Continue to hold the AUTO-LEVEL button and press and release the POWER button
and listen for a series of beeps. 8. After the panel has beeped 5 to 6 times, release the AUTO-LEVEL button (the keypad
will continue to beep as long as the AUTO-LEVEL button is held). The new baseline zero point has been set and the panel will maintain this setting. 9. Press and release the ALL RETRACT button to retract the jacks to the stowed position. Power On: Push and release the POWER button to engage power. The LED next to the POWER button should be RED when power is on. You will need to have the ignition key in the "off" position to extend the jacks. If you attempt to extend individual jacks by pressing the ON button or all jacks with the AUTO-LEVEL button, you will hear a "deny" tone from the keypad. Auto Level: Press the AUTO-LEVEL button and release. The system will send
out a continuous series of beeps, the "OPERATING" LED will flash RED to let you know auto level is operating and will automatically level the coach. When completed, the keypad will signal a successful level with a dual-level tone. The keypad may be left on once level has been achieved. The keypad will enter "sleep mode" after five minutes of inactivity. Retracting the Jacks: The Equalizer System provides the ability to retract the jacks using the ALL RETRACT button or the UP button for each individual jack. All jacks will automatically retract and return to stowed position when the ALL RETRACT button is pressed and released. The pump will run in retract mode for 60 seconds (or 90 seconds, depending on your specific system) to ensure the jacks are fully stowed. You may allow the system to run for the entire programmed time and stop automatically, or you may stop the ALL RETRACT by pressing any button on the keypad.
Maintenance Record
Table of Contents
41
Section 4: Vehicle Operation
Manual Operation Power on: Push and release the POWER keypad button to engage power. The LED next to
the POWER button should be RED when power is on. If you attempt to extend individual
jacks by pressing the DOWN keypad button or all jacks with the AUTO-LEVEL button, you
will hear a "deny" tone from the keypad.
Planting the Jacks: Using the DOWN keypad button, extend each jack until they contact the ground (this is referred to as "planting" the jacks).
As you extend the jacks, the LED lights on the keypad will indicate the jacks are out of the "stowed" position. Jacks may be operated individually or in pairs.
Do not manually overextend individual jacks. This may cause unwanted stress on the coach or the jacks.
Leveling the Coach: Use a bubble level in the center of the coach as a reference. Level the vehicle by using DOWN or UP keypad buttons until the vehicle is level. Jacks may be operated individually or in pairs as long as they are operated in the same direction.
Do not attempt to lift the vehicle off of the tires. The keypad may be left "on" once
level has been achieved. The keypad will enter "sleep mode" after five minutes of inactivity.
Hydraulic Control Panel
Retracting the Jacks: The Equalizer System provides the ability to retract the jacks using the ALL RETRACT button or the UP button for each individual jack. All jacks will automatically retract and return to stowed position when the ALL RETRACT button is pressed and released.
The pump will run in retract mode until all of the jacks are fully stowed (plus an additional 5 seconds) up to a maximum of 60 seconds. You may stop the ALL RETRACT by pressing any button on the keypad. Your coach is equipped with air suspension, and it is recommended that you start your coach before pressing ALL RETRACT allowing the chassis air to build. This will ensure adequate air supply to the chassis air valves.
NOTE: There are specific instances when manual extension of one (or more) jack is inhibited (deny tone when DOWN is depressed). This situation is caused by the "anti-twist" protocol in the software contained in the
control box. The "anti-twist" protocol denies jack extension if the system senses that a specific corner of the coach is approximately 3 degrees higher than the rest. You will be able to extend other jacks to overcome this slope. If the system incorrectly senses excessive slope, this can be overcome by re-setting the baseline zero point. This will allow manual extension of all jacks. Remember to re-set the baseline zero point
after manually leveling the coach.
42
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Helpful Hints The ALL RETRACT function is a timed event. Pressing ALL RETRACT will cause the pump to run in retract mode for 60 seconds (or 90 seconds, depending on your specific system). Your leveling system is a microprocessor-controlled system. Proper and adequate battery voltage and permanent chassis ground are essential. Your system may be equipped with a manual override option. Refer to the procedure for proper operation of this option. It is better to review this procedure prior to its actual use. If a jack comes out of the stowed position while traveling, the system panel will automatically activate and return the jack to the stowed position.
Panel Indicator LED There are a total of ten (10) LED indicators on the Equalizer Keypad. The functions of these indicators are detailed below.
If the LOW VOLTAGE, ENGAGE PARK BRAKE, IGNITION ON or EXCESS SLOPE LEDs illuminate, you have an "error" condition that must be corrected prior to operating the jacks.
Make sure suspension air bags have deployed after retracting jacks. Visually check front and rear wheel wells for clearance.
During typical operation, the LEDs on the bottom left hand corner of the keypad
should NOT be illuminated. The only LED that should light is the "OPERATING"
LED, which should flash during operation.
POWER LED
ON Red when power is ON
OFF when power is OFF
FLASH every 5 sec. in Sleep Mode
JACK LED (4 each)
ON Red when Jack(s) are deployed OFF when jack(s) are stowed
OPERATING LED FLASHING Red w/Auto Level or All Retract OFF when keypad is idle or "sleeping"
LOW VOLTAGE LED
ON Red when voltage is below 10.5 volts dc OFF when voltage is above 10.5 volts dc
ENGAGE PARK BRAKE LED
ON Red when park brake is not set OFF when park brake is set
IGNITION ON LED
ON Red when ignition is in the ON position OFF when ignition is OFF
EXCESS SLOPE LED
ON Red following an Auto Level attempt, if system cannot overcome slope
OFF when slope is not excessive
For complete instructions, troubleshooting and safety information refer to the manufacturer's manual online at https://equalizersystems.com/service-and-support/operation-andinstallation-manuals/
Maintenance Record
Table of Contents
43
Section 4: Vehicle Operation
Emergency Stopping
Always carry road flares or reflective warning signs. Pull off the roadway as far as possible for emergency stopping. Turn ON your vehicle hazard warning flashers. If traveling at night, use three red warning indicators such as flares, reflectors or lanterns as required by the Uniform Vehicle Code and Model Traffic Ordinance as follows: 1. Place the first warning indicator on the traffic side of the recreation vehicle, directed at
the nearest approaching traffic. 2. Place the second warning indicator 100 feet behind the recreation vehicle in the center
of the lane and toward approaching traffic. 3. Place the third warning indicator 100 feet in front of the recreation vehicle in the center
of the lane and away from the traffic approaching from behind.
NOTE: Curves and/or hills may affect the safe placement of warning indicators.
For personal safety, always stand off the road and out of the way of traffic.
Emergency Towing
If your motor home ever needs to be towed, refer to the instructions in your Chassis Guide. Please contact an emergency road service provider or a qualified service facility for assistance, Make sure the road service technician reads and is familiar with the information contained in your Chassis Guide regarding emergency towing.
Never allow anyone to go under the motor home while it is being lifted by towing equipment.
Be aware of the strap locations. Misplaced straps could result in damage to the exterior of your unit. Damage resulting from misplaced straps is the responsibility of the towing company, and is not covered by the unit warranty
Front Axle Tire Alignment
The term alignment refers to both the adjustment angles on the steering axle and suspension and tracking of the rear axle. Steering components, suspension, wheel bearings and even proper loading will affect the alignment. We recommend you have the front suspension and steering alignment checked and adjusted after you have fully loaded the vehicle as part of the vehicle maintenance. Thereafter, it is your responsibility to have the alignment inspected periodically to maintain vehicle steering performance and prevent uneven tire wear as part of your normal maintenance.
44
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
NOTE: Always have the alignment checked and adjusted by a qualified shop with the proper equipment to handle heavy vehicles.
NOTE: A road test by the dealer should be included as part of the pre-delivery inspection. The dealer can check for and correct any steering problems before you take delivery.
After this road test has been completed, front-end alignment and/or vibrations will not be covered as part of the new vehicle limited warranty. Follow the Chassis Guide maintenance instructions for the front and rear axle for wheel and suspension maintenance, including the brakes and wheel bearings. Contact your Chassis manufacturer for assistance.
Wheel Lug Nuts/Wheel Liners
Check and tighten the wheel lug nuts regularly to ensure they did not loosen during travel. Refer to your Chassis Guide for torque recommendations.
Failure to tighten and maintain wheel lug nuts to the proper torque specification, could allow the wheels to come off while driving, resulting in serious injury or property damage in the event of a collision or loss of vehicle control.
Torque is the amount of rotating force applied to a lug nut, and can only be achieved by using a properly calibrated torque wrench and socket. Do not use a 4-way socket or any other type of wrench that does not measure the actual pressure applied to the lug nut.
NOTE: The proper method of tightening wheel lug nuts is with a torque wrench, not with an impact wrench or by hand. Because of the importance of having proper torque on the wheel lug nuts, you should always have the wheels mounted and properly torqued by a qualified technician using the proper tools.
After your first trip, check the wheel lug torque periodically for safety according to your Chassis Guide. If you suspect the wheel lug nuts have loosened at any time, have them checked and torqued to the proper limits immediately. Lugs should be checked after winter storage, after a wheel removal, before starting a trip or following extensive braking. Refer to the Wheel Lug Torque Chart.
Maintenance Record
Table of Contents
45
Section 4: Vehicle Operation
Check and re-torque after the first 10, 25 and 50 miles (16, 40 and 80 kilometers). Thereafter, check and maintain the torque according to the listed torque values. Wheel Lugs If you suspect or notice the wheel stud bolts are cracked or broken, they must be replaced, along with adjacent bolts that have probably also been weakened due to the additional stress placed on them. Aluminum Wheels (if so equipped) Clean the aluminum wheels with a cleaner that is designed for use on aluminum and apply an appropriate protection agent. Do not use abrasive cleaners. Wheels exposed to sea water or road chemicals should be cleaned as soon as possible. Be sure to use a sponge or chamois leather (brushes may damage the aluminum wheel surface).
NOTE: If your motor home is equipped with aluminum wheels, only the outer dual wheels are aluminum, the inner duals are steel wheels.
Tires
Read and understand the following before taking your first trip in your RV. Routine maintenance on your RV is important. To ensure your tires are operating safely, regular inspection of the tires and checking tire pressures is absolutely mandatory. Alignment, balance and bearing wear will affect tire wear. Make sure to look for cracking, bulging, uneven tread wear, etc.
46
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is corrected.
Tire pressure
Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death.
You must follow the manufacturer's inflation guidelines for maximum load capacity; under-inflation is just as dangerous as over-inflation. Proper inflation should be monitored closely. Failure to do so could result in the overheating of a tire causing a blowout. Inflation pressure should be as recommended by the tire manufacturer or as the federal label for the recreation vehicle indicates. When you are using your Recreation Vehicle, check inflation pressure weekly. Pressure should be checked when the tires are cold. During travel, tires heat up and pressure increases. Do not bleed air from hot tires or your tires may then be under-inflated.
NOTE: Cold tire inflation pressure is defined as a tire that has not been used for three or more hours, or has been driven less than one mile. Tire inflation pressure of a hot tire may show an increase of as much as 6 psi over a cold tire.
It is recommended that the tire pressure be checked at the beginning of each trip to obtain the maximum life of the tire. Follow the instructions listed on the Federal Certification label, to determine the correct tire pressure. Under-inflation may cause tire failures and swaying resulting in loss of control, injury, death or property damage.
TOWABLE PRODUCTS ONLY Towable recreation vehicles are equipped with special trailer (ST) tires
that have a maximum speed rating of 65 MPH (104 km/h). You should not exceed this speed rating. Exceeding the tire speed rating may result in tire failure, which could lead to an accident causing serious injury or death.
Maintenance Record
Table of Contents
47
Section 4: Vehicle Operation
Changing A Tire
The motor home is very heavy. Raising the motor home to replace the spare tire should only be done with extreme caution by a qualified technician. The vehicle could slip, causing personal injury or death. DO NOT ATTEMPT TO DO THIS YOURSELF.
Do not use the hydraulic leveling jack system to support the motor home while under the vehicle or changing tires. The hydraulic leveling system is designed as a leveling system only. Do not use the hydraulic leveling jack system as a jack or in conjunction with a jack. It is highly recommended that, should a tire change be required, it be performed by a knowledgeable, trained professional. Attempts to change tires while supporting the motor home with the hydraulic leveling jack system could result in damage to the motor home and risk causing serious injury or death.
When replacing a tire, make sure to replace it with a tire of the same size and specifications (refer to your Chassis Guide for assistance).
If you experience a flat tire on your motor home while driving, gradually decrease your vehicle speed (if possible), and move the motor home to a safe place on the side of the road. Contact your road service provider (if applicable) or a qualified service facility for assistance. Do not attempt to change the tire or jack the motor home up yourself; this is why a jack and a spare tire have not been included with the motor home. Make sure the road service technician reads and is familiar with the Chassis Guide information regarding changing the tires. Make sure the wheel lug nuts have been tightened to the proper torque as outlined in your Chassis Guide.
Awnings (if so equipped)
Awnings must be closed (and locked if applicable) while the RV is in transit.
The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. Retract the awning:
If wind or extended periods of rain are expected If you leave the RV unattended for a length of time, to avoid unexpected
climate conditions.
Awning Care Keep your awnings clean and in good condition to prevent costly repairs.
Periodically check that the fasteners are tight. Tighten if necessary. Keep the awning fabric clean. For detailed cleaning information, refer to the
manufacturer's owner information.
48
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Your recreation vehicle may include one or more of the following options: Power window awnings Slide out awnings Power awning over entrance door
Power switches to operate the awnings are typically found in the control panel above the entrance door or if your RV has a touchscreen, the awning controls may be located there. Electric Patio Awning with Remote Control
NOTE: Most electric awnings requires connection to a 120-volt power source. Make sure you have sufficient power available before operating your awning (refer to Electrical Systems, Calculating electrical load).
In Motion Detector (if so equipped) Some patio awnings are equipped with a motion detector. If the patio awning experiences extreme or excessive movement, it will automatically retract to the travel mode position. For detailed safety and operating information, refer to the manufacturer's user guide. Girard Awnings (if so equipped) refer to the manufacturer's owner manual located on a CD and USB flash drive included in your warranty packet. This manual includes troubleshooting, service and repair information.
Power Awnings (if so equipped)
Your recreation vehicle may be equipped with a power awning. Refer to the manufacturer's manual for additional safety and operating information.
Awnings must be closed (and secured) while the RV is in transit. Keep clear of arm assemblies while opening, adjusting or closing the aw-
ning. Failure to obey this caution could result in injury and/or property damage. Always operate the awning according to the instructions. Periodically check that the fasteners are tight (tighten if necessary). Keep the awning fabric and arms clean.
The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. If wind or extended periods of rain are expected, retract the awning.
It is recommended that if leaving the recreation vehicle unattended for a length of time you should retract the awning to avoid unexpected weather conditions.
Each power awning will have its own control switch. Pressing and holding the switch will extend or retract the awning. The awning should automatically stop when the switch is released.
Maintenance Record
Table of Contents
49
Section 4: Vehicle Operation
NOTE: Do not overextend the awning. If the awning or awing skirt show signs of overextending, retract the awning until it is in the appropriate position.
Most power awnings give you the ability to adjust the awning pitch (slope). This will help with water runoff and pooling. When adjusting the awning scope, be aware of entrance door and window clearances. Coming into contact with a door or window can damage or tear the awning fabric.
Before retracting the awning, make sure there is not pooled water or debris on the awning.
When preparing to travel, make surecompletely retracted and secured. Turn off any light strips (if applicable).
For motorized products, test the system with the ignition ON to make sure the awning is disabled for transit.
Most power awnings have a manual override in the event the awning will not retract. Refer to for detailed on the manual override. Maintaining the Awning
Do not use insecticides or other sprays near the awning fabric. These can cause stains, and could adversely affect the fabric's ability to repel water.
Do not expose the awning to adverse environmental conditions, corrosive agents, or other harmful conditions.
Do not allow the corner of the entry door to contact the awning fabric. Otherwise, premature wear or tearing of awning fabric could occur.
Never close the awning (for storage) when wet. The combination of moisture and dirt could result in mildew, discoloration, and stains. If it is necessary to roll up awning (temporarily) while it is wet, make sure you roll it out and let it dry (as soon as conditions allow) before rolling it up again.
Do not allow dirt, leaves, or other debris to accumulate on the awning, which could cause abrasion and stains. Mildew could grow on dirt and organic debris, causing permanent discoloration, stains, and odors to the awning fabric.
Do not use strong chemicals or abrasives to clean parts, as their protective surfaces will be damaged. Clean awning hardware (as needed) with a mild surface cleaner.
Apply silicone spray lubricant as needed to the moving parts on the fabric roller tube assembly.
Lubricate all pins and sliding surfaces of the arm assemblies with silicone spray, as needed.
Do not use abrasive or corrosive cleaners, mildew removers, or hard bristle brushes on the awning fabric.
Vinyl awning fabric is durable and water resistant. Wrinkling is a normal characteristic, which may be more noticeable when the awning is retracted, and after prolonged periods of stowage (rolled up).Leaveopen during warm weather to minimize wrinkling. A slight "travel line" may appear where the door roller (if installed) contacts the fabric. This is normal and does not affect the integrity of the fabric.
To clean the fabric: Open the awning. Mix 1/4 cup dish soap and 1/4 cup bleach with five gallons of fresh water. Liberally drench the fabric with cleaning solution.
50
Maintenance Record
Table of Contents
Section 4: Vehicle Operation
Close the awning and allow the cleaning solution to soak for five minutes. Open the awning and thoroughly hose off the top and bottom of the fabric with
clean water. Repeat if necessary. Remove the solution COMPLETELY from the awning fabric. Bleach will degrade
the fabric if it is not completely rinsed off. Make sure the fabric is dry before closing the awning.
Maintenance Record
Table of Contents
51
Section 4: Vehicle Operation
52
Maintenance Record
Table of Contents
Section 5: Slideout Systems
Electric Slide Room(s) (if so equipped)
The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss. Make sure you have sufficient power available before operating your slideout system. Level the RV prior to extending the slideout. Slideout switches are typically located inside the RV, either in the command center or on the wall. If your RV is equipped with a touch screen control system, your slide room controls will be built into the touch screen system.
Make sure the interior slideout room path and the slideout room itself is clear of people and objects before operating.
Keep away from the slide rails and gear assembly when the room is in motion. They may pinch or catch on loose clothing causing personal injury.
Failure to follow these instructions could result in serious injury or death
These guidelines should be followed when using your slideout room:
Make sure the slideout is in the closed position prior to hooking the unit to the tow vehicle.
The recreation vehicle must be level before operating the slideout room. Water leaks and other problems could result if the slideout is operated without leveling the RV.
Do not place excessive weight in the slideout room. It can cause the slideout room to malfunction and cause damage to the slideout.
Do not over extend/retract the slide out room. Release the switch immediately once the room has been fully extended/retracted. Over extending/ retracting the slide out room may result in damage to the stop rod and bracket.
Additional support jacks are not needed under the slideout. Damage can occur to your slideout room from improper use of aftermarket support jacks.
General Slideout Operation The auxiliary battery (customer supplied) must be fully charged and connected. If possible, the RV should be hooked up to 120-volt AC power so the converter operates. The RV must be level and the stabilizer jacks in the extended position. Slideout switches are typically located inside the RV, either in the command center or on the wall. To extend the slideout, locate the slideout control switch and press the OUT section of the switch; hold until the slideout room stops (travel time is approx. 25 seconds).
Maintenance Record
Table of Contents
53
Section 5: Slideout Systems
To retract the slideout, press the in section of the slideout control switch and hold it until the slideout is fully retracted.
Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstructions. If the slideout is equipped with rubber seals, verify that the corners of the black rubber seal are set up correctly. The seal corners are cut at a 45° angle. The top of the outside seal must overlap the side of the seal to avoid the possibility of water penetration. On the inside seal, the side seal should overlap the top.
NOTE: For long-term storage it is recommend the room be closed (retracted).
General Slideout Troubleshooting Checklist
NOTE: For additional troubleshooting information, refer to the specific slideout system detail.
If the slideout does not move when the slideout switch is depressed, follow these steps: Check the auxiliary battery (customer supplied) for a full charge and good wire connections. Check the 12-volt fuse or circuit breaker. Check for loose connections at the slideout motor.
If the slideout still will not operate, follow these steps: If the slideout is extended, refer to the section on operating the specific slideout system installed on your RV. If the slideout is retracted, leave it in that position.
If the slideout extends crooked or only one side moves: Follow steps on overriding the specific slideout system installed on your RV. You may need to push the side that is not sliding to get it to retract all the way.
Contact your dealer or customer service for repair assistance. Slideout Systems Your RV may be equipped with one or more of the following slideout systems. Flush Floor Slideout For optimum performance, the slideout system requires full battery current and voltage. Although the system is almost maintenance free, actuate the room once or twice a month to
54
Maintenance Record
Table of Contents
Section 5: Slideout Systems
keep the seals and internal moving parts lubricated. Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. Electric Operation
NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.
Extending/retracting the room 1. Level the unit. 2. Main Power switch at stepwell (locations may vary) must
be ON. 3. Verify the battery is fully charged and hooked up to the
electrical system. 4. Remove the transit bars (if so equipped) if extending the
slideout, and install them if retracting the room for travel. 5. Press and hold the IN/OUT switch in the OUT position until the room is fully extended
and stops moving. Hold the switch in the IN position to retract the room. 6. Release the switch, which will lock the room into position. If the slideout switch is held
after the room is fully extended or retracted, the control will sense that the room has stopped and will shut the motor off after a few seconds. Manual Operation for the flush floor slideout Locate the crank extension under the inside of the frame (Fig. 1 and 2). Attach a standard fifth wheel landing gear crank handle, a ¾" socket and ratchet, or drill and nut driver. Rotate the extension clockwise to retract the slideout and counterclockwise to extend it. DO NOT attempt to disengage the motor as the actuator is "manual ready".
Always disconnect battery from system prior to manually operating system. Failure to disconnect battery can cause electricity to back feed through the motor and cause serious damage to the system as well as void the warranty
Use EXTREME CAUTION when extending/retracting the room using the manual override feature. The gears can be stripped out if the room is manually retracted/extended to its fullest extent and the operator continues to rotate manual override. Damage can also occur to the slide components, slide room structure or trim components. Damages due to misuse of the manual override feature will void any and all claims to the Limited Warranty.
Maintenance Record
Table of Contents
55
Section 5: Slideout Systems
Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board.Schwintek slideouts are typically used on both towables and motor homes.
NOTE: Do not operate the switch after the room is fully extended or retracted as damage can occur to the motor and/or switch.
To operate the slideout using a wireless remote (if so equipped): Press the on/off button to power on the remote. Press the corresponding button of the slideout you want to operate. Press and hold the (extend/retract) arrow button to move the room in or out. Press the on/off button once more to power off the remote.
ALWAYS allow the controller to stop both motors before releasing the switch button. DO NOT try to time the end of the stroke by releasing the button early. Maintenance
Do not work on your system unless the 12-volt DC (auxiliary battery) and 120volt AC electrical systems (shore line power cord) have been disconnected.
This slideout system requires very little maintenance. It contains a pre-lubed bearing that is lubricated when the room is moved in and out. Do not spray oil or grease on the rails while the room is extended.
56
Maintenance Record
Table of Contents
Section 5: Slideout Systems
Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replacement, there is a problem with the wiring to the in-wall slide control box. A qualified service person should be called to check and repair. Obstructions: Check both inside and outside for possible obstructions. Also check for smaller objects that may be wedged under the floor or in the sides of the unit. Remove any obstructions before proceeding. Error Codes: Refer to the error codes section for codes and instructions on how to locate the in-wall slide controller. Low Voltage: The in-wall slide controller can operate with as little as 8 volts; however, with lower voltages the amperage requirement is greater. Check the voltage at the controller and if it is lower than 11 volts, it is recommended that the battery be placed on a charger until it is fully charged. It may be possible to "jump" the RV battery temporarily to extend or retract the room. Consult Customer Service before attempting to "jump" the auxiliary battery. Only 1 Side Moving: The slide room has a separate motor to operate each side of the room. If only 1 side is moving, with another person's assistance, press the switch to extend or retract the room while pushing the non-moving side in the appropriate direction. On larger rooms it may be necessary to have 2 or more people pushing the room. Non-moving side moved manually: Try to push the non-moving side in and out. If a motor shaft has broken it will be possible to move that side of the room several inches by hand. Larger rooms may require several people to push. Debris in the rack: Check all 4 gear racks on the side of the room for debris. Status LEDs lights: Locate the slide controller for the slideout in question. Check the status LED lights while pressing the slideout direction switch (in both the extend and retract mode).
Manual override for the in-wall slideout The slideout system comes with an "electronic" manual override. In event the slide out does not extend or retract follow these steps to override the system which should allow the slideout to be retracted.
NOTE: Fuses for the slideouts can be found in the load center and may be designated as auxiliary or slideout motor.
1. Locate the slideout system controllers. There should be one for each slideout on the recreation vehicle. They are typically located on the forward wall or ceiling of a basement compartment. In some models they may be behind a cargo lined panel.
2. The malfunctioning controller should have a flashing red LED indicating a halt signal fault (will flash 8 or 9 times).
3. Press the "mode button" six times quickly, then press a seventh time and hold for approximately 5 seconds.
4. The red and green LED's will flash indicating you are in override mode. Release the mode button.
5. Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to
Maintenance Record
Table of Contents
57
Section 5: Slideout Systems
get the recreation vehicle to a service center to have the slideout malfunction diagnosed.
Call your dealer or Customer Service if: During the override procedure the motors are not synchronized. Visually
watch the room, and if one side is moving significantly slower than the other (or not at all). If the system stalls out before reaching end of stroke OR if the room does not close and seal tightly.
Manually pushing in the slideout 1. Locate the slideout system controller. 2. Unplug motor 1 and motor 2 connectors at the bottom of the slideout controller. This
releases the motor brakes for each motor.
3. The slideout room can now be manually pushed in. Larger rooms may require several people to push or pull them.
4. Keep both sides of the slideout relatively even while pushing/pulling.
5. When the room is completely in, plug both motor connectors back into the control module. This will apply the motor brakes for road travel.
Disengage motors, manually retract the room and travel lock 1. Locate and remove the motor retention screw, which can be found near the top of each
vertical column (Fig. 3). 2. Bend back the wipe seal and visually locate the motor (Fig. 4). 3. Pull the motor up until it disengages (about 1/2 inch).
4. Repeat this process for both sides of the slide room.
5. Physically push/ pull the room back into the opening; keep both sides relatively even.
6. The room must be travel locked to keep the room in place for road travel.
58
Maintenance Record
Table of Contents
Section 5: Slideout Systems
DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN TO THE CONTROLLER AND THERE IS BATTERY POWER TO THE RV. THIS SETS THE BRAKES ON THE SLIDEOUTS TO PREVENT THEM FROM MOVING DURING TRANSIT.
Error Codes When an error code occurs during operation, the board LEDs lights will indicate where the problem is. For motor specific faults the green LED will blink (1) time for motor #1 and (2) times for motor #2. The red LED will blink 2 to 9 times depending on the error code. Error codes are as follows: 2 times Battery capacity is low enough to drop below 6 volts while running. 3 times Battery (low) voltage is below 8 volts at the start of a cycle. 4 times Battery (high) voltage is greater than 18 volts. 5 times Excessive motor current (high amperage) also indicated by (1) side of the slide
continually stalling. 6 times Motor short circuit: motor or wiring to motor has shorted out. 8 times Hall signal not present: encoder not providing a signal; usually a wiring problem. 9 times Hall power short to ground: power to encoder has been shorted to ground;
usually a wiring problem. The board will need to be reset after an error code. Energizing the extend / retract switch will reset the board; energizing it a second time will return it to normal operation. Refer to the Schwintek Slide Room Operation Guide for additional troubleshooting information, or contact Lippert at (866) 5247821 or at www.lci1.com. Norco Slideout System The Norco slideout system is a cable driven slide out used typically on towable products.
The cables guide the room in or out, while the Accu-Slide mechanism evenly powers the corners keeping the room square.
Motors and cables are behind the interior fascia board around the slideout opening. Cables may stretch over time. Average stretch will be approximately 1/8" but it
will not affect the function and does not require adjustment. Slideout runs off the DC power in the RV. Rubber wipes prevent debris from entering the unit and actuation guides the bulb
seals to close tightly. Self-locking motor freezes the room in any position of travel. Slideout is supported by rollers or wear bars not the cables. Cables are used to
keep the slideout balanced on the rollers. If the room will not activate, generally there is no 12V power to the drive motor. The motor is equipped with a hex drive override shaft. This drive can be activated using an electric drill and the flexible shaft provided with each unit (or use a ratchet to actuate the motor) to pull the room in or out. If the motor is functioning, check the room for obstructions.
Maintenance Record
Table of Contents
59
Section 5: Slideout Systems
Norco Slideout Manual Operation 1. Locate the included flexible shaft in your own-
er's packet.
2. Attach flexible shaft to the 1/4" hex fitting on the end of the motor.
3. Attach 1/4" socket & ratchet, or drill to the other end, and turn in the proper direction to move the room.
4. If the cables tighten, and the motor is difficult to turn, REVERSE THE DIRECTION. OVER-TORQUEING CAN HAPPEN, RESULTING IN SEVERE DAMAGE.
Power Gear Slideout System Manual Override - The slideout system is equipped with a manual override that allows you to extend or retract the room in the event of a loss of power.
Always disconnect battery from system prior to manually operating system. Failure to disconnect battery can cause electricity to back feed through the motor and cause serious damage to the system as well as void the warranty.
Use EXTREME CAUTION when extending/retracting the room using the manual override feature. The gears can be stripped out if the room is manually retracted/extended to its fullest extent and the operator continues to rotate manual override. Damage can also occur to the slide components, slide room structure or trim components. Damages due to misuse of the manual override feature will void any and all claims to the Limited Warranty
If the room does not move when the switch is pressed, check the following: Make sure the slideout system is turned on. Battery is fully charged and connected. Transit bars have been removed (if so equipped).
60
Maintenance Record
Table of Contents
Section 5: Slideout Systems
When the motor brake is disengaged the slideout room WILL NOT lock into place and will not be sealed. When the room has been manually retracted, be sure to install transit bars (if so equipped) and return the motor brake lever to its normal engaged position in order to seal and lock the room into position.
If the room still does not move when the switch is pressed, follow the steps below to manually override the slideout room: 1. Turn the Main Power OFF. The override will not work if it has power going to it. Do
not work on the system unless the battery is disconnected. 2. Locate the slideout controller. There are two versions of the controller. 3. Version 1, unplug the 6 pin wiring harness from the controller. 4. Version 2, remove one of the motor leads, either the motor I or motor II lead from the
controller. 5. Locate the slideout motor (Fig. 1) mounted to one of the slideout rails. Some models
may require removal of the underbelly or cover to access the motor. In a bedroom slideout, it may be located under the bed. 6. Rotate the brake lever, on the backside of the motor, counter-clockwise (looking from the rear of the motor) about 1/8 of a turn to the released position (Fig. 2). This will release the brake that holds the room in place. 7. Locate the manual override for the slideout system (Fig. 1).
8. The room is now free to move. Using either a 5/8" or 3/4" wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room.
9. When the rooms is fully in or out have one person apply pressure to the wrench/ratchet and return the brake lever to its engaged position. This ensures the room is locked into a sealed position.
Maintenance Record
Table of Contents
61
Section 5: Slideout Systems
10. Install the transit bars (if so equipped) to the slideout room and take the unit to an authorized dealer for service.
Refer to the Power Gear® Electric Slideout Operation Manual for detailed operation, safety and troubleshooting information. Power Gear Slim Rack Slideout System The Power Gear® Slim Rack slideout is typically used for slideouts 144" long and longer.
It is operated by a 12VDC electric motor.
The system is equipped with a manual override allowing the room to be extended / retracted in the event of a power loss.
The system has a controller (Fig 1) with programmable stops that stop the motor when the room is fully extended or retracted.
The controller has the ability to detect faults for easier Fig.1 Slideout Controller troubleshooting.
A wall mounted touchpad allows room movement and provides end user feedback.
Operating the Slideout The slideout will not function until the stops are properly set or faults are cleared.
A solid "ON" GREEN LED indicates room movement. The RED LED indicates a fault or a problem with the system. (Refer to the Fault Diagnostics / Troubleshooting).
Prior to moving the slideout room set the parking brake.
To ensure ample voltage is being supplied to the slideout system motor, power should be supplied from one of the following sources:
Attach the RV to shore power. Have the motor home engine running. Turn on the generator.
Extending/retracting the room: 1. Engine or generator must be running, or plugged into shore
power. 2. Transmission must be in park or neutral (if applicable). 3. Set the parking brake and level the unit. 4. Remove transit bars (if so equipped) if extending the
room; install if retracting. 5. Turn ON the on/off switch or key. 6. Press and hold the OUT button (Fig 4). To retract, press
and hold the IN button. There will be a slight delay before the room begins moving. 7. The GREEN LED should be solid ON when room is in motion. 8. Release the OUT button when the room is fully extended or the IN button when fully retracted, and stops moving.
62
Maintenance Record
Table of Contents
Section 5: Slideout Systems
9. Turn OFF the on/off switch or key. Fault Diagnostics / Troubleshooting: The control has the ability to detect and display several faults. When a fault is detected, room movement stops and two different LEDs will flash in a pattern. The RED FAULT CODE LED (Fig 4) will flash a number of times corresponding to a specific fault code (refer to the Fault Code Chart). The GREEN ROOM MOVEMENT LED (Fig 4) will flash GREEN a number of times corresponding to which motor has the associated fault. Example: (4) RED flashes and (2) GREEN flashes indicate a motor fault on motor 2. MAJOR and MINOR faults; faults must be cleared for the room to operate normally.
MINOR faults can be cleared by pushing and releasing the IN or OUT buttons on the wall touchpad (Fig 4).
MAJOR faults must be cleared by pushing and releasing the SET STOPS/CLEAR FAULTS button located on the back of the wall touchpad (Fig 2).
NOTE: For MAJOR faults, the control must be overridden by following the EMERGENCY RETRACT MODE in the Overrides Mode section.
F a u l t F a u l t Fault Codes Code Type Description
1
Major
Stops not programmed
2
Minor System Fault
Possible Cause -Stops have not been set -Stops were cleared -Stops were improperly set
-Obstruction present -Excessive system drag
Possible Solution
Steps need to be programmed by an authorized service facility.
Run room in opposite direction. If it continues to move in the opposite direction, remove obstruction, excessive weight in room or repair of damaged component. If room stops moving in opposite direction, observe fault code and refer to this chart
-Check all connections at
-Bad or loose connec- control box and motor.
Excessive tion
-Check the harness for bro-
4
Major
Battery Voltage
-Defective harness -Open or shorted motor
ken wires.
-Put 12.0 VDC direct to the motor. If it does not run
replace the motor.
Maintenance Record
Table of Contents
63
Section 5: Slideout Systems
6
Minor
Park brake LED flashing
Low voltage LED flashing
Supply voltage to control box is 17 0 V DC or greater
-Parking brake not set (if applicable) -Ground signal lost at park brake control
Incoming violated to control box is below 12.0 VDC
Check 2-pin power connector at control box. If the voltage is 17. VDC or higher, contact O.E.M for power and ground supplies
-Set parking brake (if applicable)
-Check for continuity to ground on wire plugged into park brake connector at control box.
Check 2-pin power connector at control box. If voltage is below 12.0 VDC contact O.E.M for power and ground supplies.
Preventative Maintenance The Power Gear® slideout system requires very little maintenance. Read and follow these procedures:
When the room is extended, visually inspect the slide rail assemblies. Check for excess buildup of dirt or foreign material; remove any debris that may be present.
If the system squeaks or makes any noises, blow out any debris from the gear rack arms and apply a dry lubricant to prevent and/or stop squeaking.
Refer to the Power Gear® website www.powergearus.com for additional information.
Override Modes: In the event of component failure or loss of system power, your slideout can be manually overridden and retracted for travel.
NOTE: During the override procedure, the unit will exit this mode if the room has not been moved for two (2) minutes or if a fault is detected during room movement. The Fault Code (RED) and Room or Lock Movement (GREEN) LEDs will flash rapidly for 10 seconds to indicate the override procedure failed. After 10 seconds of flashing, the control will automatically default to FAULT CODE 1. Programming must be restarted.
NOTE: After overriding the system, the room control will need to be reprogrammed by an OEM authorized dealer.
64
Maintenance Record
Table of Contents
Section 5: Slideout Systems
Emergency Retract Mode Use this procedure when there is NO loss of power or electrical problem with the system. 1. Remove the touchpad (Fig 4) from the wall. 2. Prior to clearing the MAJOR fault, record the number of
RED & GREEN flashes observed on the touchpad (Fig 6). This information will help your dealer/service center in troubleshooting the slideout system. 3. Press and hold the SET STOPS/CLEAR FAULTS button on the back of the touchpad for five (5) seconds (Fig 2). Both RED & GREEN LEDs will be on solid while pressing this button. After 5 seconds, the GREEN LED will begin flashing and the RED LED will remain solid on. 4. The unit is now ready to retract the room. Press and hold the ROOM SLIDEOUT MOTOR buttons 1 and 2 on the back of the touchpad (Fig 3).
It is very important to note that during this procedure, the slideout control has NO stop locations. Use a second person to assist in determining when the room is retracted. Damage to the room can occur if the room is retracted too far.
Press the IN button on the front of the wall touchpad until the room is fully retracted. If one side of the room needs to retract further in order to get a good seal, press and hold the motor button (Fig 3) corresponding to ONLY the motor you want to move. Press the IN button on the front of the touchpad to retract the room the remainder of the way.
5. Re-install the wall touchpad. 6. Take the unit to an OEM certified dealer for repairs. Manually Retract Room with Ratchet and Socket If the power is lost to the slideout motor(s) or the override mode above will not work, the room may be manually retracted using a ratchet and socket attached to the end of the coupler (Fig 11).
1. Gain access to the VERTICAL CHANNEL assembly from inside or outside of the coach (whichever is more convenient). Remove the trim and flange pieces on the slideout room box.
2. If applicable, remove the top screw from the bulb seal at the top of the VERTICAL CHANNEL (Fig 8).
3. Pull down the bulb seal and remove the motor cover (Fig 9). The motor seal may stick to the bulb seal.
4. Using a pick tool, remove the end of the retaining spring from the motor spring clip (Fig 10A). If not equipped with a retaining spring, loosen the motor retaining screw (Fig 10B).
5. Unplug the motor from the harness and remove the motor by lifting it up and out. 6. Repeat steps 1-4 for the other side. 7. Place a socket wrench with a 3-inch extension and a 5/8" deep well socket (Fig 12)
through the motor access opening and seat the socket onto the coupler (Fig 13). One person alternating from side to side of the room can retract a 1500 lb. room with or without a ramp.
Maintenance Record
Table of Contents
65
Section 5: Slideout Systems
NOTE: One person on each side of the room with a ratchet and socket will expedite the process. Room moves ¼ inch for every 30 to 40 degree turn of the wrench.
8. Secure the room in place by either: Re-installing the motors (making sure the end of the retaining screw is re-hooked to the motor spring clip (Fig 10A). Torque the motor retaining screw to 40 inch/lbs. (Fig 10B) and the motor retainer is fully engaged. Use a travel lock, (a 2x4 cut to size), etc. Refer to Fig 10A and 10B for proper seating of the motor.
9. Have the slideout room serviced by an OEM authorized dealer as soon as possible. Do not operate the room until service is complete as damage to the room may result.
Power Gear Ram Slideout System Typically used for Class C motor homes.
Manual Override Procedure The system has been equipped with 3/4" hex override couplers located on the drive component of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
66
Maintenance Record
Table of Contents
Section 5: Slideout Systems
Use the following steps to mechanically operate the room:
1. Locate the ABS motor access cover for the slideout. This cover will be located inside one of the storage compartments under the slide room up at the top of the compartment.
2. Remove 4 screws holding the panel to the top of the compartment. Remove the cover.
3. Unplug the motor leads at the connector. Gray connector with red and black wires.
4. To release the motor brake you must depress the spring lock lever, which then allows you to pivot the brake lever, which in turn releases the brake. These parts are located inside the rubber boot wire tied over the motor. You must manipulate these parts without removing the rubber boot. As noted on the side-by-side photo, removing this boot will void your motor warranty. These photos will help you figure out how this works. The side-by-side photo (below) shows the spring lock lever and the brake lever.
5. The spring lock lever is a thin metal arm with a slight bend at the end, which will hold the brake lever in the released position.
6. The brake lever is the heavier thicker metal arm with the hole in the end.
7. The normal position for these two levers is to be parallel to each other as shown in the first side-by-side photo. The motor brake is engaged with levers side by side.
8. The brake lever is moveable; the spring lock lever is not moveable. To release the brake lever, you must push the bent end of the spring lock lever away from the brake lever; this will allow you to pivot the brake lever so it moves over on top of the spring lock lever. The bent end will hold the brake lever in the released position. (photo shows this "bend").
9. Once the brake motor is released, you will need to remove the skirting on the side of the slideout floor where the hex override is located.
10. Use a ratchet with a 3/4" socket (or wrench) to turn the hex override and manually move the slideout.
11. When the slideout is retracted, check to make sure you have a good seal, and replace the skirting on the slideout.
12. Return the brake release lever back to the "engaged" position (parallel to the spring lock lever). Pressing the bent end of the spring lock lever will allow the brake lever to be moved.
13. Plug the motor connector back in again. 14. Replace the plastic motor cover with the 4 screws removed previously. 15. Take the unit to an authorized dealer for service.
Maintenance Record
Table of Contents
67
Section 5: Slideout Systems
For further information, refer to the manufacturer's owner's manual.
68
Maintenance Record
Table of Contents
Section 6: Electrical System
The Electrical System
The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it. Changes or additions made after delivery may result in a hazardous condition. Service and/or modification of the electrical system should only be performed by qualified electrical technicians using approved materials, components, and methods meeting current safety and code requirements. Consult your dealer's service department for assistance. To read more about the various components incorporated into the RV electrical system, please refer to the information contained in your Warranty Packet. For motorized vehicles, consult the Chassis Guide for information pertaining to the chassis drivetrain electrical system. Electrical System Maintenance Before working on the electrical system:
Make sure the inverter/charger (if so equipped) is turned "off" before disconnecting batteries.Disconnect the shore power cord.
If equipped with a generator, turn off the generator and disable the automatic generator start functionality.
Turn off the battery disconnect switch (if so equipped) Turn off the 120V main circuit breaker. Disconnect the negative 12VDC battery terminal from the battery.
Use caution when using metal tools. If a tool contacts a battery terminal or metal connected to it, a short circuit could occur which could cause personal injury, explosion or fire.
In Case Of An Electrical Fire
Do not attempt to use water to put out an electrical fire. Water can spread some types of fire, and electrocution is possible with an electrical fire.
EVERYONE SHOULD EVACUATE THE RV IMMEDIATELY: Switch the 120-volt main circuit breaker to the "off" position. It is important that everyone knows where to find the main circuit breaker and how it operates. Disconnect twhe negative battery cable(s) at the battery. Disconnect the power cord from the shore power receptacle. Turn "off" the generator (if so equipped).
Always have faulty or damaged wiring and electrical components repaired immediately.
Maintenance Record
Table of Contents
69
Section 6: Electrical System
Controls and Switches
Your motor home is equipped with various switches and controls that allow you to operate and monitor the systems in your motor home.
Information on these controls and their location will be provided throughout this manual. Additional information on the various components can be found in the component manufacturer's user guide.
Command Center
The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, configurations and components will vary by model.
Command Center Panel or Command Center Panel with Switch Modules
Items found on these panels may include:
Fuel gauge and hour meter with switches for fuel pump and
fuel levels; fuel station (if so equipped) on/off switch
Lighted red pump and water heater switches (electric & LP
gas) Generator start / stop switch; may include hour meter
Command Center Panel
Tank heater switchesLight switches for porch lights, exterior
security lights, interior lights, awning LED lights, front cap
LED accent lights, power entry step
Cargo bed red lighted control switch
Slideout control switches (press and hold to extend / retract)
Awning control switches (press and hold to extend / retract)
Systems monitor with LED indicators for tank levels and bat-
tery charge status
Auto leveling control panel (for leveling the RV)
Inverter panel (power switch with display)
Power bunk bed lift control switch
Speaker selector switch
Command Center Modules Mounted to the Wall
Some models may have the modules mounted directly to the interi-
or wall of the vehicle. They are typically located near the entrance
door.Touch Dimmer Switch:
Touch Dimmer Switch: Certain models may include a touch dimmer switch next to the Command Center Panel Command Center panel. (There are no interior light switches on the w/Switch Modules Command Center panel).
· Turn ON ceiling lights: Tap the LED light on the dimmer
· Turn OFF ceiling lights: Tap the LED light on the dimmer
· Dimmer: If lights are off, hold finger on the LED light and lights will begin turning on gradually until fully lit. If lights are on, hold finger on the LED light and lights begin to gradually turn off.
The dimmer has a memory so it remembers what the light setting was when the lights were turned OFF. When turned ON again, the lights return to that same setting.
70
Maintenance Record
Table of Contents
Section 6: Electrical System
NOTE: If your RV model includes the 5 way/8 way remote control: the LIGHT button on the remote only controls the awning LED lights
GFCI Circuit Breakers
Ground fault current interrupter breakers are engineered into the electrical system. They are designed to reduce the possible injury caused by electric shock. The breakers will not protect against short circuits or circuit overloads. Typically there is a GFCI circuit breaker panel (known as a G6A or G12A panel) located in a bathroom cabinet or in a basement compartment. The panel offers the benefits and convenience of breaker-style manual and auto-reset circuit protection. In addition to circuit protection, the panel supports control of different systems including lighting, pumps and motors, leveling jacks, slideouts, awnings, generators and more.
Testing The Campsite Power Connection
The campsite 120-volt power receptacle(s) should always be tested for proper functionality prior to plugging the recreation vehicle shore power cord into it. Campsite 120-volt power receptacles can be tested using a digital multimeter or a dedicated circuit analyzer. Dedicated circuit analyzers plug directly into the campsite power receptacle and minimally test for open neutral, open ground, and correct polarity. Connecting the Power Cord Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it. If the ground monitor indicates `reverse polarity' or an `open ground' DO NOT connect the power cord. To help prevent power surges from damaging the connected loads, please follow these instructions when hooking up to the external power source: 1. Turn off the load center main 120-volt circuit breaker. 2. Carefully extend the entire length of the power cord (approximately 25'-35') from the
electric cable hatch to the external power source. 3. Plug the power cord into the receptacle. Be sure all the power cord prongs are properly
plugged into the receptacle. 4. Return to your RV and turn on the load center main circuit breaker. The shore power cord should be unplugged when the recreation vehicle is left unattended When you are ready to leave, reverse the power cord connection process. Use care to prevent damaging the power cord electrical connection pins when connecting or disconnecting the shore power cord. Grasp the plug to remove the power cord from the outlet; do not unplug it by pulling on the cord.
Maintenance Record
Table of Contents
71
Section 6: Electrical System
Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. DO NOT plug the shore power cord into a campsite receptacle(s):
That has reverse polarity With non-functioning ground circuits That shows outward signs of heat damage. Doing so may result in property damage or serious injury. Plugging the shore power cord into an incorrectly wired power source could damage the recreation vehicle electrical system and result in severe or fatal injury. Damage or injury resulting from connection to malfunctioning or improperly wired power sources is not covered by your recreation vehicle warranty.
DO NOT
Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.
Do not connect the power cord into an outlet that is not grounded, or adapt the power cord plug to connect it to a receptacle for which it is not designed.
Do not remove the grounding pin to connect to a non-grounded receptacle. Removal of the ground pin disables an important safety feature designed to prevent shock and electrocution hazards.
Do not connect the power cord to an extension cord. Use of an improper extension cord will cause overheating of the cord as well as potentially causing premature failure of the AC equipment.
The power cord must be fully extended when in use and not left coiled in the electrical compartment or on the ground. A power cord left coiled may potentially create enough heat to melt its protective casing.
It is the responsibility of the owner of the electrical receptacle to ensure that the receptacle is properly wired and grounded. Reverse polarity and/or improper grounding of your RV can cause property damage or serious personal injury.
Maintenance Inspect the power cord for cuts, cracks and worn insulation. Have the power cord replaced immediately if these symptoms are noticed.
Inverter (if so equipped)
A factory installed inverter converts 12-volts DC to useable 120-volts AC and supplies continuous AC power to the appliance plugged into it. It is important that you familiarize yourself with the inverter function and operation. The inverter should be "off" when not in use.
The factory installed inverter is not intended for use, nor should be used, with any medical device(s). The inverter may, however, be used with some CPAP machines, depending on the CPAP model. Consult your CPAP machine's instruction manual before use to ensure proper operation.
If your recreation vehicle is equipped with a residential style refrigerator, the inverter may be used to supply the 120-volts AC necessary to power the refrigerator.
72
Maintenance Record
Table of Contents
Section 6: Electrical System
Maintenance There are no customer serviceable parts inside the inverter case and the manufacturer's warranty will be void if the case has been removed. The inverter cooling fins and the cooling fan should be kept clear of any obstructions. Your RV may have an inverter remote display (appearance may vary) on the Command Center switch panel. There are power and select buttons, Status/Display indicators and a single line digital alpha- numeric display. The display can show measured battery voltage, AC output power, inverter settings and error codes.
NOTE: When in Inverter Mode you will be able to cycle through Battery Voltage, Inverter Power, inverter settings and error codes. When in Bypass Mode you will be able to cycle through Battery Voltage, inverter settings and error codes. Inverter Power will not be available because the inverter is idle.
POWER button is used to turn the inverter on and off. To turn on the inverter and the LED display press and hold POWER for 1 second until you hear a beep. The STATUS and DISPLAY indicators indicate the inverter status:
· STATUS & DISPLAY LEDS - both GREEN - Unit is plugged into shore power. The panel is in Bypass Mode and will display battery voltage in DC volts.
· STATUS LED AMBER, DISPLAY LED GREEN - Inverter Mode is active. Inverter is ON and will display battery voltage in DC volts. (Not connected to shore power)
· STATUS & DISPLAY LEDS - both AMBER - Inverter Mode is active. Inverter is ON, pressing the SELECT button will display inverter power output. Display shows power output in KW.
· STATUS LED FLASHES AMBER, DISPLAY LED IS OFF - If the unit is in Inverter Mode, and you plug in shore power, the STATUS LED will begin flashing AMBER and the unit will switch to Bypass Mode within 20 seconds of detecting an AC input.
· If the STATUS LED is RED and DISPLAY LED is OFF, the display will show an error code of E01 through E12. This indicates a fault in the inverter circuit that needs attention. Inverter will shut down.
NOTE: The power button is NOT a power disconnect switch and will not remove DC power from the inverter. Disconnect ALL power from the inverter before working on it.
Maintenance Record
Table of Contents
73
Section 6: Electrical System
Pressing the SELECT button also cycles through inverter settings. Inverter settings can be changed, but 12VDC must be removed from the Ignition Start Port on the back of the inverter. Unplug the 12VDC wire(s) on the back of the inverter to make changes to inverter settings. Plug +12VDC back in after settings are changed. (See photo)
Refer to the Inverter manufacturers' manual in your warranty packet for further operating instructions, error codes, changing inverter settings and safety information.
Ignition Start Port
Power Converter
The power converter converts 120-volt AC power to useable 12-volt DC power when the shore power cord is connected to an external power source.
The converter has a built-in protective thermal breaker that will shut it down should overheating occur. Overheating can be caused by operating the converter above its maximum power output for an extended period of time, or by an obstruction to its ventilation air flow. To reduce converter heat build keep unnecessary 12-volt lights and motors turned off. Keep the converters cooling fins and fan clear of obstructions.
USE ONLY A DEEP CYCLE BATTERY FOR RV USE. Car batteries (CCA rating) are not designed for RV applications.
If using multiple batteries they must be the same brand and type. Adding more batteries will provide longer use of DC appliances when not on shore power but may reduce charging efficiency.
The battery works in conjunction with the converter to supply DC power to the RV. A battery is typically only necessary if you do a lot of dry camping or have slideouts and/or a leveling system.
Reverse polarity fuse provides protection for the converter when a battery is used. If the battery is connected backwards to the fuse board this fuse would blow preventing damage to the converter.
Dimming or flickering lights usually indicates an overloaded converter. Remove some of the load by turning off DC lights or appliances.
Fan is controlled by load. It will begin running at 3 to 6 amp DC draw. It increases in speed with a higher load until 14 to 15 amps. Fan is at maximum speed and stays there even with more load. If load drops below 6 amps DC, the fan shuts off.
It is important that the fluid level of any connected batteries be checked on a regular basis. All batteries will "gas" and lose some fluid when continuously connected to any charging source (does not apply to "gel-cell" batteries).
Before checking for converter output voltage, the battery cables must be disconnected at the battery. Make sure the converter is plugged into an AC source (105-132 AC volts). Check the converter output voltage at the battery with a voltmeter. Place the voltmeter probes on the disconnected battery cables. If the voltage reads 13.6VDC with no load, the converter is functioning properly.
If the converter output voltage at the battery reads in the 0.0VDC range, or the battery is not charging, check for:
74
Maintenance Record
Table of Contents
Section 6: Electrical System
An open inline fuse in the battery wire An open wire between the converter and the RV battery Loose ground connection Improper torques If the converter fuses and AC voltage are good, but the converter output still reads zero volts, the converter is not functioning properly.
Modes of Operation Absorption (Normal) Mode: 13.6VDC range. Batteries are being charged, just at a slower rate. Converter will not work without AC input.
Float Trickle Mode: To get your converter into this mode, reduce the load on the system to almost nothing but the battery. Let the system sit for approximately 44 hours.
Converter voltage will drop to 13.2VDC. If the converter sees any load during this period or after it is in Float Mode it will revert back to Absorption (Normal) Mode. 13.6VDC.
Bulk Mode: Converter will not jump into the Bulk Mode unless the battery is below 50% of charge, or approximately below 13.2VDC output voltage. There is no way to force it to go into Bulk Mode.
Red LED indicates blown fuse.
Inspection and maintenance If the 12-volt power converter is not working (auxiliary battery not being charged) check the reverse polarity fuse(s) located on the end of the converter.
There are no customer serviceable parts inside the converter case and the manufacturer's warranty will be void if the case has been removed. If you have further concerns contact your dealer.
For detailed information on operation and safety, refer to the manufacturer's owner's manual. Converter w/Charge Wizard (if so equipped) Some converters may be equipped with a charge wizard There are (3) possible charging modes; NORMAL, BOOST and STORAGE. The charge wizard will automatically select the best mode to charge your battery. A green LED next to the wizard mode button will indicate by flashes, which mode is currently being used.
Normal Mode: Green LED flashes once per second; battery is between 50% and 90% charged. Green LED flashes 2-3 times per second; battery is 90% charged. Output voltage is 13.6VDC and the converter is safely completing the charge of the battery.
Boost Mode: Green LED is on solid. Output voltage is 14.4VDC to rapidly charge the battery up to 90% of full charge.
Storage Mode: Green LED flashes every 6-8 seconds. Output voltage has been reduced to 13.2VDC; the RV battery is fully charged and converter is maintaining the charge.
Manual Mode (not recommended): The manual mode button is used to override the charge wizard. Refer to the converter owner's manual for additional information.
Reverse Battery Protection: Reverse polarity fuse(s) provide protection for the converter when a battery is used. If the battery is connected backwards to the fuse board a fuse will blow preventing damage to the converter. Four easily accessible fuses are located next to the wizard button. Replace with fuses of the same type and rating.
Maintenance Record
Table of Contents
75
Section 6: Electrical System
12-volt DC System
The majority of your motor home lighting is powered by 12-volt electricity. The 12-volt DC system is composed of components that will operate when the following conditions are met:
Power is supplied by the chassis alternator when the chassis engine is running. 12-volt DC power is supplied when the shore power cord is plugged into a 120-
volt external power source. House batteries will be charged also in most situations. The house batteries power many interior 12-volt components including the lighting fixtures, water pump, 12-volt motors, 12-volt appliances, etc., when the motor home is not connected to a 120-volt power source. 12-Volt Fuse Panel
Replacement fuses must be of the same voltage, amperage rating and type. Never use a higher rated replacement fuse; doing so may cause a fire by overheating the RV wiring.
The 12-volt fuse panel is labeled to indicate fuse sizes, positions and the components powered. Fuses are located in the load center. Replacing a Fuse Before replacing a fuse, always turn off the electrical components protected by it. 1. Disconnect the shore power cord. 2. Inverter should be OFF. 3. Remove the fuse panel cover to check fuses. 4. Pull the fuse straight out of the fuse block. 5. Insert a new fuse of the same specified voltage, amperage rating and type in the original
location. The fuse panel label should be kept permanently affixed to your recreation vehicle. Fuses will not offer complete protection of the electrical system in the event of a power surge or spike. 12-Volt DC Outlet There may be one or more 12-volt DC power outlets in your recreation vehicle. When the 12-volt DC outlet is used as a power source for an electric appliance, make sure the appliance operates on 12-volt DC power and that it consumes less than 60 watts (5 amps) of power.
Keep the protective dust cap on the 12-volt DC outlet when not in use to prevent ingestion of foreign material and potential short circuit conditions.
76
Maintenance Record
Table of Contents
Batteries
Section 6: Electrical System
Do not store anything inside the battery compartment(s) or near the batteries that could touch the battery or battery cable terminals. Contact with the battery or battery cable terminals could cause an electrical short circuit, discharge the batteries, or start an electrical fire.
Keep sparks, cigarettes and flames away from the batteries as the hydrogen gas they create may explode. Do not connect a booster battery or other power source that outputs more than 14.2-volts DC to the motor home batteries. Use adequate ventilation when charging or using batteries in an enclosed space.
Remove metal jewelry and always wear eye protection when working around batteries.
Do not allow battery electrolyte (acid) to come into contact with skin, eyes, fabric or painted surfaces. Electrolyte is a sulfuric acid solution that could cause serious personal injury or property damage. If your hands, eyes, clothes or the painted surface of your motor home are exposed to electrolyte, flush the exposed area thoroughly with water. If electrolyte gets in your eyes, immediately flush them thoroughly with water and get prompt medical attention.
Make sure the inverter/charger is turned "off" before disconnecting the negative battery cable from the battery bank. Keep the batteries out of the reach of children.
House Batteries Your motor home is equipped with Group 24 deep cycle batteries.
Unless a battery has been fully discharged, house auxiliary batteries are normally charged in one of two ways:
The chassis alternator charging system supplies power to the house auxiliary batteries when the engine is running and the chassis batteries are sufficiently charged.
When the power cord is plugged into 120-volt shore power, or when the generator (if equipped) is operational, the inverter/charger functions as a battery charger and will automatically charge the house batteries when required.
A fully charged battery will read 12.65 volts DC with a specific gravity of 1.265 at 80°F (32°C). A battery is considered discharged at 11.89 DC volts or when it has a specific gravity of 1.120 or less. When voltage drops to 11.89 volts, irreversible battery damage can occur.
Dry Camping House auxiliary and chassis batteries should be fully charged prior to dry camping. When disconnected from 120-volt shore or generator power (i.e., while dry camping or tailgating) all electrically operated appliances and accessories must be used sparingly. Typically, a deep cycle battery has an amp-hour rating of 75-100 amps.
During this period these appliances and accessories are being powered by the house auxiliary batteries directly, and/or indirectly through the inverter/charger. If excessive amounts of power are drawn from the house auxiliary batteries, they will become deeply discharged. Permanent battery damage will occur after repeated deep discharge cycles.
Battery Inspection and Care Check the level of electrolyte in each battery cell once a year.
Maintenance Record
Table of Contents
77
Section 6: Electrical System
Add distilled water as needed to reach the split-level marker on each battery. Keep batteries and battery terminals clean and tight.
Check the external condition of the batteries periodically. Look for cracks in the cover and case. Make sure battery vent caps are tight and replace them if they are cracked or broken. Battery storage instructions To prevent house auxiliary battery discharge when your motor home will not be connected to shore power for extended periods of time, it is recommended you turn "off" the 12-volt battery disconnect switch, or "main power switch," and disconnect each battery bank at the negative battery cable running to the chassis frame.
During storage, it is important to check battery voltage at least every two weeks and to recharge them as needed. If you remove the batteries from your motor home protect them from accidental shorting and keep them in a cool, dry, well ventilated area. Battery Replacement If house auxiliary batteries need to be replaced, only deep cycle batteries of the same size and type should be installed. Do not reverse the positive and negative battery cables. Doing so will blow the reverse polarity fuses that protect the power converter. For more information Contact the battery manufacturer for more information on the house auxiliary batteries. Refer to your Chassis Guide for information pertaining to the chassis batteries. 12-Volt Battery Disconnect The 12-volt battery disconnect switch is typically located near the entrance door. This momentary switch controls a solenoid which connects or disconnects the house batteries. The switch lights up red when turned on.
When engaged the battery disconnect solenoid supplies battery power to all accessories connected to the house 12-volt fuse panel. The solenoid must be engaged for the 12-volt house electrical system to operate.
The battery disconnect feature should be used to disconnect the motor home from house battery power during periods of storage or during maintenance.
NOTE: The combination carbon monoxide/propane alarm requires a constant 12-volt power source. The carbon monoxide/propane alarm remains operational when the battery disconnect solenoid switch, or "main power switch," is in the "ON" position or when the ignition key is rotated to the "ON" position.
If the Main Power switch is turned OFF, the power entrance door steps will still function when the door is opened.
Depending on your model, your motor home will be equipped with either a Battery Isolator Solenoid or a Battery Isolation Manager. Battery Isolator Solenoid (if so equipped) The isolator solenoid breaks the connection between the house batteries and the chassis battery when the ignition key is in the "OFF" position.
78
Maintenance Record
Table of Contents
Section 6: Electrical System
Breaking this connection prevents discharge of the chassis battery (used to start the engine) when using 12-volt devices in the house section of your motor home.
When the engine is running the isolator solenoid engages allowing the house batteries to be charged by the vehicle alternator. Battery Isolation Manager (if so equipped) Your motor home may be equipped with a Battery Isolation Manager that monitors the battery voltage of both the chassis and house batteries over long periods of time. If it senses a charging voltage it connects the two batteries together. If the charge system is overburdened, it isolates both batteries. When batteries have reached a float charge state for (1) hour, the batteries are isolated to prevent overcharging.
It will reconnect if either battery drops to approximately 80% charge and the other is being charged. If batteries are not being charged they will be isolated to prevent an electrical draw in one system from depleting the other battery. Auxiliary Start System (if so equipped) Depending on your model, the Battery Boost switch (on the driver console) or the Auxiliary Start button (under the steering wheel on the lower dash) engages this solenoid and joins the house battery with the chassis battery to provide a "boost" to help start the motor home if the chassis battery charge is low.
The auxiliary start switch can momentarily connect both the house and chassis batteries should the chassis battery become discharged.
To operate, depress either the "Aux. Start" switch (located on the front driver's dash) or the Battery Boost switch on the driver console and hold it down. While the "Aux. Start" switch or Battery Boost switch is depressed use the ignition key to start the chassis engine. Release the "Aux. Start" switch (or Battery Boost switch) after the engine has started.
Load Center
The Load Center contains 12VDC fuses and 120VAC circuit breakers for almost all of the electrical appliances and circuits in the RV. The 120V main breaker may be located in this panel and will turn off all 120-volt power to the RV. Locations will vary by model. Refer to the diagram inside the load center for specific fuse assignments.
Motor homes may have separate small panels for breakers and fuses. They are normally located in close proximity to each other typically in the bed platform. The converter is also mounted separately (typically under the bed platform).
Maintenance Record
Table of Contents
79
Section 6: Electrical System
Automatic Transfer Switch (ATS)
Your motor home is equipped with an Automatic Transfer Switch with built in reverse polarity protection. The ATS is microprocessor controlled and will automatically detect which power source is being used (generator or shore power) and allow power from that connection only. You will not have to plug and unplug power to the coach if you decide to run the generator. If you plug into shore power, the ATS will pass power to the motor home. If the generator is started, it will override the shore power input (called generator dominant) and supply the RV with electrical power from the generator. When the generator is shut down, shore power is restored. There may be a slight flicker of the lights when the ATS changes over from one to the other, but there is no real interruption of power. The ATS will disconnect from shore power completely if the power coming in is not high enough quality (i.e. either low/high voltage, or low/high frequency). When the generator is operating, it powers the inverter/charger which in turn functions as a multi-stage battery charger to charge the house auxiliary and chassis batteries. Refer to and follow safety information found in the manufacturer's troubleshooting guide found in your warranty packet.
NOTE: The (diesel or gas powered) generator requires 12-volt power from the house auxiliary batteries to start, and draws (diesel or gas) fuel to operate from the chassis fuel tank. If the fuel level in the chassis fuel tank drops to or below ¼ full, the generator will automatically shut "off" and cannot be re-started until the fuel tank is filled to above ¼ full.
120-Volt Circuit Breakers
The 120-volt AC circuit breakers located inside the load center protect all 120-volt wiring and components from circuit overloads and short circuits. Should a circuit overload or short circuit occur the circuit breaker protecting the affected circuit will "trip" preventing the flow of electricity through that circuit. If a circuit breaker trips, shut off the appliance on that circuit (i.e., power converter, etc.) and allow the circuit breaker to cool down for a brief period of time. After it cools down, reset the circuit breaker by moving its lever "off" and then back to the "on" position. If the circuit breaker re-trips or frequently trips, contact your dealer to have the electrical problem diagnosed and repaired. A circuit breaker identification label is permanently attached to the inside surface of the 120volt Load Center.
Circuit breakers and fuses will not offer complete protection of the electrical system in the event of power surge or voltage spike.
Replacement Only replace circuit breakers with those of the same specified type, voltage, and current rating. Never replace a circuit breaker with one listed at a higher amperage rating. Please contact your dealer for repair assistance when replacing circuit breakers.
80
Maintenance Record
Table of Contents
Section 6: Electrical System
Replacement circuit breakers must be of the same voltage, amperage rating and type. Never use a higher rated replacement circuit breaker; doing so may cause a fire by overheating the RV wiring.
Maintenance At the beginning of the camping season, inspect the circuit breakers and replace as needed. Test by turning each circuit breaker "off" and back "on". Circuit breakers are wearable parts and must be replaced as needed as part of your RV maintenance. If you have any questions, contact your dealer. A label is provided to explain the function of every 120-volt circuit breaker. This label is located on or near the appropriate load center or sub-panel and must remain permanently affixed to the recreation vehicle.
Maintenance Record
Table of Contents
81
Section 6: Electrical System
Approximate Electrical Load Ratings
12 VOLT SYSTEM
Exterior Entertainment Center
5-7 AMPS
Fan
1.5 AMPS
Furnace
12.0 AMPS
Generator Start
95.0 AMPS*
Illuminated Switch
.125 AMP
Inverter
variable
Leveling System
95.0 AMPS*
LP Detector
.125 AMP
Light; LED
1.7 AMPS
Light; Vanity
4.2 AMPS
Lights; Aisle
1.0 AMP
Lights; Baggage Compartment / Shower
1.4 AMPS
Lights; Decorative Wall / Map / Porch
1.5 AMPS
Lights; Double -12"
2.0 AMPS
Lights; Double -18"
2.5 AMPS
Power Awning
10.0 AMPS*
Power Vent
5.0 AMPS
Refrigerator
3.0 AMPS
Step Cover
10.0 AMPS*
TV Plate/Antenna Booster
1.0 AMP
Water Heater
6.0 AMPS
Water Pump *Momentary Load
7.0 AMPS
12 Volts: Labeled watts divided by 12 = Power consumed in AMPS
120 VOLT SYSTEM
Air Conditioner
18 AMPS
Coffee Maker
6-12 AMPS
Converter (each)
8 AMPS
DVD System
3 AMPS
Fireplace
15 AMPS
Hair Dryer or Curling Iron
10-14 AMPS
Microwave
15 AMPS
Refrigerator
6 AMPS
Satellite Receiver
2 AMPS
TV
2-4 AMPS
Vacuum Cleaner
8 AMPS
Washer/Dryer
12 AMPS
Water Heater
12 AMPS
120 Volts: Labeled watts divided by 120 = Power consumed in AMPS
82
Maintenance Record
Table of Contents
Section 6: Electrical System
120-Volt 50 AMP AC Electric System (if so equipped)
The 50 amp 120-volt 60hz AC electrical system can be powered by an outside 120/240-volt 60hz utility service like those commonly found in campgrounds or by 120/240-volt 60hz generator power. The entire system is designed to operate on 2 legs of 120-volt power at a maximum current flow of 50 amperes per leg. Exposure to voltages higher or lower than a nominal 120-volts, will damage or shorten the service life of the electrical system and appliances. The 50 amp 120-volt 60hz AC electrical system can be powered by an outside 120/240-volt 60hz utility service like those commonly found in campgrounds or by 120/240-volt 60hz generator power.
The following electrical components will only operate when connected to 120-volt power: air conditioner(s), refrigerator, microwave oven, television(s), home theater system(s), water heater, washer, dryer, fireplace, electric stove, and appliances plugged into convenience receptacles. These components will create a surge on the inverter.
Circuit breakers and fuses will not offer complete protection of the electrical system in the event of power surge or voltage spike.
Make certain the external power source you connect the power cord to is a properly wired 50 amp NEMA 14-50 RV receptacle and not 240 volt AC.
PLUG INTO 50-AMP SERVICE ONLY.
50 amp Power Cord
Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores.
Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.
Do not connect the power cord into an outlet that is not grounded, or adapt the power cord plug to connect it to a receptacle for which it is not designed.
Do not remove the grounding pin to connect to a non-grounded receptacle. Removal of the ground pin disables an important safety feature designed to prevent shock and electrocution hazards.
Do not connect the power cord to an extension cord. Use of an improper extension cord will cause overheating of the cord as well as potentially causing premature failure of the AC equipment.
It is the responsibility of the owner of the electrical receptacle to ensure that the receptacle is properly wired and grounded. Reverse polarity and/or improper grounding of your recreation vehicle can cause personal injury or death.
The 50-amp external utility power cord is commonly referred to as the "shore" power cord. It is designed to mate and properly function with 50-amp "shore" power receptacles available at most campgrounds.
Maintenance Record
Table of Contents
83
Section 6: Electrical System
The shore power cord is designed to continuously carry the 50-amp current flow required to power each leg of the electrical system. It also creates a critical ground connection between the vehicle electrical system and the campground shore power receptacle.
Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it. If the ground monitor indicates `reverse polarity' or an `open ground'. DO NOT connect the power cord. Regularly inspect the shore power cord for cuts, cracks, worn insulation and other damage. Have the power cord replaced immediately if problems exist. Calculating 50 amp Electrical Load (if so equipped) When connecting appliances to the electrical system, 120-volt power usage is limited to 50 amps per electrical system leg for a total of 100 amps. Operating appliances collectively places an added load on your 120-volt electrical system.
A circuit breaker "trip" may occur if you overload the recreation vehicle and/or campground electrical system. The amperage rating of individual appliances can be calculated by dividing appliance wattage consumed (normally listed on the appliance) by nominal design voltage (120 for a 120-volt appliance). For example: 1200 watts divided by 120-volts equals 10 amps.
Generator
Your motor home may be equipped with an LP or diesel powered generator. In certain gasoline engine motor homes, the generator will be gasoline powered as well. The generator produces 120/240-volt power compatible with the motor home electrical system. It can power the entire motor home when 120/240-volt shore power is not available.
CARBON MONOXIDE IS DEADLY! Do not run the generator when your motor home is indoors or in a confined space. DO NOT use the AGS AUTO ON or QUIET ON modes (if so equipped) when your motor home is indoors or in a confined space.
Asphyxiation or carbon monoxide poisoning hazards exist whenever generator exhaust gasses can accumulate.
MOVING PARTS AND ELECTRICITY can cause severe personal injury or death. To reduce exposure to these hazards, always disable AGS (if so equipped) before:
Sleeping in vehicle, unless vehicle has a working CARBON MONOXIDE detector.
Parking vehicle in garage or confined space. Parking vehicle for storage. Servicing vehicle for storage. Servicing generator. Servicing batteries. Servicing appliances or electrical systems. Fueling the vehicle.
Before Starting the Generator 1. Make sure the carbon monoxide detector is working. 2. Turn off air conditioners and all other 120-volt appliances. 3. Check for fuel, exhaust and coolant leaks.
84
Maintenance Record
Table of Contents
Section 6: Electrical System
STOP the generator immediately if there is a fuel, exhaust or coolant leak. Have all leaks repaired prior to placing the generator back in service. Automatic Generator Start (AGS) (if so equipped) If your motor home is equipped with a Vegatouch system, it may include an AGS screen to program your generator to automatically start and stop at specified times. The AGS button is located on the home screen of the Vegatouch display. Please refer to your Vegatouch User Guide in your warranty packet or online at http://www.fireflyint.com. Transfer switch For more information, see the Automatic Transfer Switch (ATS) section..
NOTE: The diesel (or gas) generator requires 12-volt power from the house auxiliary batteries to start, and draws diesel fuel (or gas) to operate from the chassis fuel tank. If the fuel level in the chassis fuel tank drops to or below 1/4 full, the generator will automatically shut off and cannot be re-started until the fuel tank is filled to above 1/4 full.
Excessive usage can overheat and damage the generator starter motor. Do not engage the starter motor for more than 20 seconds at a time. If the generator does not start after the first attempt, wait at least two minutes before beginning another start sequence. If the generator does not start after a third attempt, refer to the generator owner's manual for additional information.
Maintenance During periods of extended storage: 1. Add a diesel fuel additive to the chassis fuel tank to prevent algae growth (only with a
diesel fueled generator). 2. Completely fill the chassis diesel fuel tank to prevent water condensation and rust in the
tank (only with a diesel fueled generator). 3. Cover the end of the generator exhaust pipe with screen to prevent bug and rodent
intrusion. With the exception of simple items, such as normal maintenance (i.e., oil changes, etc.), all service work should be done by an authorized repair facility. Improper adjustments can damage the generator and electrical appliances and can result in a safety hazard. Follow the generator owner's manual for maintenance intervals and recommendations. Exercising Your Generator When storing the generator for extended periods of time, it is important to run the generator regularly to keep it in good working order. Lack of exercise can cause moisture build-up in the fuel system resulting in poor performance. For more information on generator operation and maintenance, refer to the generator owner's manual.
Maintenance Record
Table of Contents
85
Section 6: Electrical System
Starting the Generator
AGS (Automatic Generator Start) Your motor home may have The Magnum® Standalone AGS system. This system monitors
your battery system or surrounding temperature, and starts the generator when the battery re-
quires charging or power is needed to run the air conditioner. The AGS system uses a remote
switch setup and does not use the standalone switch provided with the Magnum® system.
The AGS startup switches are typically located on the command center panel.
Manual Generator function To start the generator manually, make sure the parking brake is engaged. The ENABLE button (on the panel) is not used for manually starting the generator. Press the START button until the generator fires, and the indicator light above the switch comes on.
To stop the generator, press the STOP button. AGS Controller The AGS controller is typically located in a bathroom cabinet, and is used to set the run time hours, start temperature, start voltage, clock and the quiet time. For information on setting these controls, refer to the Magnum® AGS owner's manual.
Automatic Generator Function Before using the AGS system set the motor home parking
brake.
AGS Controller
1. Press the momentary AGS ENABLE switch. The LED indicator above the switch will light.STATUS indicator will display one of three indications: Blinking Green Indicates the system is initiating a generator start sequence (either the TEST or ENABLE switch has been pressed). Solid Green Generator has started successfully. Solid Red After (4) attempts to start, there was a "no start" indicating a problem with the AGS system.
2. A generator "START/STOP" switch is installed on the Command Center Panel command center panel. A second switch is located on the generator, and depending on your motor home model, there may also be a switch installed on the dash.
3. At either "START/STOP" switch, press and hold the upper portion of the switch to start the generator. Depending on the outside temperature, the start process can take up to 15 seconds. Once the generator starts running, release the "START/STOP" switch. The indicator above the switch will light up.
4. For better performance and engine life, especially in colder weather, let the generator engine warm up for two minutes before turning "ON" 120-volt appliances.
5. The small display (hour meter) is used to keep track of run time on the generator. The TEST switch will initiate an automatic generator start/stop sequence. This test attempts to turn on the generator and allow it to run for at least 30 seconds before shutting it off, and is used to confirm that the AGS is configured correctly for your generator type.
The RESET switch will disable the AGS system. The ENABLE and STATUS indicators will go off and the generator (if running will shut off).
86
Maintenance Record
Table of Contents
Section 6: Electrical System
Disengaging the parking brake and turning on the ignition will disable the AGS system if it was previously enabled. To reset it again, the parking brake must be set, and the ignition turned off. The ENABLE switch on the command center panel must be selected again to put the system in automatic start mode.
Solar Prep (if so equipped)
Your motor home may be equipped with a roof mount solar panel quick connection. This allows a (customer purchased) solar panel to be installed permanently on the roof. Installation will consist of the solar panel(s), regulator and wiring/fusing between the regulator and batteries. There are no other solar plugs for portable solar panels on the vehicle.
The (black ABS) solar prep box is located in a basement compartment of the RV and is marked with a solar prep label (indicating wire colors and polarity). There is also an additional label indicating the RV is wired for solar.
When connected, the solar panel will supply power to the battery, the battery will supply power to the converter, and the converter will supply power to all the 12V systems as needed.
Replacing Light Bulbs
Replacement light bulbs must be the same type, voltage and wattage that is listed on the lamp fixture. Use of incorrectly sized bulbs can overload lamp circuits and may create a fire hazard by overheating the fixture. Before replacing a bulb, be sure the light is off.
Maintenance Record
Table of Contents
87
Section 6: Electrical System
Notes:
88
Maintenance Record
Table of Contents
Fuel Safety
Section 7: Fuel System
Automotive fuels can cause serious injury or death if misused or mishandled. If you have further questions, consult your dealer or Customer Service for assistance.
Always shut OFF the vehicle engine while refueling. Do not bring or store fuel or other flammable liquids inside the motor
home because a fire or explosion may result. Before refueling, extinguish all smoking materials and any open flames. Before refueling, always turn OFF all spark producing appliances (i.e.,
water heaters, furnaces, etc.). Do not overfill the fuel tank(s). The pressure in an overfilled fuel tank
may cause leakage and lead to fuel spray and/or fire. Fuel spills represent a serious fire hazard, and should be cleaned up im-
mediately. Never restart an engine or re-light any pilot lights while raw fuel is pres-
ent. FAILURE TO COMPLY COULD RESULT IN FIRE, DEATH OR SERIOUS INJURY.
Fuel Selection Some generators are fueled by the same system used to fuel the chassis engine. Check the generator manufacturer and the chassis manufacturer information to help determine the type of fuel best suited for this dual application.
Fuel Filler Cap
Do not replace the fuel fill cap with one of a different type. Only use a cap specified for your motor home. Use of a substitute cap may create excessive fuel system pressure, resulting in fuel station damage and improper operation in a collision.
Remove the fuel fill cap by slowly turning it counterclockwise, waiting for any "hiss" noise to stop, and then unscrew the cap all the way. To close the fuel fill cap, securely turn the cap clockwise until you hear clicking sounds.
Filling the fuel tank Use care when fueling your motor home. If you spill fuel on the motor home, clean it up immediately. Fuel can dull or soften paint and damage other surfaces.
Maintenance Record
Table of Contents
89
Section 7: Fuel System Exhaust Gas Fumes
Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless.
If you are in a parked motor home with either the engine running or the generator running there is a potential for exhaust fumes to filter back into the motor home.
To avoid breathing exhaust gases, follow these precautions:
Do not run the engine in confined areas, such as a closed garage, any longer than needed to move your motor home in or out of the area.
Windows should be closed while driving or running the generator (if so equipped) to avoid drawing dangerous exhaust gases into the motor home.
If you suspect that exhaust fumes are entering the passenger compartment, have the cause determined and corrected as soon as possible.
If you must drive under these circumstances, close all the windows, and adjust the heating or cooling system to force outside air into the motor home (set the blower on high speed).
The best protection against carbon monoxide entry into the motor home is a properly maintained ventilation system and an active carbon monoxide detector. To allow for proper operation of the motor home ventilation system, keep the ventilation inlet grill(s) clear of snow, leaves or other obstructions at all times.
Maintenance It is recommended that the exhaust system and vehicle body be inspected by a qualified motor home service center:
Each time the engine is ready for an oil change. Whenever a change in the sound of the exhaust is noticed. Whenever the exhaust system, underbody or rear of the vehicle is damaged.
For more information refer to your Chassis Guide.
Propane Gas System (if so equipped)
Propane or LP (liquefied petroleum) gas is an efficient form of energy when proper handling and safety precautions are observed. The propane system in your motor home furnishes the fuel for cooking, heating, hot water and can be an alternative energy source for refrigeration. Propane is heavier than air and tends to flow to lower areas and will sometimes pocket in these low areas, such as the floor. Your motor home is equipped with a propane alarm (refer to Safety Precautions, Combination Carbon Monoxide (CO)/Propane Alarm).
Propane cylinders should not be placed or stored inside the vehicle. LP-gas cylinders are equipped with safety devices that relieve pressure by discharging gas into the atmosphere.
The propane fuel system is comprised of numerous components such as the propane container, hoses, propane gas regulator, piping and copper tubing to each appliance. Your motor home has been carefully tested at the factory and by your selling dealer for leakage. Travel vibrations can loosen fittings. Have the vehicle propane system checked
90
Maintenance Record
Table of Contents
Section 7: Fuel System
at all connections soon after the purchase of your vehicle, and after the initial filling of the propane tanks. Continued periodic checks of the propane system at 5,000 miles of travel (or at least once a year) by a qualified propane service representative as part of your normal maintenance is recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak.
NOTE: All propane lines have been checked with air pressure at the time of manufacture. Dealers are required to recheck and adjust pressure before retail delivery.
The following label should be kept permanently affixed to the motor home:
Propane Gas Container Propane is a true gas compressed into a liquid form. As the fuel is released from the container, it changes to vapor which is then used for the operation of the appliances. Propane will not run through the appliances in the liquid state. A permanently mounted A.S.M.E. approved propane container is located under the floor of the motor home. Propane expands 1½ percent for every ten degrees of increase in temperature. It is imperative to leave sufficient space inside the container to allow for natural expansion of gas during warmer weather.
NOTE: Tanks are to be installed, fueled and maintained in accordance to State and Local codes, rules, regulations or laws.
Maintenance Record
Table of Contents
91
Section 7: Fuel System
Servicing or Filling
Always shut OFF the engine while refueling. Do not smoke and do not operate other ignition sources while refueling.
When the propane container is disconnected from the main supply hose and the P.O.L. connection, install the P.O.L. plastic cap that is attached to the container.
If you suspect your propane container has been overfilled, contact your dealer or a qualified propane technician for assistance immediately. Do not attempt to service a propane container overfill yourself.
Because the container is not removable, the motor home will need to be driven to a qualified propane facility for servicing or filling. Only the authorized gas service technician(s) should be near the motor home while the propane tank is being filled. The new propane container must be carefully purged for proper appliance performance and operation. The propane tank must NEVER BE OVERFILLED. Replace all protective covers and caps on the propane system and/or container after filling. Make sure the valve is closed and the compartment door is securely latched. LP Gas Container Overfill Never allow your propane tank to be filled above the maximum safe level as indicated by the fixed liquid level gauge. Do not allow the visible gauge to be used for filling. Overfilling the propane container above the liquid capacity indicated on the container, could allow liquid propane to enter the system that is designed for vapor only creating a hazardous condition. The following warming label has been placed by the propane container.
Refer to your Warranty Packet for more information on the LP gas system components. Propane Regulator
Propane regulators must always be installed with the regulator vent facing downward. Regulators that are not located in baggage compartments have been equipped with a protective cover. Make sure the regulator vent faces downward and (if applicable) the cover is in place to minimize vent blockage that could result in excessive gas pressure causing fire or explosion.
92
Maintenance Record
Table of Contents
Section 7: Fuel System
NOTE: Regulator appearance and type may vary by model.
Single stage regulator Some models are equipped with a single stage regulator.
Two stage regulator The two-stage regulator has the only moving components in the propane system. Its sole function is to reduce the pressure from the propane containers to a safe and consistent low operating pressure. The first stage reduces the container pressure to 10-13 lbs. The second stage reduces the 10-13 lbs. of pressure further to an operating pressure of 11" W.C. (water column) or 6.35 oz. of outlet pressure to your appliances.
The second stage is adjustable and will need to be adjusted by your dealer or qualified propane service technician for optimum performance (this adjustment should always be made with a properly calibrated manometer).
If the pressure is too high, it affects performance and safety; if the pressure is too low, your appliances will not operate correctly.
If your recreation vehicle is equipped with the "automatic" two-stage regulator, with both cylinders full of propane, turn the lever on the regulator towards the cylinder you wish to use first. This will be the "supply" cylinder and the other the "reserve". Slowly open both cylinder valves. The indicator on top of the regulator will turn bright green. When the cylinder becomes empty, the indicator will change to bright orange. Turn the regulator lever to the side of the "reserve" cylinder and the green signal should return. You may now remove the empty cylinder to have it refilled without interrupting the flow from the full bottle. After filling the cylinder, connect the pigtail hose and slowly open the bottle valve.
Refer to the manufacturer's pamphlet included in your warranty packet and follow all safety instructions and warnings listed.
Propane Use and Safety
Propane is a colorless and odorless gas that, in the liquefied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully perform the procedure listed on the propane system label. This label has been placed in the vehicle near the range for models equipped with a propane system.When a propane container is low, there may be a concentration of an onion or garlic-like odor, which can be mistaken for a propane gas leak. After the propane container has been refueled, the odor will usually disappear. If not, turn off the valve(s) and have the propane system inspected by your dealer or qualified propane service representative.
Propane Leak Test Leaks may be found easily with a soapy water solution.
Do not use a solution containing ammonia or chlorine
when locating leaks. These products are corrosive to copper gas lines and brass fittings, which could result in deterioration of the copper and brass components.Apply the soapy solution to the outside of the gas piping fittings. If a leak is present, the soapy solution will "bubble" at the
Propane System Label
Maintenance Record
Table of Contents
93
Section 7: Fuel System
leak point. If a leak is indicated, shut off the propane system valve(s) and contact your dealer or qualified propane service representative immediately.
Never use an open flame to test for a propane leak. Do not check for leaks using products that contain ammonia or chlorine; these products can cause cracks to form on the metal tubing and brass fittings.
Using the Propane System Use the following steps for propane operation:
1. Close ALL burner valves, controls and pilot light valves.
2. Open the main valve in the propane tank slowly to avoid a rush of propane vapor through the excess flow valve, causing propane "freeze-up." Should you experience propane "freeze-up", close the main valve and wait 15 minutes before trying again.
3. Listen carefully as propane begins to flow. If a hissing noise is heard for more than one or two seconds, close the main valve and contact your dealer to have the propane system tested.
4. Light the appliances as needed and directed in the appliance manufacturer's owner manual located in the Warranty Packet.
Keep the propane container valves closed at all times unless you are using the propane gas system or are having the propane container filled.
Make sure that you read and fully understand ALL safety requirements for handling and operation of the propane system.
The propane system must be handled with care. If you have any questions or concerns, consult with your dealer and/or the specific appliance manufacturer.
If you have double cylinders on your recreation vehicle, use only one at a time. Otherwise, the propane supply will be drawn equally from both cylinders until the supply has been totally exhausted. Using one cylinder until it is empty and then using the second cylinder will allow you to fill the empty cylinder at your convenience without running out of propane. Cooking With Propane Gas
Do not turn gas range burner controls to ON and allow gas to escape before lighting.
Do not use portable fuel burning equipment (i.e., wood and charcoal grills or stoves) inside the recreation vehicle.
Unlike homes, the amount of oxygen supply is limited due to the size of the recreation vehicle. Proper ventilation when using the cooking appliance(s) will help avoid the danger of asphyxiation.
It is especially important that cooking appliances not be used for comfort heating, as the danger of asphyxiation is greater when the appliance is used for long periods of time. FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS INJURY. These warning labels are located in the cooking area to remind the user to provide an adequate supply of fresh air for combustion.
94
Maintenance Record
Table of Contents
Section 7: Fuel System
Ensure a supply of fresh air (Canada units only) Cooking / Comfort Heating Label Calculating Propane Gas Usage Most RV gas appliances are operated intermittently, and each has a different BTU rating. You will need to consider this when planning your propane supply and consumption. Unless there is heavy use of hot water, the water heater consumption of propane is minimal. During cool temperature or high wind conditions, furnace consumption can be extremely high. To calculate your propane supply, take the BTU ratings for your propane appliances and divide that into the BTU availability. Each gallon of propane gas (3.785 liters) produces about 91,500 BTU's (96,528 kilojoules) of heat energy. Propane consumption chart The following chart provides average propane consumption information.
Traveling With Propane
NOTE: Some states prohibit propane appliance operation during travel, especially in underground tunnels. Know the laws for the areas where you travel.
Use care when fueling your motor fuel tanks and/or propane containers. Make certain your propane tank is properly fastened in place.
This label should be kept permanently affixed to your recreation vehicle.
Maintenance Record
Refueling Warning Label
Table of Contents
95
Section 7: Fuel System
Notes:
96
Maintenance Record
Table of Contents
Section 8: Plumbing System
Plumbing System
There are two different water systems in your recreation vehicle:
The fresh water system consists of the fresh water holding tank, faucets and connections, water pump, outside shower assembly (if so equipped), water heater, tub/ shower, and water purification system (if so equipped).
The waste water system consists of the waste water and sewage holding tank(s), drains and toilet.
Plumbing System Maintenance Check all fittings, pressure and waste, for leaks before each trip or before vehicle storage as part of your normal maintenance:
Inspect all faucets, the water purification system (if so equipped) and sink connections (including drain baskets or filters).
Inspect connections at the water pump and water heater. At the end of every trip, you should drain any unused water from the fresh water
system.
All water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors.
The fresh water (potable water) system needs periodic sanitization and winterization to take care of all the components within the plumbing system and help discourage the growth of bacteria and other organisms that can contaminate the water supply.
Typically, there are labels affixed to the exterior of the recreation vehicle sidewall that indicate the locations of the water system drains and fills. Be aware some drain valves may be located inside the vehicle (once the exterior label is found, go inside to find the drain corresponding location).
Refer to the manufacturer's operating manual included in your warranty packet for the detailed operating, sanitizing, and winterizing information for each water system component.
Monitor Panel
Monitor panel locations may vary by model. Typical locations are on the command center panel, on an interior wall, or on the exterior utility center. Some models may be equipped with a touch screen system that monitors tank levels electronically. The monitor panel allows you to monitor the fresh water, grey water, black water and auxiliary battery levels. These functions are controlled using the tact switches. It operates on 12volt DC power supplied by either the converter or auxiliary battery. No power is drawn from the battery unless a switch is pushed or turned ON. Fuses for the monitor panel are located in the load center. Refer to the manufacturer's operators manual for additional information.
Monitor Panel
NOTE: If your RV has secondary black or gray tanks, there may also be an additional tank monitor. located elsewhere in your RV. It is typically
labeled as a convenience center.
Maintenance Record
Table of Contents
97
Section 8: Plumbing System
Operation Press only one tact switch at a time. As you push either the FRESH, BLK GREY1 or GREY2 switch, one or more LED lights will illuminate (from left to right) indicating the content level for that tank. When pushing the "BATT" switch, the LED lights illuminate from left (lowest) to right (highest) to indicate the estimated auxiliary battery condition.
NOTE: When using shore power all 4 LEDs will light. If disconnected from shore power, 3 LEDs will light to indicate a full charge (4th LED may blink).
The LEDs on the panel indicate the following: C= Charge at 12.7 volts G = Good at 12.1 volts F = Fair at 11.6 volts
Command Center (monitor panel appearance and
components may vary)
L = Low at 6.0 volts
Tank monitors on the touch screen have a constant readout. There are no buttons to push. Tank levels are displayed by percentage from 0% to FULL.
The water pump switch (if so equipped) This switch may be located on the monitor panel, the utility center, or both. On some mod-
els, the water pump control may be on one of the selectable screens for the touch screen.
When the water pump switch is ON (lit), the water pump will run until it reaches 45 lbs. of pressure. It will recycle when pressure drops. Turn the switch OFF when the water pump is not being used.
Water heater switch(s) (if so equipped) These switches are located on the monitor panel, or in the case of a touch screen system, on one of the selectable screens of the touch screen. Switches will light up when turned on. The "LP GAS" water heater switch (12V) enables propane operation of the water heater, and the "ELECTRIC switch (120V) enables electric operation of the water heater. Normally both switches should be turned on to provide the fastest hot water recovery time. The water heater can be operated in electric only or gas only modes by pressing each switch independently. If the RV is equipped with a tankless water heater, there will be only an LP Gas switch on the command center panel.
DSI FLT - Direct Spark Ignition Fault (if so equipped) This light located between the water heater switches will indicate a problem with the LP por-
tion of the water heater. When the LP GAS switch is turned on, the light will blink quickly 3 times and the water heater will ignite. The light will then remain off. If the light comes on and stays on, it indicates the gas side of the water heater has not fired and there is a problem with the igniter.
98
Maintenance Record
Table of Contents
Section 8: Plumbing System
NOTE: This light will not appear on touchscreens, RV remote controls or on a WiFi app, only on the Command Center switch panel.
Fresh Water System
All water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (potable water) system needs periodic sanitization and winterization to take care of all the components in the plumbing system to discourage the growth of bacteria and other organisms that can contaminate the water supply.
DO NOT drink water deemed microbiologically unsafe or of unknown quality.
Never travel with full fresh, black or grey water holding tanks.
Water Pressure Regulator (customer supplied)
A water pressure regulator is recommended to prevent damage to the plumbing system or components. To prevent damage when using the city water connection, a 45 lb. (315 KPa) rated water pressure regulator is recommended.
Excessive pressure from the water supply source may be encountered in some parks, especially in mountain regions when using the fresh water inlet or black tank flush. Water pressure regulators are available to protect your recreational vehicles plumbing system against such high pressure.
Fresh Water Holding Tank There may be several ways to fill the fresh water tank depending on the model. For details of each method, refer to the Fresh Water Connections or the Utility Center (if so equipped) sections. There are plastic overflow tubes in the fresh water holding tank which allow water to flow out of the water tank (see City Water Fill). Occasionally, there may be water coming from the overflow tubes when the fresh water holding tank is filled. This is normal and can be a result of the recreation vehicle being parked on an incline, or the motion caused by starting or stopping during travel.
Do not cap, block or modify the fresh water tank overflow tubes in any way. Enough water pressure can build up during the filling process to damage the plumbing system if the overflow tubes are obstructed.
Be careful not to overfill the fresh water holding tank. It can pressurize the tank, causing leakage and water damage and void the warranty. DO
NOT leave the tank unattended while filling.
Maintenance Record
Table of Contents
99
Section 8: Plumbing System
12-volt Water Pump and Switch There must be sufficient 12-volt DC power to run the water pump when your recreation vehicle is not hooked up to city water. Once activated, the water pump (also known as the demand pump) will self-prime, and provide water. The pump is designed for intermittent use only. Using the pump continuously or with high pressure will shorten the life of the pump and is not covered in your warranty.
Periodically check the in-line water pump strainer for accumulated debris. To clean, shut off the water pump, unscrew the clear cap, remove the re-useable metal strainer, clear any debris, then reinstall.
For additional information on the care and operation of the pump, read the safety and operating information in the pump manufacturer's owner's manual.
Water Pump Switch (if so equipped) Most water pump switches illuminate when the water pump is activated. Typical switch locations are in the back of the unit or on the monitor panel. When the water pump switch is ON the pump runs until 45 lbs. of pressure has been achieved. The red light will stay on. The water pump automatically recycles when pressure drops. Some cycling may occur depending on the volume of water being released. Turn the water pump switch OFF when it is not in use.
NOTE: In some models the water pump switch will be a black rocker switch located near the sink cabinet
The water pump switch should be in the OFF position when the RV is left unattended for any amount of time. If something would happen to the water system, this may help limit water damage to a smaller area.
Water Purification System (if so equipped)
If the water supply has not been used for some time, allow the water to flow for several minutes to flush the system.
Filters should be replaced at the beginning of each camping season or if they have come into contact with contaminated water.
When not in use, the water filter cartridge should be stored out of freezing temperatures. RV antifreeze will damage the water filter cartridge.
Filter canister is typically located in a compartment behind the utility center.
To Replace Canister Filter Cartridge
1. Turn off water supply using two valves located on the water lines on
each side of the canister. Water pump should be OFF.
2. Place drip pan below filter housing to catch any spillage.
3. Press the red button on top of the filter housing to release pressure.
4. Using a spanner wrench, rotate the filter housing. Unscrew the housing
completely, dump water out and remove the filter (dispose of the old
filter properly).
5. Clean the inside of the filter housing with mild detergent. Thoroughly
rinse and wipe clean.
Filter Housing
100
Maintenance Record
Table of Contents
Section 8: Plumbing System
6. Remove the O-ring from the groove in the housing and wipe clean. Coat with petroleum jelly.
7. Replace the O-ring in the groove, making sure it is properly seated. 8. Install the new filter cartridge. 9. Replace the canister housing (hand tighten is normally sufficient). 10. Turn on the water supply, turn the pump ON, open a faucet and check for leaks. Turn
the pump OFF afterwards.
NOTE: There is no bypass feature on a canister style water filter. The water filter must be removed before sanitizing or winterizing the RV.
Each new recreational vehicle is winterized with RV antifreeze before it is shipped to the dealer. To use the water purification system, full system canister water lines need to be flushed of antifreeze and then the filter installed in the canister before use. Refer to the manufacturer's owner's manual and the label on the water filter cartridge for further information.
Do not allow water in the canister housing to freeze. Remove the filter before using anti-freeze to winterize the system or
chlorine solution to sanitize the system.
Flush canister housing thoroughly before it is put back into service after winterizing or sanitizing.
For best results replace filter every 6-12 months. Do not use carbon cartridges where water is microbiologically unsafe or
of unknown quality.
Maximum operating pressure is 125 psi (8.75 bar). Maximum water temperature is 125° F (52° C).
Draining The Fresh Water System
Water tanks may be drained through a valve located near the tank. A recreational vehicle with a demand pressure pump system will have low-point drains attached to the water lines (normally located near the water tank).
These low-point drains will release water in the supply lines by opening the valves and all faucets. The water heater has its own drain plug. To drain the permanent fresh water holding tank and supply lines:
1. Turn the water heater power OFF (turn off the electric and LP gas switches).
2. Open all faucets, including the outside shower faucet (if so equipped).
3. Open the "fresh tank drain" valve. All fresh water tanks can be
drained by one of two types of drain valves. A white plastic drain is
attached to the exterior wall or a valve located inside the RV adjacent Exterior Fresh
to the water tank (turn 45° to open or close).
Water Drain
4. Open the "low point drains" by turning, then pulling the handles up. They are installed at the lowest point of the water lines. A label is placed on the outside of the RV to indicate where the drains are located. The drains will need to be operated from inside the
Maintenance Record
Table of Contents
101
Section 8: Plumbing System
RV. Once the label is found on the exterior sidewall, the drains will be found at a corresponding location in the interior. 5. Drain the sink by removing the drain cap. 6. Turn ON the water pump and allow it to run as needed. 7. If the RV water heater has bypass valves, set them to the BYPASS configuration (refer to the Water Heater Bypass section). Low Point Drains 8. Operate the toilet flush lever until water stops flowing. 9. Relieve the water pressure using the P&T valve BEFORE removing the water heater drain plug. If there is any water pressure present, the water will spray out of the opening when the drain plug is removed. When you are finished draining the fresh water system, reverse these steps and dump the grey and black water holding tanks. It is normal for some liquid to remain in the fresh water tank after drainage procedure.
Uni-Dock Utility Center
When using the fresh water system, always use a non-toxic drinking water hose dedicated only to supplying fresh water. To prevent contamination, keep the drinking water hose from coming into contact with the ground. Install the city water connection inlet cap when the fresh water connection is not being used. The fresh water connection should be disconnected (i.e., the non-toxic drinking hose disconnected) when the recreation vehicle is unattended for any amount of time.
Never leave the motor home unattended while filling the fresh water system.
Do not remove this label from your motor home.
Potable Water Label (Label appearance may vary)
102
Maintenance Record
Table of Contents
Section 8: Plumbing System
The Uni-Doc Utility Center is located in an exterior compartment and allows you to perform the following functions:
Power fill the fresh water tank for remote or dry camping Use the pump to supply water to fixtures from the fresh water tank Use the pump to siphon fill or sanitize the fresh water tank from a container Connect to city water to supply water to RV fixtures Winterize plumbing lines and fixtures Bypass the hot water heater when winterizing to avoid damage to the water heater Rinse the black tank to help control odors and prevent waste buildup Rinse off items outside the unit with hot/cold faucet Connect up to (3) coax lines with satellite, cable and auxiliary The city water connection inlet is located in the Uni-Dock utility center. Nautilus - 4 Valve Position and Routing Information White Handle: Receives water from water inlet on the front panel. Sideways: Water goes to pump inlet. Downward: Water goes into the blue handled diverter. Blue Handle: Receives water from the white handle valve/water inlet on the front panel. Sideways: Water goes to or comes from the fresh water tank. Downward: Water goes out to the fixtures (cold). Red Handle: Receives water from the cold water supply. Sideways: Water goes to hot water fixtures without going through hot water heater. Upwards: Water goes to hot water heater. Green Handle: Receives water from the pump. Sideways: Water goes to fresh water tank. Upwards: Water goes to fixtures. Using the Uni-Doc utility center:
A check valve is located inside the city water connection inlet on the utility center. NEVER depress the check valve on the "CITY WATER CONNECTION" inlet with pressure in the line. It will cause irreparable damage to the valve function and the inlet will leak water.
The following information details the functions of the utility center water valves as displayed on the valve operation label.
POWER FILL TANK (pressurized fresh water source) 1. Connect the fresh water hose to the City water connection inlet on the utility center.
2. Set the color coded valves to POWER FILL TANK setting: (A) White handle pointing down (B) Blue handle pointing down
Maintenance Record
Table of Contents
103
Section 8: Plumbing System
(C) Green handle pointing left (D) Red handle pointing up 3. Connect the other end of the hose to a pressurized fresh water source (faucet or spigot). 4. Turn the pressurized water source ON, the tank should begin filling. 5. When water has reached the desired level, turn the pressurized water source OFF. DO NOT OVERFILL. Tank level can be viewed on the monitor panel inside the RV. 6. Disconnect water source from the spigot/faucet first, then disconnect from the city water fill inlet on the utility center. DRY CAMPING (pump supplies water from the fresh water tank) 1. Make sure the fresh water tank has an adequate supply of water. 2. Set the color coded valves to the DRY CAMPING setting: (A) White handle pointing right (B) Blue handle pointing left (C) Green handle pointing up (D) Red handle pointing up 3. Turn the pump switch ON. 4. Water should be available to all fixtures. 5. Turn pump OFF when water is not being used.
NOTE: TTo fill the fresh water tank without a pressurized water source, refer to SANITIZE (Siphon Fill) section, and use a container holding fresh potable water and a hose. Water will be drawn into the tank by the pump. There is no gravity fill inlet on the recreation vehicle. DO NOT OVERFILL THE TANK!
CITY WATER (pressurized fresh water source) 1. Connect the fresh water hose to the city water inlet. 2. Set the color coded valves to the CITY WATER setting:
(A) White handle pointing down (B) Blue handle pointing left (C) Green handle pointing left (D) Red handle pointing right 3. Connect other end of the hose to the pressurized fresh water source. 4. Turn ON the pressurized water source. 5. Water should now be available to all fixtures. Turn off water at the pressurized source first, disconnect hose from the water source, then disconnect the hose at the city water connection on utility center.
Sanitizing The Plumbing System When to sanitize:
When your RV is new. At the beginning and end of each season. Every three months of use. When the water system becomes contaminated.
104
Maintenance Record
Table of Contents
Section 8: Plumbing System
How to Sanitize 1. Turn water heater power OFF (both electric and LP gas on stan-
dard storage water heater). Single switch is inside the RV for the tankless water heater. Set the colored valves to SANITIZE as indicated on the utility center label. This automatically bypasses the water heater. 2. Level the recreational vehicle and drain the fresh water system. (see Draining the Fresh Water System). 3. Close the low point drain valves and the fresh water tank drain valve. Full System Canister water filter (if so equipped): Remove the canister, take the filter out of the canister, then reattach the empty canister. Bypass the cartridge water filter (if so equipped): Use the clear plastic tube (supplied with RV) to bypass the water filter. 4. Prepare a chlorine solution using 1/4 cup of household bleach to one gallon (3.785 liters) of water in a container. Prepare one gallon of solution for every 15 gallons of tank capacity. This will result in a residual chlorine concentration of 50 ppm in the water system. If a 100-ppm concentration is required, use ½ cup of household bleach with one gallon of water. One gallon of the solution should be used for each 15 gallons of tank capacity.
NOTE: Fresh water tank sizes vary by model. Contact your dealer or Customer Service for your specific tank size.
5. Siphon the sanitizer solution into the fresh water tank; attach a hose to the city water connection inlet. Insert the other end of the hose into a container holding the chlorine solution. Do not use the non-toxic drinking water hose.
6. Turn the pump switch ON (red LED will light). The solution will be drawn into the fresh water tank. Turn the pump OFF when solution has been drawn into the tank. To aid in siphoning, set the container on a surface approximately (2) feet off the ground. The drain valves must be turned OFF.
7. Remove the chlorine container and finish filling the fresh water tank with clean (potable) water until the tank is full. Tank level can be viewed on the monitor panel inside the RV. Keep the valves set on SANITIZE. Leave the hose attached to the city water connection inlet and place other end of hose in a container of fresh water. Turn the pump ON. Fresh water will be siphoned into the tank. Turn pump OFF when tank is full. Disconnect the hose from utility center.
8. After the recommended amount of sanitizing solution is in the tank make sure the water tank is full of fresh water, the cartridge water filter (if so equipped) is bypassed or the filter is removed from the full system canister water filter (if so equipped), and power to water heater is turned OFF (both electric and LP gas). Set the valves to DRY CAMPING setting. Turn the pump ON and sanitized water will flow into the water lines from the tank when a fixture is opened.
9. Open all hot water faucets one by one until water begins to flow continuously and a chlorine smell is noticeable. Include outside shower faucets (if so equipped). Close hot water faucets. Repeat process with the cold water faucets.
Maintenance Record
Table of Contents
105
Section 8: Plumbing System
10. Turn OFF the water pump. 11. Let the solution remain in the tank and lines for at least four hours when disinfecting
with 50-PPM residual chlorine. If a shorter time is desired, a 100-PPM chlorine concentration should used for at least one hour
NOTE: To thoroughly sanitize the fresh water tank, the unit should be driven around for a period of time allowing the solution to splash the sides and top of the tank.
12. After the required period, drain the chlorine solution from the fresh water system. 13. Fill the fresh water tank full of clean (potable) water. Use water from either a pressur-
ized source, or from a container (as detailed below). Filling from a pressurized source: Set the valves to the POWER FILL TANK setting. Connect a non-toxic drinking hose to the city water connection inlet. Connect the other end of the hose to the pressurized water source. Turn on the water source to draw water into tank until full (Do Not Overfill). Disconnect the hose from the water source first, then from the utility panel. Syphon filling from a water container: Set the valves to the SANITIZE setting. Insert a hose into the city water connection inlet; place the other end of the hose in a container of water. Turn the pump ON to draw water into the tank until full (Do Not Overfill). Remove the hose and the container. To aid in siphoning place the container on a surface approximately (2) feet off the ground. Drain valves must be off.. 14. Power to water heater should be OFF (electric and LP Gas switches on standard storage water heater). Single switch is inside the RV for the tankless water heater. When the fresh water tank is full, set the valves to the DRY CAMPING setting. Turn the pump ON to send water through the lines. 15. Run water through all faucets (hot and cold, including outside shower) until chlorine smell is gone. Turn faucets and outside shower off, turn pump OFF. 16. Drain the fresh water system again. If the RV has the full system canister water filter, remove the canister, reinstall the filter, and reattach the canister. 17. Refill the fresh water tank with fresh water again and when water heater is full of water, turn the water heater power ON. SANITIZE (or Siphon Fill) the Fresh Water Tank via Pump
NOTE: Refer to the Sanitizing Plumbing System section before starting this process.
1. Connect a garden hose to the city water inlet (do not use your fresh water hose to sanitize the water lines or the tank).
106
Maintenance Record
Table of Contents
Section 8: Plumbing System
2. Set the colored coded valves to the SANITIZE setting: (A) White handle pointing right
(B) Blue handle pointing down
(C) Green handle pointing left
(D) Red handle pointing up
The water heater is automatically bypassed on this setting.
3. Place the other end of the hose in a container holding sanitizing solution. 4. Turn the pump switch ON. A red LED will light under the switch. 5. Sanitizing solution should be drawn out of the container and into the water tank. To aid
siphoning place the container on a surface approximately (2) feet off the ground. DO NOT OVERFILL. Tank level can be viewed on monitor panel inside the RV. 6. Siphon all sanitizing solution out of the container and into the water tank. 7. Turn the pump Switch OFF. 8. Disconnect the garden hose from the city water fill inlet on the utility center. Lingering Chlorine Taste: If a chlorine taste lingers in the water, flush the water system with a solution consisting of one-quart vinegar to five gallons of clean water. Re-flush as necessary. The vinegar solution may damage the water heater or the water filter, so both must be bypassed again before performing this operation.
Follow the steps outlined in Draining the Fresh Water System with one exception, do not drain the water heater. Do not remove the water heater drain plug.
For the full system canister water filter: remove the canister, take out the filter, then reattach the empty canister.
After draining the system: 1. Water heater power should still be OFF (both electric and LP
Gas on standard storage water heater). Single switch is inside the RV for the tankless water heater. 2. Put the vinegar solution into the fresh water tank and set the valves to the SANITIZE setting. Attach a hose to the city water fill inlet. Put the other end of the hose in a container with the vinegar solution. Turn the pump ON.
The solution will be drawn into the fresh water tank (the water heater will be bypassed automatically). When the container is empty, turn pump OFF, and disconnect hose from utility panel.
To aid in siphoning, place the container approximately (2) feet off the ground. The drain valves must be closed.
3. Fill the fresh water tank full of clean (potable) water. Use water from either a pressurized source, or from a container (as detailed below). Filling from a pressurized source: Set the valves to the POWER FILL TANK setting. Connect a non-toxic drinking hose to the city water fill inlet. Connect the other end of the hose to the pressurized water source. Turn on the water source and fill until is full (Do Not Overfill). Disconnect the hose from the water source first, then disconnect from the utility panel. Syphon filling from a water container: Set the valves to the SANITIZE setting. Insert a hose into the city water fill inlet, place other end of the hose in a container of water.
Maintenance Record
Table of Contents
107
Section 8: Plumbing System
Turn pump ON to draw water into the tank until tank (Do Not Overfill). Remove the hose and the container. To aid in siphoning place the container approximately (2) feet off the ground. The drain valves must be closed. 4. Run water through all faucets (hot and cold, including outside shower) until chlorine smell is gone. Set the valves to the DRY CAMPING setting. Turn the pump ON to send water through the lines. 5. Close all faucets including outside shower. Turn pump OFF. 6. Drain the system again, but do not drain the water heater (water heater power still OFF). 7. Close low point drains and fresh water tank drain. 8. Refill the fresh water tank with clean potable water. Use the city water fill connection inlet and one of the methods listed in Step 3. 9. Open faucets and check that the chlorine taste is gone. 10. Drain the system one more time. 11. Remove the clear tube and replace the cartridge filter (if so equipped), or remove full system canister, insert filter, and reattach canister to the mount. 12. Refill the fresh water system with clean water. After filling the water tank, set the valves to either DRY CAMPING or CITY WATER in order for water to flow through all fixtures in the plumbing system. Water heater power can be restored (storage type water heater must be full of water). Winterizing the Plumbing System Preparing your recreation vehicle for colder weather or storage is very important. Failure to prepare your RV may cause water supply lines and the water heater to freeze. The RV should be winterized at the end of the camping season or when it will be exposed to temperatures that will fall at or below 32°F (0°C). Repairs due to freezing are not covered by warranty.
NOTE: The winterization process may vary slightly due to different plumbing configurations between models.
NOTE: Appliances (refrigerator, dishwasher or clothes washer) must be winterized. Refer to the appliance owner's manual for additional information or contact your Dealer or Customer Service for assistance.
If your RV is equipped with a residential style refrigerator, there may be a winterizing instruction sheet included in your Warranty Packet. If you chose to perform the winterization process yourself, read and understand the following information before starting. Contact customer service or your dealer for questions about this process. Refer to the P3 Uni-Dock Utility System section for valve settings. It may be easier to winterize the RV with another person to assist you.
108
Maintenance Record
Table of Contents
Section 8: Plumbing System
NOTE: The water heater must be drained to prevent damage from freezing. The valves on the P3 utility center automatically bypass the water heater. Do not drain the water heater while it is hot or under pressure! Antifreeze should be kept out of the water heater.
Refer to Sanitizing the Plumbing System section for an explanation of docking station valve positioning and routing information. Winterize with Air Pressure This method uses compressed air to blow out any remaining water in the system after initially draining water using drain valves. Tools required would be an air compressor and a blowout plug.
Before applying air pressure to the utility center, 4 colored valves (WHITE, RED, GREEN, BLUE) MUST be set to 45° or damage may occur to the utility center. Never apply air pressure to the water system with any valves in the closed position. Air pressure applied to a closed valve, faucet or low point drain could potentially damage the seals and cause water leaks. If you have questions, consult your RV dealer. Using RV antifreeze is the preferred method of winterization. Recommended air pressure is 30 PSI MAX. Exceeding this pressure may rupture water line couplings and void your warranty.
1. Turn off water heater gas valve, typically located outside the RV. Water heater power should be OFF (both electric and LP Gas switches). Single switch is inside the RV for the tankless water heater (if equipped).
2. The Uni-Doc utility center has no dedicated water heater bypass valves. This function is built into the utility center.
3. Level the RV and drain the fresh water tank, the tank (storage) water heater and the hot and cold water lines. Open all low point drains and the fresh water tank drain. Faucets inside the RV should be opened to relieve pressure to allow water lines to drain. Refer to Draining the Fresh Water System section.
4. Remove the drain plug from the tank (storage) water heater located outside the RV (Fig 1). Do not remove the drain plug if the water heater is hot or under pressure. Release pressure and let it cool.
5. To drain a tankless water heater (if so equipped), open water faucets and use compressed air at the City Water Connection on the utility center. There is no drain plug.
6. Water filter should be removed for winterizing. See Water Purification System section. Your RV may have one of two types of filters:
Maintenance Record
Table of Contents
109
Section 8: Plumbing System
Full System Canister Filter: Remove the canister, take out the filter and re-attach the empty canister. Cartridge Water Filter: Remove the cartridge filter and replace it with a bypass hose (supplied with your RV).
NOTE: Filters should be replaced at the beginning of the camping season or if they have been exposed to contaminated water or antifreeze..
7. Turn the (color) valve handles to the POWERFILL position. 8. Low point drains should be open to remove water from the lines. 9. Open all faucets in the RV. If there is an outside shower, attach the shower hose to the
shower, and open shower faucets. 10. Drain plug should be removed from tank (storage) water heater. 11. Run the water pump until pump is dry (approximately 15 to 20 seconds). Do not oper-
ate pump longer than that without water as it can damage the pump. 12. After water is drained from the lines, turn the Red,
Blue, Green and White valves so they are at 45° (Fig 2). 13. Attach a blowout plug to the City Water Inlet on the utility center panel (Fig 2). 14. Attach the air hose to the blowout plug. Set the compressor to 30 PSI. Set the four-color valves to 45° angle (Fig 2). Red, Blue, Green and White valves must be set at 45° before applying air pressure 30 PSI Max. 15. Blow air into the utility center (30 PSI Max). Water lines should be clear in 5 to 10 minutes. 16. Turn off air supply; remove air hose and blowout plug. 17. Close low point drains; replace the water heater drain plug. Tankless water heater should now be purged of water. 18. Set the colored valves to the WINTERIZE positions. 19. Pour one cup of RV antifreeze in all drain P-traps (sinks and bathtub). Winterize the Black Tank Flush 1. Connect the blowout plug to the Black Tank Flush inlet at the utility center panel. 2. Colored valves have no effect on the black tank flush inlet. 3. Connect the air hose to the blowout plug. Set the compressor to 30 PSI maximum. 4. Make sure the black tank has been emptied. Open the black tank drain gate valve. 5. Blow air into the flush inlet for 30 to 60 seconds. 6. Disconnect the air hose, compressor and blowout plug. 7. Close the black tank drain gate valve (typically under the RV). The preferred method to winterize your recreation vehicle is by using RV antifreeze in the plumbing system. It may be easier to winterize the RV with another person to assist you.
110
Maintenance Record
Table of Contents
Section 8: Plumbing System
If the recreation vehicle is going to be stored in a non-temperature controlled environment with a risk of temperatures reaching 32°F (0°C) or lower, the plumbing system must be winterized with RV antifreeze. Repairs due to freezing are not covered under the terms of the Towable Limited Warranty.
WINTERIZE (plumbing lines and fixtures via pump)
NOTE: For complete winterizing instructions refer to the Winterizing the Plumbing System section.
1. Connect a garden hose to the city water inlet (do not use fresh water hose). 2. Set the color coded valves to the WINTERIZE setting:
(A) White handle pointing right (B) Blue handle pointing left (C) Green handle pointing left (D) Red handle pointing right The water heater is bypassed automatically on this setting. 3. Insert the other end of the hose in a container holding RV antifreeze. 4. Turn the pump switch ON. 5. Antifreeze should begin flowing into the plumbing lines and fixtures (pump will run when a faucet or the toilet is in use). To aid in siphoning place the container on a surface approximately (2) feet off the ground. 6. Open one plumbing fixture, keeping it open until antifreeze appears then close it. Repeat for each plumbing fixture (including the outside shower hot and cold lines). 7. Turn the pump OFF when all fixtures have been winterized. 8. Disconnect the hose from the city water connection inlet (it is normal for some antifreeze to exit the inlet hose as it is being disconnected). 9. Leave the valves set on WINTERIZE setting. Winterize with Antifreeze Method
Automotive antifreeze (ethylene glycol) and windshield washer antifreeze (methanol) are poisonous. Never use these products in your fresh water system. These products are harmful and may be fatal if swallowed. Use only RV antifreeze.
This method requires non-toxic RV antifreeze in the water lines and does not require any special tools. Use ONLY RV ANTIFREEZE in your fresh water system for freeze protection.No other product or commodity should be used. Antifreeze should never enter the water heater, RV water filter, refrigerator, refrigerator water filter, or fresh water tank.
1. Turn water heater power OFF (both electric and LP gas switches inside the RV for storage type water heater). The water heater should never be drained when HOT or under pressure.
Maintenance Record
Table of Contents
111
Section 8: Plumbing System
2. Level the RV and drain the fresh water plumbing system. Refer to Draining the Fresh Water System.
3. Water heater should be empty after draining the plumbing system. 4. If your motor home has a standard storage type water heater you must remove the drain
plug to drain the water heater (Fig 1). 5. Replace the water filter cartridge with the plastic bypass hose. 6. On full system canister water filters (if so equipped), remove the canister, take out the
filter, and reattach the empty canister. 7. Make sure the fresh water tank drain and low point drains are closed. This includes the
refrigerator/washer low point drains (if equipped). 8. Set the water valves to WINTERIZE setting and connect a
hose to the City Water Inlet. Insert the other end of the hose into a container of RV antifreeze. Turn the pump ON with the pump switch. Antifreeze will be drawn into the water lines and fixtures (pump only runs when a faucet or fixture is open).
NOTE: When set to WINTERIZE, antifreeze will not enter the water heater or the fresh water tank. There are no dedicated water heater bypass valves.
9. Open the hot water line faucets (kitchen/bath sinks, shower and outside shower (if equipped) until RV antifreeze begins to flow continuously.
10. Close the hot water line faucets and repeat with the cold water line faucets (kitchen/ bath sinks, shower and outside shower). Flush the toilet several times until you see antifreeze in the bowl.
When you are finished adding RV antifreeze 11. Turn the water pump OFF with the switch on the utility center panel. 12. Colored valves should remain in the WINTERIZE positions. 13. Remove hose and container from the City Water Fill inlet. Put cap back on the City
Water Fill inlet. Leave the valves in WINTERIZE position. 14. Pour 1 cup of RV antifreeze into any/all drain P traps (sinks and bathtub). 15. Wipe any RV antifreeze out of the sinks, shower (or tub), toilet, washing machine tub,
and dishwasher tub with a soft, dry cloth.
Water can accumulate in the flexible hose and dump connector of the macerator system. When winterizing the RV, antifreeze must be added to the macerator system.
Contact your dealer if you require further assistance. Winterize the Macerator System (if so equipped) Ensure all tanks are empty. 1. Pour RV antifreeze into the toilet and down into the black water tank.
112
Maintenance Record
Table of Contents
Section 8: Plumbing System
NOTE: Use a container (bucket) for capturing system fluid.
2. Turn the macerator pump ON. 3. Run the pump until antifreeze begins to discharge from the dump connector attached
to the flex hose. 4. Turn the macerator pump OFF. 5. Drain the flex hose by holding it at a sloped angle to drain excess water and return the
hose to the storage location. 6. As an added safety measure, open the Macerator Bypass valve and let it drain. The
bypass valve may be either at the utility center or under the RV. De-winterize the macerator system Emptying the black tanks in the spring will flush antifreeze out of the macerator system.
Water Heater
Hydrogen gas may result if you have not used the water heater for two weeks or more. HYDROGEN GAS IS EXTREMELY FLAMMABLE. To reduce the risk of injury under these conditions, open the hot water faucet for several minutes at the kitchen sink before you use any
electrical appliance connected to the hot water system. If hydrogen is
present, you may hear what sounds like air escaping through the pipe as the water begins to flow. Hydrogen gas may be present even after water has been drained from the water heater tank. Open the faucet at the sink and allow the system to vent for five to ten minutes. Do not smoke or have any open flame near the open faucet while venting. On DSI water heater models, make sure the switch is OFF.
Do not alter the operation or change the design/construction of your water heater. For your safety, only factory authorized parts should be used
on your water heater. Accessories marketed for recreation vehicles, such
as an "add-on" electric heating elements, are not recommended by the
manufacturer. Such items are not approved to be installed and could
create an unsafe condition and will void all warranties.
If you smell propane gas then STOP! and follow the procedures listed in the Propane System section before attempting to operate the water
heater.
Maintenance Record
Table of Contents
113
Section 8: Plumbing System
The water heater manufacturer has preset the sensing limit to maintain the water temperature when the water heater is activated. Read the safety and operating information provided in the manufacturer's manual located in your warranty packet before attempting to activate the water heater.Operating Instructions Make sure the water heater is filled with water before use as even momentary operation of the water heater without water in it may result in damage to the tank heating element and/or controls. Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water heater. Double check the bypass valves, make sure they are set properly. Water Heater Switch (if so equipped) The "propane GAS" switch enables propane operation of the water heater, and the "ELECTRIC" switch enables electric operation. NOTE: Water heaters in certain models will ONLY have a single LP Gas water heater switch. These units will not heat water electrically. Water Heater Bypass Use the factory installed water heater bypass, available in most floor plans, to avoid filling the entire water heater with RV antifreeze. See the Utility Center section for details on using the bypass system. High Altitude Deration Operation of the water heater at high altitudes may require derating. If the water heater is not properly derated, lack of sufficient oxygen for combustion may produce improper burner operation. Pilot outage caused by burner lift-off or sooting from a yellow burner may occur, indicating the possibility of carbon monoxide. You may also notice a lack of efficiency in heating the water because of incomplete combustion of the burner at these higher altitudes. Consult with the local propane company, your dealer or the water heater manufacturer for proper derating of the water heater. Change out of the orifice (derating) should be done by the dealer or a qualified service agency.
NOTE: It is important that once the RV has returned to lower elevation (below 4500 feet) any high altitude deration or other adjustments be reversed for proper operation of the water heater.
Pressure and Temperature Relief Valve
Do not place a valve between the pressure and temperature (P&T) valve and the tank. Do not remove or plug the relief valve under any circumstances.
The temperature and pressure relief valve is designed to open if the temperature of the water within the heater reaches 120° F, or if the water pressure in the heater reaches 150 pounds. When this pressure is reached, the pressure relief valve will open and water will drip from the valve.
This "weeping" or dripping will continue until the pressure is reduced to below 150 pounds, and the valve closes. This condition is normal and does not indicate a defective relief valve. One way to reduce the frequency of this occurrence is to maintain an air pocket at the top of the water heater tank. This air pocket will form in the tank by design; however, it will be
114
Maintenance Record
Table of Contents
Section 8: Plumbing System
reduced over time by the everyday use of your water heater. To replenish this air pocket: 1. Turn off the water heater. 2. Turn off the cold water supply line. 3. Open a faucet in the recreation vehicle. 4. Pull out the handle of the pressure relief (P&T) valve and allow water to flow from the
valve until it stops. 5. Release the handle on the P&T valve - it should snap closed. Close the faucet and turn on the cold water supply. As the tank fills, the air pocket will develop. Repeat this procedure as often as needed to reduce the frequency of the weeping P&T valve. Draining and Winterization If the recreation vehicle is to be stored over the winter months, the water heater must be drained to prevent damage from freezing. Damage to the water heater caused by freezing is not warrantable. It is recommended the water heater be drained and bypassed during the winterization process, particularly if introducing RV antifreeze into the plumbing system. Never drain the water heater when it is HOT or UNDER PRESSURE.
Outside Shower and Courtesy Light
A handheld shower assembly with both hot and cold water is available in the utility center for washing or rinsing. The coiled hose for the shower has a quick connect fitting that attaches between the shower control knobs. Be sure the 12 volt power for the water pump is on, or the city water connector has water available to it. Water should always be turned off using the hot / cold control knobs rather than turning off the water with the lever on the shower head. Turning off the water with the shower head lever can create a condition where the hot and cold water will mix through the outside shower faucet, thereby reducing the temperature of the hot water. It can appear as though the hot water heater is not working properly. After the water has been allowed to drain from the shower head, replace it in the exterior universal docking center. The courtesy light is operated with a rocker switch located on the utility center panel.
NOTE: Any remaining water in the shower hose will drip or run out; this is not a leak but performs as intended.
Faucets
The bathroom, kitchen and outside shower faucets operate much the same way as the faucets in your home. Make sure there is sufficient water available and the 12-volt water pump is turned ON before operating.
NOTE: There may be air in the water plumbing lines which needs to be bled out before a steady stream of water comes from the faucet.
Maintenance Record
Table of Contents
115
Section 8: Plumbing System
Bathroom Tub / Shower
Keep the water heater and holding tank capacities in mind when using the fresh water system. The used water will drain through the plumbing pipes into the grey water holding tank.
Be sure the water heater is ON and had sufficient time to heat the water. If dry camping, be sure your 12-volt water pump is ON. Unlike your home, the recreational vehicle does not contain a water pressure balance valve. If someone is using the shower, it is recommended that the fresh water system NOT BE USED until they are finished.
Water temperatures over 125°F (49°C) can cause severe burns instantly therefore, be careful when using hot water. Always test the water temperature before showering or washing.
The shower faucet may include a vacuum breaker for the shower. There are two purposes for this breaker:
To prevent siphoning water through the hose from another fixture. To prevent water from being retained in the hose. The showerhead DOES NOT have a complete shut-off valve (the complete shut-off is at the faucet). The showerhead may drip slightly in the OFF position after use; this is normal and does not indicate a leak or defect.
Maintenance Refer the manufacturer's user guide or label instructions for detailed cleaning information. The tub/shower walls are made of ABS plastic material. Use a mild detergent soap and warm
Black/Grey Water System and Tanks
Water from the sinks and shower flows into the gray water (or wastewater) holding tank. Water from the toilet will flow into the black water (or sewage) holding tank (see Black/Grey Water Holding Tanks).
Drain Pipes with P-Trap (if so equipped) The drain pipes may be equipped with a "P-trap" installed to help prevent odors from escaping into the RV. During travel, water from the P-traps may spill and permit odors into the RV. By adding water and using a RV approved deodorizing agent you will dissolve the contents faster and will keep the drain lines and tanks clean and free flowing. These chemicals are available at an RV supply store or your dealer.
Drain Pipes with Dry Sealing Valve (if so equipped) Your RV may be equipped with a dry sealing valve that prevents the escape of odors from your waste system and eliminates the need for P-traps. Should the RV drain piping system become clogged, it is important that the dry valve be removed before passing a mechanical cleanout tool through the piping to open the drain. Passing a cleanout tool through the waterless valve may cause damage to the internal seal that may potentially allow sewer gases to escape into the RV interior. The waterless trap can be unscrewed from the water lines. A label has been placed near the location of the waste valve that reads as follows:
116
Maintenance Record
Table of Contents
Section 8: Plumbing System
REMOVE WATERLESS TRAP BEFORE USING MECHANICAL DRAIN CLEANING DEVICES
Sewer Hose Storage Depending on your RV model, the sewer drain hose may be stored in an exterior compartment marked "Sewer Hose" or it may be located in the hollow square tube bumper. The bumper has removable plastic end caps, and the hose slides inside the hollow bumper. Vents Vent pipes and vents release air from the grey and black water holding tanks. On most models the exterior vent cap is attached to the roof and must be kept clear of obstructions to perform as intended. On some models, the vent pipe may be part of the drainage system referred to as a "wet vent" where water flows downward as air flows upward in the same pipe. Some models are equipped with a side vent system. On these models this label will be next to the termination valve. This label should not be removed from your recreation vehicle. Black/Grey Water Holding Tanks Dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight. The weight of the holding tank contents is not calculated into the RV cargo carrying capacity. Traveling with full holding tank(s) could cause you to exceed the individual tire ratings and/or the RV GAWR or RV GVWR. Potential damage to suspension components, such as springs, tires and axles, could result. If you are dry camping and cannot immediately empty your holding tanks, reduce your vehicle speed until you reach a dumping station. When connected to the sewer drain line at a campground, keep the black tank drain valve closed until the holding tank is at least ¾ full. This will provide sufficient water to assist in complete draining of the black water holding tank. Repeat as needed.
Never travel with full black or grey water holding tanks. This not only wastes your fuel but depending on the location of the tank(s), it can affect your tow vehicle handling characteristics.
Never leave the black tank drain in the open position continuously when connected to the campground sewer system. Leaving the drain open will allow the liquid to drain out increasing the potential for a blockage in the tank. Keeping the drain in the closed position will prevent debris from accumulating in the tank.
Do not add automotive antifreeze or caustic chemicals, such as laundry detergents, into the holding tanks. Although these products may have a deodorizing effect, they may damage the plastic and rubber parts of the plumbing system or the components
Maintenance Record
Table of Contents
117
Section 8: Plumbing System
Before using the recreation vehicle, or after dumping the grey and black water holding tanks, always add the proper amount of deodorant to the black water tank to prevent odors and help break down holding tank contents (unless winterizing). Follow the deodorant bottle or package instructions. Driving to a disposal site will normally loosen any accumulated waste debris or solids from the sides of the holding tanks.
Black and Grey Tank Drains
There are labels on the exterior of the recreation vehicle indicating the location of the grey and black tank drains (also called dump valves). Always drain the black water holding tank first so the grey tank wastewater can help rinse any solids or debris from the dump outlet and sewer hose.
1. To make drainage easier, level the RV.
2. Remove the sewer hose housing dust cap and attach the sewer hose (customer sup-
plied).
3. Place the end of the sewer hose into the approved dump station.
4. Open the black tank dump valve (depending on your
model the valve may be located under the RV, or on
the utility center). Close the dump valve when the
black water holding tank is empty.
5. Open the grey tank dump valve (depending on your
model the valve may be located under the RV or on the utility center). Close the dump valve when the grey holding tank is empty.
Black/Grey Tank Drain and Valves
6. Remove, clean and store the sewer hose.
7. Close the sewer hose housing dust cap.
You can locate dump stations throughout the United States and Canada in Woodall's, Rand
McNally Camp Guide, Good Sam Camp Guide, KOA Kampgrounds Camp Guide and vari-
ous other publications. Some fuel stations also have dump stations.Please contact your RV
dealer for assistance in the purchase and installation of a sewer hose or sewer hose extension
(if needed).
Sewage (black) tank preparation
It is important to add enough water to prevent solid waste buildup. Follow the directions listed below and in the manufacturer's operator manual.
1. Release one to two quarts (1 or 2 liters) of water into the toilet bowl. 2. Follow the directions on your RV-approved toilet chemical bottle (customer supplied)
and put the recommended quantity of holding tank chemical into the toilet bowl. 3. Flush the toilet and allow at least two gallons (8 liters) of water to flow into the holding
tank. Waste (grey) holding tank preparation No special preparation is required, however, placing a small quantity of chemicals into this tank, such as baking soda or an approved RV chemical, will reduce odors from food particles in the system.
Cleaning and Maintenance The toilet should be cleaned regularly for maximum sanitation and operational efficiency.
118
Maintenance Record
Table of Contents
Section 8: Plumbing System
Use only RV approved chemicals. Do not use chlorine (undiluted) or caustic chemicals, such as laundry bleach or drain opening types, in the toilet system. These products damage the seals in toilets and dump valves.
Black Tank Flush (if so equipped)
The black tank flush (no fuss flush) inlet is typically located on the utility center panel (if so equipped) labeled as "Tank Flush". For models not equipped with a utility center, the inlet is located on the side of the recreation vehicle. The location may vary depending on your model. Attach a garden hose (connected to a pressurized fresh water source) to the black tank flush inlet. The water goes directly into the black water holding tank sprayer connection, allowing you to remove debris and preventing accumulation. A check valve is incorporated in the plumbing lines to prevent back flow. Flush the black water tank each time the grey and black water holding tanks are dumped or as needed.
NOTE: Utility center (if so equipped) valve positions do not affect the tank flush function. It does not matter where they are positioned when operating the tank flush.
1. Dump the black water tank (see Gray Tank Drain and Black Tank Drain) and leave the black tank drain valve open.
2. Connect a garden hose from the water supply source to the black tank flush. 3. With the water source turned ON, flush the black water holding tank until the water
running out of the black tank drain valve is clear (not discolored or cloudy). 4. Disconnect the garden hose and close the black tank drain valve. Fasten the sewer hose
housing dust cap back on the tank flush inlet.
The black tank drain valve must be OPEN any time there is a hose (water supply) connected to the black tank flush.
Do not leave any hose (water supply) connected to the black tank flush when it is not in use.
Do not use the same hose to fill your fresh (potable) water tank that is used for the black tank flush.
Tank Heaters (if so equipped)
Your recreation vehicle may be equipped with heaters for the fresh, gray, black water tanks and the water lines or drain lines. These heaters will prevent water in the tanks and lines from freezing down to -11°F (-24°C) (contingent on recreation vehicle setup).
The larger tank heaters are 120VAC and attach directly to the tanks. The thermostat controlled tank heaters will cycle on at 44°F (7°C) and off at 64°F (18°C). Water line or drain line heaters are smaller and operate on +12VDC and will be attached to the water lines or drain lines. The +12VDC heaters stay on constantly.
Maintenance Record
Table of Contents
119
Section 8: Plumbing System
All of the heaters are controlled by a single ON/OFF switch that is typically located on the command center panel or in the bathroom. The switch lights up red when ON and controls the heater circuit.
· In order for the 120VAC tank heaters to be in operation, the recreation vehicle MUST be hooked up to shore power or under generator power.
· If the recreation vehicle is not operating on shore power or generator power, only the +12VDC heaters will operate. This can result in the tanks freezing.
· The red light on the command center tank switch does not necessarily indicate that ALL heaters are operating; it is a only a warning that the heater circuit is ON.
The tank heater switch should be turned ON: When liquid is present in the holding tanks and the outside temperature approaches and maintains freezing conditions 35°F (2°C) or colder.
The tank heater switch should be turned OFF: When there is NO liquid present (tanks are empty). When dumping the black and gray holding tanks and the drain pipes. When fresh water tank and supply lines are empty or being drained for storage. When the recreation vehicle is connected to city sewer and the gate valves are open. When ambient temperatures rise and remain above freezing.
NOTE: Free draining is never recommended, especially in cold weather use.
No maintenance on the heaters is required, only a periodic inspection for loose wires, damage, etc. For additional detailed information, refer to the tank heater manufacturer's user guide.
Toilet (if so equipped)
Prior to using the sanitation system, it is strongly recommended to flush the toilet several times to release sufficient water into the holding tank. Generally, more water is required only when flushing solids.
The toilet system will perform better when water is run for ten to fifteen seconds after flushing to ensure that the waste will proceed to the bottom of the tank.
If there is not a sufficient amount of water used during flushing, the waste materials may not evacuate properly from the drain line to the tank. Clogged tanks and pipes could eventually occur. For added convenience and better sanitation system performance, it is advisable to always have four to six inches (10 - 15 cm) of water in the toilet. It is important to add enough water to prevent solid waste buildup. The following guidelines will help to prevent solid waste buildup.
120
Maintenance Record
Table of Contents
Section 8: Plumbing System
It is important to prevent solid waste buildup. Follow the toilet manufacturer's recommended instructions each time after emptying the black water holding tank.
To help prevent toilet blockage, always use RV grade single-ply toilet paper. Do not flush paper towels, diapers, sanitary napkins or other foreign objects down the toilet.
Do not use chlorine (undiluted) or caustic chemicals, such as laundry bleach or drain opening types, in the toilet system. These products damage the seals in toilets and dump valves.
Sewage (black) tank preparation 1. Release one to two quarts (1 or 2 liters) of water into the toilet bowl. 2. Follow the directions on your (approved RV) toilet chemical bottle (customer sup-
plied), by placing the recommended quantity of holding tank chemical into the toilet bowl. 3. Flush the toilet and allow at least two gallons (8 liters) of water to flow into the holding tank. Cleaning and Maintenance The toilet should be cleaned regularly for maximum sanitation and operational efficiency. For detailed information refer to the manufacturer's operator manual.
Maintenance Record
Table of Contents
121
Section 8: Plumbing System
Notes:
122
Maintenance Record
Table of Contents
Section 9: Heating & Cooling
Air Conditioner
The air conditioning system is controlled by the Firefly System. Refer to the Firefly manual for detailed information on air conditioner temperature control.
Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner. This also will lead to a loss of air volume, possible equipment damage and an expensive cleaning process.
Roof Mount (if so equipped) A special foam gasket is placed between the roof material and the sub frame of the air conditioner to guard against water leakage. The air conditioner is subjected to wind pressures along with motor vibration during normal operation. Inspect the mounting bolts for tightness to ensure there is no leakage or looseness at least annually. Re-tighten bolts when they are loose. DO NOT over tighten these bolts as it may damage this gasket. The air conditioner gasket is a wearable part that eventually will need to be replaced. To gain access to the bolts, remove the filtered panel cover on central air systems or the entire air box on non-central air conditioners.
Wall Mount (if so equipped) Keep the air inlet grill and cabinet clean by wiping with a cloth dampened with warm water and a mild detergent.
Heat Pump Operation (if so equipped) Set the thermostat for either electric or gas heat. On the electric setting, the heat pump will become the primary heat source as long as the interior temperature of the RV has not dropped 5° below the thermostat set point. If this occurs, the thermostat will automatically activate your gas furnace.
The furnace will continue as the heat source until the thermostat set point has been satisfied. At that point, the heat pump will again become the primary heat source.
For RV models with a touch screen system, the heating cooling controls are included on the touch screen selectable screens.
For additional information refer to the manufacturer's owner's manual included in your warranty packet or consult your dealer.
Power Roof Vent (if so equipped)
The 12-volt DC attic fan (or powered roof vent) allows fresh air to circulate through the recreational vehicle. Do not leave the attic fan open when the recreational vehicle is stored or unattended for long periods.
High winds, other unusual conditions or obstructions may prevent the dome from closing; the resulting leakage could cause non-warrantable damage.
To use your fan most effectively, close all vents and slightly open a window on a shaded side of your recreation vehicle. You are directing the air flow by opening a window. For additional safety and operating information refer to the manufacturer's owner's manual.
Control pad (if so equipped) The attic fan may be controlled by a control pad. The dome can be raised or lowered with the UP/DOWN buttons, and the speed of the fan is controlled by the ARROW buttons. It is also equipped with a rain sensor that will close the vent automatically when it rains. The rain sensor can be turned on/off by holding the DOWN button for 3 seconds.
Maintenance Record
Table of Contents
123
Section 9: Heating & Cooling
NOTE: For RV models with touch screens, the powered roof vent(s) may be controlled on one of the selectable screens on the touch screen.
Furnace
The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level.
The furnace requires both 12-volt power and propane gas for full operation. Make sure you have sufficient power available before operating your furnace.
If you have any questions contact your dealer or Customer Service. A qualified RV technician should perform all furnace maintenance at least once a year (more often depending on furnace usage). Never attempt to repair the furnace yourself.
Ducting and Return Air All heat discharges, registers and return air grills must be free and clear of obstructions. This includes all closeable registers that are intended to reduce airflow, do not shut it off completely.
The furnace should be inspected periodically (monthly during the heating season) for presence of soot on the vent. Soot is formed whenever combustion is incomplete. This is a visual warning that the furnace is operating in an unsafe manner. If soot is observed on the vent, immediately shut the furnace OFF and contact a qualified service agency. Operating the furnace under this condition could lead to serious property damage, personal injury or loss of life.
To ensure your personal safety, do not obstruct or alter the furnace in any manner. Do not install screens over the vent for any reason. Screens will become restricted and cause unsafe furnace operation. For your safety, only the manufacturer's factory authorized parts should be used on your furnace.
NOTE: For RV models with touch screens, the furnace controls may be included on the selectable menu screens of the touch screen.
Fireplace (if so equipped)
Your recreational vehicle may include an electric fireplace insert. For detailed operating and safety information, refer to the manufacturer's user guide included in your warranty packet.
124
Maintenance Record
Table of Contents
Microwave
Section 10: Appliances
To prevent damage, remove the turntable from the microwave when traveling.
Make sure you are connected to a 120-volt power source.
Never use the microwave cavity for storage. The microwave cavity should always be empty when not in use.
For details on operation, cleaning and safety information, refer to the manufacturer's user guide.
General Cleaning Microwave and Convection Microwave IMPORTANT: Before cleaning, make sure all controls are off and the microwave oven is cool. Always follow label instructions on cleaning products.
To avoid damage to the microwave oven caused by arcing due to soil buildup keep cavity, microwave inlet cover, cooking rack supports, and area where the door touches the frame clean.
Clean with mild soap, water and a soft cloth or sponge, or as indicated below. Grease filters: mild soap and water or dishwasher. Door and exterior: mild soap and water, or glass cleaner applied to paper towel. Control panel: sponge or soft cloth and water. Stainless steel (on some models): mild soap and water, then rinse with clean water and dry with soft cloth, or use stainless steel cleaner. Turntable: mild soap and water or dishwasher. Rack(s): mild soap, water and washcloth. Dishwasher cleaning is not recommended.
Convection Microwave (if so equipped) The convection microwave bridges the gap between microwaving your food and conventional cooking. Make sure there is sufficient 120-volt power before operating the convection microwave (see Calculating Electrical Load). For details on operation and safety information, refer to the manufacturer's user guide.
Cooking Safety
In Case Of a Grease Fire
Do not attempt to use water to put out the fire. Water can spread some types of fire, and electrocution is possible with an electrical fire.
Grease is flammable. Never allow grease to collect around top burners or on the cook top surface. Wipe up spills immediately. Refer to Section 2 Safety Precautions, for fire safety and fire extinguisher information.
Maintenance Record
Table of Contents
125
Section 10: Appliances
Cooking With Propane (if so equipped) See the Propane System section for important safety instructions. Refer to the manufacturer's owner's manual for detailed operating and safety instructions for all propane appliances.
Cooktops, Range and Oven (if so equipped)
For detailed operating and safety information, refer to the manufacturer's user guide.
During and after use, do not touch or let clothing or other flammable material come in contact with the top burners or heating elements, burner grates or areas near the top burners or oven until they have had sufficient time to cool. These areas can get hot enough to cause burns.
Never leave cooking food unattended. Turn pan handles inward, but not over the tops of the other range burners. Ensure that pans used are large enough to contain the food and avoid boil-overs. Heavy splattering or spills left on the cooktop can ignite and cause burns.
If using glass, glass/ceramic, ceramic, earthenware or other glazed utensils or cookware verify it is safe for use on the top burners.
Do not cover the oven vent openings while the oven is in operation. Restricting the flow of combustion air will create an asphyxiation hazard.
Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia. Always allow the cooktop to cool before cleaning.
Cleaning instructions Refer to the manufacturer's user guide included for detailed cleaning instructions. General Cleaning
To avoid damage and possible burns, be sure the appliance is off and all parts are cool before handling or cleaning.
Use care to avoid steam burns if a wet sponge or cloth is used to wipe spills on a hot surface.
Some cleaners can produce noxious fumes if applied to a hot surface. To prevent staining or discoloration, clean appliance after each use. If a part is removed, be sure it is correctly replaced. If a spillover occurs while cooking, immediately clean the spill from the cooking
area while it is hot to prevent a tough cleaning chore later. Using extreme care, wipe spill with a clean, dry towel. Electric Drop-In Cooktops (if so equipped)
Do not use aluminum foil under any circumstances on the electric range cooktop, as this material will damage the cooktop surface if it melts.
126
Maintenance Record
Table of Contents
Section 10: Appliances
NOTE: Make sure you are connected to a 120-volt power source.
Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop. The 2 burner match-light cooktop has two 6500 BTU/H burners with control panel. The 3-burner piezo-igniter cooktop has (1) front 9000 BTU/H burner and two rear 5200 BTU/H burners. The 3 burner cooktop is also equipped with a control panel. Refer to manufacturer's user guide for detailed operating and cleaning information. Kitchen Range and Oven (if so equipped)
NOTE: To help reduce potential condensation or unwanted cooking odors, turn on the overhead kitchen roof vent or the range hood vent (if so equipped).
To prevent damage, always use the manufacturer's recommended size flat bottom pan(s). Generally, the pan should be large enough to cover the burner, but not be more than one inch larger than the burner grate. Do not use a broiler pan, griddle or any other large utensil that covers more than one burner at a time. This will create excessive heat that may cause melting, sooting or discoloration. The use of undersized pans could expose a portion of the heating element to direct contact and may result in ignition of clothing. Proper relationship of pans to burner will improve efficiency. Oven (if so equipped) The propane gas oven must have 12-volt power to operate. Do not use the oven as a storage area. If you have any questions, contact your dealer or our customer service department.
Range Hood (if so equipped)
Whenever the stove in the RV is being used, the range hood MUST be turned on, and the inner flap MUST be unsnapped and free to move. Failure to do so can create an asphyxiation hazard by restricting air flow to this vent.
If your recreational vehicle is equipped with a range hood, it will be connected to an exterior vent.
The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep insects, debris, snow, rain, etc. from entering the recreational vehicle.
Anytime the stove inside the recreational vehicle is being used, this flap MUST be unsnapped and the range hood turned ON to vent fumes outside the vehicle.
Maintenance Record
Table of Contents
127
Section 10: Appliances
Refrigerator
The refrigerator is not intended for quick freezing or cooling. We recommend stocking it with pre-frozen or pre-cooled food when possible. The shelves should not be covered with paper or plastic and the food items should be arranged so air can circulate freely. Keep the area at the back of the refrigerator clean and free of debris. Check for obstructions in the exterior refrigerator vent area (i.e., spider webs, bird nests, etc.). Use a soft cloth to dust off the debris. For optimum efficiency and performance, it is recommended the refrigerator be checked at least twice a year as part of the routine maintenance. For detailed operating and safety information, refer to the manufacturer's user guide. Gas/Electric Models (if so equipped)
If you smell propane gas STOP! Follow the directions located in your manufacturer's owner's manual and in this manual.
Residential Models (if so equipped)
NOTE: If you are using electric to power the refrigerator, make sure you are connected to a 120-volt power source.
The ice maker should be turned off and the ice tray emptied when power to your motor home has been shut off. With no power, the ice will melt and water will "pool" in the refrigerator door. When power is restored, the vibration will cause this water to run out of the door and on to the motor home floor.
3-Way Refrigerators (if so equipped) Depending on your model, you may have a 3-way refrigerator (12VDC, LP GAS or 120VAC).
Converter output (12VDC) is not intended for normal operation of the 3-way refrigerator. When the motor home is parked and the power cord is plugged in, set the 3-way refrigerator to "AC power". The "DC mode" is to be used only when traveling and will pull power from the auxiliary battery charge line (if so equipped). When camping without available AC power, utilize the propane mode.
Cleaning Your Refrigerator The following are general cleaning guidelines. For detailed information on cleaning your specific refrigerator, refer to the manufacturer's user guide.
128
Maintenance Record
Table of Contents
Section 10: Appliances
Cleaning the Interior 1. Unplug refrigerator or disconnect power. 2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a
clean sponge or soft cloth and a mild detergent in warm water. 3. Inside the refrigerator, use a warm water and baking soda solution consisting of ap-
proximately 1-tablespoon (15ml) baking soda to 1 quart (1 liter) of water. This solution cleans and neutralizes odors. Rinse and wipe dry. 4. Leave an open box of baking soda in the refrigerator and freezer to help prevent odors.
NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.
There is no need for routine condenser cleaning in normal operating environments. If the environment is particularly greasy or dusty, or if there is significant pet traffic, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.
If you need to clean the condenser:
· Remove the base grille.
· Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.
· Replace the base grille when finished.
Cleaning the Exterior Painted metal exteriors: wash with a clean sponge or soft cloth and a mild detergent in warm water.
Stainless steel exteriors: wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use appliance wax, polish, bleach, or other products containing chlorine on stainless steel. Stainless steel can be cleaned with a commercially available stainless steel cleaner. A spray-on stainless steel cleaner works best.
IMPORTANT: Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.
For silver-accented plastic parts, wash with soap or other mild detergents. Wipe clean with a sponge or damp cloth. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach as these products can scratch and weaken the paint finish.Replace the base grille when finished.
Washer/Dryer (if so equipped)
If your motor home is equipped with a stackable washer/dryer set, make sure you have sufficient power available before operating the washer or dryer (refer to calculating electrical load). Make sure you are connected to a 120-volt power source.
Refer to the manufacturer owner's manual included in your Owner's Portfolio for detailed safety, operating and care instructions.
Maintenance Record
Table of Contents
129
Section 10: Appliances
A dryer vent opening must be cut into the sidewall of the RV if installing a dryer. Look for the dryer vent label on the wall in the location where the dryer will be installed. Instructions on how to cut the dryer vent hole and install the vent in the wall of the RV are included in your documentation packet.
Contact your Dealer or Customer Service for details on sanitizing and winterizing.
Dryer Vent Label
Gas dryers should NEVER be installed in your recreation vehicle. Dryer prep has been designed for electric dryer operation ONLY.
Never place items in the washer that are dampened with gasoline or other flammable fluids. No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire
Do not operate a dryer in the recreation vehicle unless the dryer is properly vented.
Water Heater See Plumbing Section
130
Maintenance Record
Table of Contents
Section 11: Electronics
HDTV Antenna/Satellite System
Your recreation vehicle may be equipped with an exterior amplified high definition TV antenna. The antenna comes equipped with a signal meter and a power injector to aid in receiving the strongest possible signal when tuning in HDTV stations. Antenna Positioning: The knob on the base inside the RV is used to rotate the outdoor roof antenna. The arrow on the knob should be pointed towards the TV signal source (TV station). Press the button on the side of the knob and turn it to rotate the antenna for optimum signal. The antenna will rotate a full 360°.
NOTE:This antenna is a fixed height (12") and cannot be lowered or raised. Trees and foliage will interfere with receiving a strong HDTV signal.
Power Injector (if so equipped) The power injector button located on the wall plate, switches between your cable/satellite signal and the over-the-air (OTA) HDTV signals. When the button on the wall plate is turned ON, it lights green and interrupts the satellite/cable input to the TV. It allows the OTA HDTV signals from the outside roof antenna to your TV. When the button is turned OFF, satellite/ cable signals are resumed on your TV. Signal Strength Meter (if so equipped) The base may have a built in signal strength meter to aid in obtaining maximum TV signal. A row of LED lights will light up on the face of the base enclosure to indicate signal strength. Optimum signal is indicated when the maximum number of LEDs are lit. · Make sure the power injector is turned ON at the wall plate which turns power on to
the antenna.
· To turn on the signal meter, slide the black button on the side of the base (arrow in photo).
· Rotate the small attenuator knob on the face of the base enclosure clockwise.
· Press the button on the side of the large knob with the arrow, and rotate it until the maximum number of LEDs light.
· Rotate the small attenuator knob counter-clockwise until the last illuminated LED light flickers.
· Rotate the large antenna knob to illuminate the last flickering LED light. · Refer to your TV (or converter box) manual for information on scanning for available
OTA channels.
Maintenance Record
Table of Contents
131
Section 11: Electronics
Antenna Power Supply (if so equipped) For good station reception, the antenna power supply must be turned ON to
view local television stations. Turning the antenna power supply ON sends
12-volt DC through the cable to the TV roof antenna. The voltage energizes the transistors in the antenna head amplifier. The TV signal then comes down the cable to the outlets.
Turn the antenna power supply OFF to view cable television or to use a
VCR or DVD. The ON/OFF switch is located on the wall plate for the antenna connection. Satellite (if so equipped)
Antenna Power Supply
Please refer to the manufacturer's instructions for setup, care and maintenance.
Exterior Entertainment Center (if so equipped)
The exterior entertainment center is located on the curbside of the unit. You can access the entertainment center by opening the exterior cargo door to the stationary open position.
Refer to the individual component manufacturer's information for detailed operating instructions.
132
Maintenance Record
Table of Contents
Section 12: Interior
Cleaning The Interior
To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer's information for the recommended cleaning agent. If in doubt, check to see if the cleaner will cause damage by testing a small area out of sight or contact your dealer for assistance. Do not use flammable liquids or sprays to clean the recreation vehicle.
Décor Glass (if so equipped) Use a glass cleaner to remove smudges, smears and spots. If there is decorative etching on the décor glass, use care when cleaning around that area.
Furniture Upholstery Vacuum the furniture upholstery regularly using a soft brush attachment to remove any loose dirt or debris.
Fabric (if so equipped) It is recommended the fabric be professionally cleaned if it becomes stained or soiled. The professional cleaner should be made aware the fabrics that may have been treated to be fire resistant. For more information, refer to the specific furniture manufacturer's care instructions.
UltraleatherTM (if so equipped): It is recommended the UltraleatherTM be professionally cleaned if it becomes stained or soiled. For more information, refer to the specific furniture manufacturer's care instructions.
Leather (if so equipped): Periodic vacuuming, using a dry cloth to wipe up spills immediately, and using a damp cloth on problem areas, will help to keep your leather furniture in good condition. Leather surfaces can vary, as do the cleaning methods. Refer to the furniture manufacturer's recommendation, or consult a cleaning professional.
It is recommended you do not use any cleaners containing oils, waxes or silicones. Cleaners containing silicone can eventually destroy the finish on the leather. Cleaners containing oils or waxes should not be used as they leave residues on the surface of the leather, which can attract more dirt and eventually lead to cracking.
Window Treatments Fabric Drapes and Valances: Dust occasionally with a vacuum and soft brush attachment. It is recommended the fabric be professionally cleaned if it becomes stained or soiled. The professional cleaner should be made aware the fabrics that may have been treated to be fire resistant.
Window Shades Shades should be vacuumed periodically to remove dust. Using your vacuum cleaner's upholstery brush on low suction will remove most dust and dirt from the shade. Refer to the shade manufacturer's owner's manual for additional and detailed information.
To remove stuck on dust or stains refer to the following guide.
Solar Shields: Use a sponge or soft brush and water to remove stains. A mild cleaning solution can be used to remove tougher stains. Rinse after cleaning by wetting a clean cloth in fresh water, wringing our any excess and wiping the areas where the cleaner was used.
Day/Night Shades: Clean with a mild cleaning solution using a sponge or paper towel. Wipe down with water after cleaning and dry thoroughly before raising the shade. Do not use spot remover, household cleaners or detergents to remove soiled spots, as these may cause damage to fabric or loss of color from fading.
Mini Blinds: A simple dry rag may do the trick. If they are especially dirty, you can use cold or warm water to clean them; never use hot water.
Maintenance Record
Table of Contents
133
Section 12: Interior
Fill a spray bottle with water and a tiny amount of soap. Then spray a lint-free towel with the mixture and use the towel to wipe down each slat. While cleaning, try not to bend the slats. They can also be soaked in a bathtub to loosen up any debris so the slats can be wiped down easily. Roller Shades: Clean by using soapy water or a mild cleaning solution on spots. Try a small area first because harsh household cleaners or detergents may cause damage to fabric or loss of color. It is recommended to dust the rails and fabrics of the shades on a regular basis. Shades should be kept in the closed or up position when not in use to maintain pleat retention and minimize dirt and soil build-up.
NOTE: If your recreation vehicle must be stored for an extended period of time, store shades in the up position and cover your windows with additional protection (I.E. Cut out cardboard).
Cabinetry and Tables To keep hardwood doors, cabinet fronts and hardwood tables looking like new regularly dust with a soft cloth dampened with a cleaning polish or mild detergent solution. Avoid using ammonia based products or silicone oils as they may cause damage if used over a long period of time. The finish is durable and resistant to most household spills. However, spills should be wiped up promptly to avoid potential problems. Excessive prolonged exposure to direct sunlight, high temperatures and high humidity can cause damage to both the finish and the wood itself. Interior Wall Panel To clean, use a mild solution of soap and lukewarm water with a soft sponge or cloth. Wipe dry with a soft, clean cloth.
Do not use abrasive cleaners as they may cause the vinyl to scratch and become dull. Do not use cleaners that contain bleach
Putty sticks can be used to cover scratches on the wood surface wall panels. These can be obtained from local hardwood stores and lumberyards. Contact your dealership service department for assistance in repairing décor paneling. Quik Panel Wall Panels (if so equipped) Quik Panels are used on certain Entegra motorhome models and may be treated and cleaned as a high quality painted surface. All Quik Panels are sealed or glazed and can be cleaned with a soft cloth and mild soap and water (such as dish soap). Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic. Avoid using "citrus" or biodegradable cleaners that contain "D-Limonene" as they may damage plastic materials.
134
Maintenance Record
Table of Contents
Section 12: Interior
NOTE: Oil based soaps and cleaners are not recommended. No abrasive cleaners or alcohol cleansers should be used. If other cleaner solutions are used, first try on a spot in an inconspicuous area.
Sofa and Dinette
Always use seatbelts if sitting in the sofa or dinette while the motor home is in transit
Your motor home may be equipped with one of the following sofa styles. Hide-A-Bed Sofa or Sofa Sleeper To make the hide-a-bed sofa into a bed, remove the seat cushions and pull the sofa back towards you firmly and gently. Activate (or deflate) the air mattress (if so equipped) using the supplied furniture manufacturer's instructions. To convert the hide-a-bed back into the upright sofa position, reverse the process. Jack Knife Sofa The jack knife sofa functions much the same as a residential futon. To make the sofa into a bed, lift up on the bottom seat cushion and pull it towards you. The sofa back will drop down to provide a sleeping surface. For additional comfort and to reduce fabric damage, you may want to place a cover or air mattress (customer supplied) over the sofa when it is in the sleeping position. Trifold Sofa The trifold sofa offers very similar features to a traditional hide-a-bed. The following illustrations detail converting the sofa into a bed. 1. Remove the tri-fold sofa pillows and set aside. 2. Using the strap handle, pull the sleeping surface up, then out. 3. While sleeping surface is up, fold out legs. Extend the sleeping surface until grounded. 4. Once sleeping surface is grounded, fold head board down flat.
Maintenance Record
Table of Contents
135
Section 12: Interior
Booth Dinette (if so equipped) The dinette is designed to seat up to four adults. Depending on your model, there may be a storage area in the dinette bench. To access this storage, remove all the cushions and lift up on the bottom seat support. If the bottom seat support is secured closed with screws, do not remove the seat support or use this area for storage. The dinette seats that are secured with screws contain factory installed equipment and should only be accessed by a qualified service technician. Your motor home may be equipped with one of the following dinette styles that can be converted into a bed. Booth Dinette Remove all the cushions from the booth dinette. Lift up the tabletop and remove the detachable table legs. Place the tabletop on the ledges provided between the booth dinette benches. Lay the seat back cushions against the back of the dinette bench. Lay the dinette seat bottom cushions in between the seat back cushions. The area where the cushions meet should be slightly raised. Push the raised cushion ends down gently as the cushions are designed to fit snugly. Reverse this process when converting back to the booth dinette. Dream Dinette Remove all the cushions from the dinette. Locate the locking mechanism rod under the table top. This locking mechanism is designed to keep the table from collapsing into the bed configuration. Turn this rod so it moves out of the channel and points down toward the floor. Push the dinette table down toward the floor to form the platform for the bed. Arrange the cushions to form a mattress for sleeping. To convert back to a dinette, remove the cushions, pull the table back up as high as it will go, and turn the rod underneath back to the locked position.
Make certain the rod underneath the table is in the locked position before using then the table in the dinette position. Failure to secure the table in the locked position may result in injury or property damage.
Dream Dinette Unlocked
Dream Dinette Locked
Free Standing Dinette Chairs (if so equipped) Two free standing chairs and two folding chairs are included in the free standing table/chair package. When traveling in the motor home, it is recommended the free standing chairs be fastened securely at the dinette table, and the folding chairs be secured in a closet or storage area.
136
Maintenance Record
Table of Contents
Section 12: Interior
Do not allow occupants to occupy the free standing dinette chairs while the motor home is in transit.
Pantry or Hutch (if so equipped)
Your recreation vehicle may have a pantry or hutch that you can use for storage. Make sure all items stored in the pantry or hutch are secured to prevent shifting during travel. This cabinetry has been designed to accommodate the normal camping items which may be bulky but not necessarily heavy. Remember your recreation vehicle's load capacity is designed by weight, not volume, so you cannot necessarily use all available space. If your pantry or hutch has sliding pantry shelves, they have been equipped with a locking mechanism to keep them in place during transit. To secure the shelf in place, push it all of the way in until the latch tab clicks into place. Always pull out slightly on the shelf to make sure that it is stationary and secure in the transit position. To release the shelf, push in on the tab and pull the shelf slowly towards you.
Your RV's load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading the vehicle. Do not exceed your GVWR and ensure you are loading the vehicle as evenly as you can for the best possible handling. Ensure heavy items are secured so they do not shift during travel.
Countertops
To prevent permanent damage Always use hot pads or trivets under hot pans, dishes, or heat producing appliances. Heat will damage the solid surface countertops. Use a cutting board to prevent unnecessary damage to the countertops. Do not cut directly on the solid surface countertop. Avoid harsh chemicals such as drain cleaners, oven cleaners, etc. Do not let cleaners with bleach set on the top. Wipe them off promptly. Run cold water when pouring hot/boiling water into the sink. Use coasters under all glasses, bottles and cans. Do not store toiletry products directly on your countertop surface. Hair products, perfumes, colognes, nail products, creams, lotions and potions have a tendency to spill or leak and go overlooked. Even though the counter top is sealed, a substance that remains on the surface for an extended period may stain Quartz.
For additional information on the removal of difficult stains or surface damage repair, refer to the countertop manufacturer's user guide.
Laminate Countertops (if so equipped) Glass rings, food spills, water spots and smudges usually wipe off with a damp sponge. Stubborn stains can be removed with a general-purpose spray cleaner. Some stains can be removed by squeezing fresh lemon juice over the stain and allowing the juice to soak for approximately forty-five minutes. After 45 minutes, sprinkle baking soda over the lemon juice and rub with a soft cloth.
Maintenance Record
Table of Contents
137
Section 12: Interior
Solid Surface Countertops (if so equipped) Soapy water, ammonia based cleaners (not window cleaners as they can leave a waxy build up that may dull the surface) or commercially available solid surface cleaners will remove most dirt and residue from all types of finishes. A damp cloth followed by a dry towel will remove watermarks. Difficult stains can be removed from the matte finish with a green Scotch Brite® pad and a mild abrasive cleaner. Disinfect the surface periodically with diluted household bleach (one part water to one part bleach). For cuts and scratches, sand the matte finish lightly with (220) fine grit sandpaper until the cut or scratch is gone. Restore finish with a green Scotch Brite® pad and mild abrasive cleaner.
Solid surface sink maintenance Occasionally, clean the solid surface sink by filling one-quarter full with a 50/50 water/ bleach solution. Let soak for 15 minutes, and then wash sides and bottom of sink as solution drains. Quartz Countertops (if so equipped)
Quartz will absorb heat from the pan. Resin in the countertop can withstand temperatures of 150°. Do not place a hot pan (from stove or oven) on a quartz countertop as it will burn or cause permanent damage. Heat will damage the solid surface countertops.
Quartz is highly scratch resistant and stain resistant but prolonged exposure to sunlight can eventually damage a Quartz countertop.
NOTE: Only have a professional fabricator repair any countertop damage.
Cleaning your countertop To keep quartz countertops clean, wipe up spills immediately before they have a chance to dry. Use mild dishwashing soap and a soft cloth. For dried spills a non-abrasive sponge (designed for nonstick pans) works well along with a little elbow grease. Keep a plastic putty knife handy for scraping off gum, nail polish, paint or other messes. Remove cooking grease using a degreasing product that will loosen then remove the grease. Follow cleanser manufacturer instructions. For stains like permanent markers moisten a cloth with Goo Gone (or similar) and rub into the stain. Rinse with warm water. A general deep cleaning is recommended at regular intervals using a nonabrasive surface cleaner on the countertop. Let it sit for 10 minutes and wipe with a non-abrasive sponge.
Never use abrasive cleansers and avoid scouring pads. If you need a gentle cleanser to remove stains make sure it is specifically designed for Quartz.
Do not use nail polish remover, turpentine, drain cleaner and dishwashing rinsing agents. You may use diluted bleach or a mild bleach cleanser, but oven cleaners or concentrated bleach should never be used. If they come in contact with the counter top, rinse immediately with water.
Flooring
Carpet Vacuum your carpet regularly. It is important to remove loose soil and debris while it is on the surface. Heavily traveled areas (i.e., walkways, areas in front of the furniture) may be protected with small throw rugs to prolong the life of the carpet.
138
Maintenance Record
Table of Contents
Section 12: Interior
Prompt attention to spots and spills is essential. Remove as much of the spill as possible. Absorb wet spills as quickly as possible by blotting repeatedly with white paper or cloth towels.
Refer to the manufacturer's guide for detailed cleaning information, or contact a cleaning professional. Vinyl Flooring (if so equipped) Periodically vacuum or sweep to remove dirt and gritty particles. Although most common spills will not permanently stain the vinyl floors, they are usually easier to remove if wiped up before they set. Blot with a paper towel and wipe clean with a damp cloth. Do not use dish detergents or vinegar and water because they will dull your floor. To care for the vinyl floor covering, use a damp mop with water and a mild cleaner on the entire floor. DO NOT SOAK THE FLOORING. Use care to avoid wetting the carpet edges. To avoid problems of "yellowing" linoleum, the flooring manufacturer recommends avoiding cleaners that contain oil based solvents (i.e. lemon oil, Murphy's Oil Soap, etc.). Ceramic Tile (if so equipped) Vacuum the ceramic floor tiles regularly to remove dirt and other gritty particles, then damp mop or sponge with an all-purpose, non-oil based cleaner. Heavily trafficked tile may require more intensive cleaning. Refer to the manufacturers guide or contact a cleaning professional for detailed cleaning information. Grout, the material used between the tiles is porous, and sealing it will simplify maintenance in the future. The ceramic tile manufacturer recommends applying a sealer at least twice a year for maximum stain protection. Sealers may be purchased at most local home centers or floor-covering stores. DO NOT:
Use cleansers containing acid or bleach for routine maintenance. Use wax cleaners, oil-based detergents or sealants to maintain your tile (sealants
may be used on grout joints and natural stone). Use ammonia (it will discolor grout). Use harsh cleaning aids like steel wool pads or scouring pads containing metal. Use a cleaning agent that contains color on unglazed ceramic tile or natural stone. DO: Test scouring powders on a small area first (not recommended for natural stone). Use a sealer on grout joints. Have any damaged or broken tiles replaced only by a qualified contractor.
Ceiling Fabric
The ceiling fabric is made from padded vinyl fabric. Wash with mild detergent and water. Use a soft bristle brush for stubborn soil. Rinse and dry. Some household cleaners and solvents remove plasticizers from vinyl, making them brittle. Abrasive cleaners may mar or scratch the surface. Always test a small hidden area before applying cleaners to the vinyl surface.
Privacy Drape Installation
1. Starting on the driver's side, attach the black plastic hook to the loop on the wall (behind the driver's seat). Make sure the Velcro® on the drape is facing the motorhome windshield.
2. Pull the drape towards the windshield and past the driver's side sun visor. Open the sun visor against the windshield to hold the drape in place.
Maintenance Record
Table of Contents
139
Section 12: Interior
3. Continue across the windshield to the passenger side, again opening the sun visor and placing the drape behind it.
4. Attach the black plastic hook on the passenger side of the drape, to the loop on the wall behind the passenger's seat.
5. Attach the Velcro® at the top edge of the drape to the corresponding Velcro® on the cab area roof (above the driver's and passenger's doors).
6. Attach the Velcro® at the bottom corners of the drape to the corresponding Velcro® on the wall.
Bed Storage
Additional storage has been provided under the bed. To access the storage area, grasp the ledge at the foot of the bed and lift carefully. The bed platform must be held when raised. It is recommended that two people retrieve stored items from under the bed so that one person may hold the platform, and the other to retrieve the stored items from under the bed. Lower the platform slowly to close it. DO NOT DROP THE PLATFORM.
Before lifting, be sure there is nothing on the bed that will restrict its movement or add extra weight.
Use caution when opening or closing the bed to keep hands and fingers at the end ledge provided (not on the side or farther back than necessary).
Exercise extreme caution when opening the bed storage platform. Platform must be held open (unless equipped with a prop rod or gas struts) and slowly lowered until closed.
The bedroom electric slide room system may be located under the bed. Use care not to obstruct the slide room system when using the under bed storage.
Failure to comply with these guidelines can result in serious injury or property damage.
Certain models may be equipped with a prop rod or gas struts to assist with easy access to under bed storage. Prop Rod (if so equipped) If your model is equipped with a prop rod:
With the help of a second person, raise the bed platform. Release the prop rod from its holder. Put the end of the rod in the bracket under the bed platform. To lower the platform, release the prop rod from the bracket under the bed plat-
form, re-attach the prop rod to the holder on the bed base, Lower the platform slowly until closed.
140
Maintenance Record
Table of Contents
Section 12: Interior
Gas Struts (if so equipped) On certain models, the bed platform may be equipped with gas struts to assist with easy access to storage area.
Grasp the ledge at the foot of the bed and lift carefully. Two gas struts will hold the bed platform open allowing access to the storage area. To close, carefully push down on the bed, slowly easing it to the closed position.
Cab-Over Power Bunk Bed (if so equipped)
Your motor home may be equipped with an over-the-cab power bunk bed. The storage position for the bunk is near the ceiling. Any time the bunk is raised into the storage position, the seat belt style interlock (Fig 1) located at the left end of the bunk, must be latched. The interlock belt, when latched, disables the key switch, and the bunk cannot be lowered/raised even if the key switch is ON.
The bunk bed may include a steel ladder that hooks on to the side of the bed in order to access the sleeping area. Do not exceed the weight limit of the bunk ladder (see Warning information below).
There should be no people, pets or objects on or below the bunk while raising or lowering it. Failure to comply may result in serious injury or property damage.
With vehicle in transit, the bunk should always be in the raised storage position with the interlock belt latched. Never ride on the bunk while the vehicle is in motion. Never store the bunk ladder or any other objects on the bunk when it is raised in the storage position and vehicle is in motion. Failure to follow these instructions may result in injury or property damage.
Capacity of the Cab-Over bunk is 750 lbs maximum. Exceeding this weight limit may result in injury or property damage.
Lowering the bunk: To lower the cab-over bunk, unlatch the interlock belt (Fig 1) (it operates just like a seat belt), insert the key into the key switch (on the left end of the bunk) (Fig 2), and turn it to the right to the ON position (Fig 3). Lower the bunk by pressing and holding the yellow down arrow under the picture of the bed on the key switch label. The bunk automatically stops when it is fully lowered. Return the key to the OFF position.
Maintenance Record
Table of Contents
141
Section 12: Interior
Raising the bunk: To raise the cab-over bunk, turn the key switch to the right to the ON position, and then press the yellow up arrow above the picture of the bed on the key switch label. The bed will begin rising. When fully raised, return the key to the OFF position, and latch the interlock belt (Fig 1). The black rocker switch (Fig 2) operates the ceiling light above the bunk.
NOTE: If the ceiling light is left on when raising the bunk, it will automatically turn off as the bed rises regardless of the rocker switch position.
Bunk Beds and Bunk Ladders (if so equipped)
Your recreational vehicle may be equipped with bunk style beds. Bunk bed weight ratings may vary depending on your model and the style of bunk bed. Weight capacities are listed on the bunk capacity label. Do not exceed the bunk weight capacity. Bunk Ladders (if so equipped) Your recreational vehicle may be equipped with a ladder to access the upper bunk. This ladder may be a separate steel ladder, or a wooden ladder attached to the bunk beds.
The top of the ladder is secured to the ladder storage compartment. To operate the ladder, lift up and out of the storage tray. Pivot the bottom of the ladder out. Be sure the ladder is securely in place on the floor before climbing to the upper bunk.
When storing the wood ladder, place the bottom of the ladder back into the tray in the storage compartment. This keeps it secure during transport and clear of walkways.The steel ladder (if equipped) will simply hook onto the upper bunk.
142
Maintenance Record
Table of Contents
Section 12: Interior
NOTE: Some types of bunk beds do not include a ladder.
Exercise extreme care when entering or exiting the bunk beds and using the ladder.
Do not allow more than one person on the top bunk. Do not allow children under 6 years of age to use the upper bunk. Do not allow horseplay on or under the bed and prohibit jumping on the
bed. Make sure the ladder is anchored properly to the bed. Never allow more than one person on the ladder at a time. Children should always be supervised when using the ladder or when
entering or exiting the bunk beds. Weight limit of the bunk ladder is 300 lbs. (136 kg). Never exceed this
weight. Maximum weight limits for bunk beds will vary depending on model or
bunk style. Never exceed the maximum weight specified on the bunk capacity label. Failure to follow these instructions can result in serious bodily injury.
Maintenance Record
Table of Contents
143
Section 12: Interior
Notes:
144
Maintenance Record
Table of Contents
Section 13: Exterior
Cleaning The Exterior
To protect your recreation vehicle's exterior finish, wash it often and thoroughly. You may wash and wax your new recreation vehicle 60 days after purchase. The exterior paint needs time to cure before any wax is applied to the exterior surface. Careful maintenance for the first 60 days will assure a long lasting durable finish.
Your RV is exposed to many environmental conditions that have an adverse affect on the paint finish:
Road Salt and Sodium Chloride Road Tar / Bugs Bird Droppings / Tree Sap Industrial Fallout / Acid Rain/Pollution UV Exposure and Moisture The most common problems resulting from these conditions are corrosion, staining, and chemical spotting. Generally, the longer the foreign material remains in contact with the exterior finish the more extensive the damage. These problems can be minimized by regularly scheduled washing and polishing. Wash your recreation vehicle as soon as possible if it becomes contaminated with foreign material.
Avoid parking under trees or near ocean sea salt. Ice or snow should be brushed off, not scraped, from the painted surface. Avoid gravel roads.
Anti-freeze, gasoline or washer solvents if spilled on the painted surface should be rinsed off with water immediately. Bugs and bird droppings should be rinsed off daily.
Washing Commercial washing should be avoided. Wash with cold water using a mild liquid soap. Dry wiping with a dry cloth is not recommended.
Make sure the RV's surface temperature is cool, under 90 F, and out of direct sunlight. A shaded area is ideal for washing your vehicle as direct sunlight causes water spotting. Use a mild soap, detergent or car wash shampoo. Try to avoid combination wash-n-wax products as these waxes can cause build up and are designed for smaller surfaces. Have two dedicated sponges or wash mitts: one for the paint finish and one for the wheels and under carriage. Brushes or wash mitts made of plastic bristles are acceptable for use on tires and wheel wells, but are not intended for use on the paint finish. Avoid using such items on painted surfaces as they will damage the finish. Wash the wheels and wheel wells first as this removes heavy dirt and debris and prevents it from splattering on panels. Wet the entire area down to remove loose dirt and grime, then hand wash one area at a time using your dedicated paint finish sponge or wash mitt. Wash from the top and work your way down, rinsing frequently to minimize grit abrasion. Follow with a final rinse of water. This process will remove most contamination from the RV's surface.
For stubborn stains such as road tar or bug stains, use an ammonia based glass cleaner or a small amount of rubbing alcohol on a damp cloth followed immediately by warm soapy water, and rinse with clean water. This may not dissolve the road tar, but it will loosen tar and bug stains and remove them from the surface.
Do not use solvent based cleaners on bird droppings or tree sap as these are water based stains. They can be dissolved using ammonia based glass cleaner, warm soapy water and a little "elbow grease". After removing stubborn stains immediately rinse with clean water.
Drying the RV is just as important as washing it. Tap water and well water contain many chemicals that could water stain your RV's finish.
We suggest using a damp natural or synthetic chamois. There are other drying products such as lint-free micro-fiber towels that work just as well.
Maintenance Record
Table of Contents
145
Section 13: Exterior
During cold weather Salt and other chemicals that are spread on winter roads in some geographical areas can have a detrimental effect on the recreation vehicle's underbody. If your recreation vehicle is exposed to these conditions, spray the underbody with a high-pressure hose every time you wash the exterior of your recreation vehicle. Take special care to remove mud or other debris that could trap and hold salt or moisture. After washing your recreation vehicle, wipe off all water drops from the rubber parts around the slideout and doors.
NOTE: When the slideout or door is frozen, opening it by force may tear off or crack the rubber gasket that is installed around the slideout or door. Therefore, pour warm water on the gasket to melt the ice (wipe off the water thoroughly after opening the slideout or door). To prevent the weather stripping from freezing, treat it with a silicone spray.
Waxing Wax your recreation vehicle once or twice a year, or when painted surfaces do not shed water well. Use a soft cloth to apply a small amount of wax to the painted surfaces. After the wax has dried, polish the recreation vehicle with a dry, soft cloth. Do not wax your recreation vehicle in direct sunlight. Wax it after the surfaces have cooled. Do not apply wax to any area having a flat black finish as it can cause discoloration. If the finish has been stained with wax, wipe off the area with a soft cloth and warm water. When waxing the area around the various openings, do not apply any wax on the weather strip. If it is stained with wax, the weather strip cannot maintain a weatherproof seal around the opening.
Do not use waxes containing high-abrasive compounds. Such waxes remove rust and stains effectively from the paint work, but they are also harmful to the luster of the painted surface since they scrape off the coating. Further, they are detrimental to glossy surfaces, such as the grille,
garnish, moldings, etc. Do not use gasoline or paint thinners to remove
road tar or other contamination to the painted surface.
Do not use a buffer and a buffing compound as it may damage the exterior surface. Please contact a professional paint body shop for assistance.
Polishing your recreation vehicle If painted surfaces have been severely damaged and have lost their original luster and color tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polishing to the damaged surface only; polish a somewhat wider area, moving the polishing cloth in one direction. After polishing, flush the compound from the surface and apply a coat of wax to regain a beautiful luster.
Damaged paint To prevent corrosion, touch up small cracks and scratches in the paint coat as soon as possible with touch-up film or paint. Carefully check the body areas facing the road and the tires for damage to the paint coat caused by flying stones, etc.
146
Maintenance Record
Table of Contents
Section 13: Exterior
Cleaning plastic parts Use a sponge or chamois to clean plastic parts. Use warm water and a soft cloth or chamois to remove any white residue from dark colored plastic surfaces. Do not use a scrubbing brush, other hard tools, or wax containing abrasives as they may damage the plastic surface.
Do not allow plastic to come into contact with brake fluid, engine oil, grease, paint thinner, or battery acid. These will damage plastic. Use a soft cloth and a mild detergent solution to wipe away any such contact.
Chrome parts To prevent chrome parts from spotting or corroding, wash with water, dry thoroughly, and apply a non-abrasive automotive wax. If the chrome is severely damaged or pitted, use a commercially available chrome polish product.
Frame
Frames receive heavy abuse from road conditions such as sand, pebbles, objects in the highway, and/or ice inhibiting chemicals, all of which will cause chipping and a blasting effect on the painted surface. Frames will show signs of rust much sooner when exposed to salty air. Periodically rinse off the frame (or as use requires) removing road grime, tar, oil, mud or salt. Refer to your Chassis Guide for the chassis manufacturer's maintenance instructions.
Mud Flap
Your motor home is equipped with rear wheel mud flaps and/or a deluxe full-width mud flap, periodically check and remove dirt or debris buildup from the mud flaps.
The mud flap(s) should never be tilted towards the exhaust pipe when the motor home is not in motion or when the motor home is moving in reverse. Caution should be used when parking the motor home to assure the mud flap does not become caught or hung up on stationary items on the ground. This could result in damage to the mud flap(s).
Exterior Roof and Sidewall Vents
Inspect the roof vents, including sealants for cracks and keep them clean. Inspect the refrigerator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.
Windows
To avoid exhaust gas entry into the motor home, keep windows closed when the chassis or generator engines are running.
Maintenance Record
Table of Contents
147
Section 13: Exterior
Any ventilating window may permit water inside, especially during heavy rainstorms or while driving. This is normal and water should only be seen in the lower track portion of the window frame. Condensation will also cause water to accumulate on windows and in the tracks. Ensure that the escape window latches are properly adjusted (the window will pop open if not adjusted tight enough).
Window glass The window glass can normally be cleaned with a sponge and water. Use glass cleaner to remove wax, oil, grease, dead insects, etc. After washing the glass, wipe it dry with a clean, soft cloth.
Exterior Ladder (if so equipped)
Your recreation vehicle may be equipped with an exterior roof ladder. The RV roof has decking under the rubber roof membrane to allow you to walk on the roof (with caution) to do maintenance.
If your recreation vehicle is equipped with a roof ladder, do not leave items attached to it while traveling. DO NOT exceed the weight rating of the ladder. The ladder weight capacity label is located under the bottom step of the ladder. There should never be more than one person on the ladder at the same time.
Self-Storing ladders: Make sure to pull all pins (there may be up to 4) to unlock the ladder. All pins must be re-inserted when locking the ladder open for use. LADDER CAPACITY MAXIMUM 300 lbs. (136 kg)
DO NOT exceed the ladder maximum weight rating. The maximum rating includes the person's weight PLUS weight of items
carried. When climbing:
Always face the ladder. Climb slowly with weight centered between side rails. Keep a 3 point contact on the ladder at all times (3 Point contact-
two hands and a foot or two feet and one hand). Keep hands free.
Use of accessories such as lanyards to keep carried items tethered will keep hands free and prevent falling items.
Heavy or bulky items should be brought up only after reaching the roof.
Do not use the ladder if damaged in any way. Failure to follow these guidelines could result in death or serious injury.
Some models may be equipped with a self-storing ladder mounted to the side of the vehicle. Self-Storing Ladder operation
1. Pull all the locking pins out of the ladder brackets (Fig. A).
2. Pull the ladder down and toward you and it will swing
away from the RV.
3. When the brackets are extended (Fig. B), re-insert the pins to lock the ladder in place while in use.
148
Maintenance Record
Table of Contents
Section 13: Exterior
4. To return the ladder to the storage position; pull the locking pins and push the ladder up and in towards the RV.
5. When the ladder is in the storage position, re-insert all locking pins to prevent the ladder from opening while traveling.
Sealants
To check the exterior sidewall sealants, use a stepladder placed safely alongside the vehicle. Do not prop a ladder against the body of the RV as it may damage the exterior finish.
Sealants perform a very important function and should be inspected closely and regularly maintained. We incorporate many different types of sealants, including butyl/putty, black Butyl-encapsulated foam, silicone (clear and color), roof sealant and foam. In general, sealants do not have "set" lifetimes. Varying environmental factors affect the pliability and adhesiveness of sealants. You or your dealer must:
Inspect all sealants a minimum of every six months. A quick walk around the motor home before leaving may help prevent potential problems during trips.
Have the sealant replaced if you notice any cracks, peeling, voids, gaps, breaks, looseness or any sign of physical deterioration.
Always use the same type of sealant that was removed. Your dealer service or parts manager can help you obtain the correct sealant(s).
The sealants may become damaged due to ultraviolet exposure, air pollution, freezing temperatures and exposure to other elements. Repair deteriorated sealants immediately to prevent damage. Cap seal all trim and openings at least once after the first year and thereafter as cracks, peeling, lifting and shrinkage occur.
Maintenance Record
Table of Contents
149
Section 13: Exterior
Notes:
150
Maintenance Record
Table of Contents
Section 14: Travel/Camping/Storage Checklists
Travel Checklist
Following is a preliminary list of items that need to be checked before leaving your home
or campsite. This is a general list, which you may want to customize as you determine your
own needs. Refer to your Chassis Guide for information on chassis pre-trip inspections and
maintenance.
Safety Make sure you follow all safety precautions noted in this owner's manual and in any manufacturer's operators manual when preparing to travel.
Before leaving home (or campsite): o Make sure all fluids are at proper levels (engine oil, transmission fluid, engine coolant, power steering fluid and windshield washer fluid). o Check the fuel gauge and lights on the motor home. Have someone observe the operation of all exterior lights while you activate the controls. Check the turn signal and high beam indicators on the instrument panel. o Examine the tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. o Check tire pressure and correct according to manufacturer specifications. o Check wheel nuts for tightness. o Inspect and work all interior and exterior latches and locks (lube if necessary). o Make sure the batteries are fully charged and installed correctly. o Turn ON the motor home 12-volt battery disconnect switch. o Inspect the power cord and carefully clean the contacts if necessary. Plug in the power cord to an appropriate power source. o Turn on the interior lights and check outlets for polarity. If needed, replace any blown fuses. Check the circuit breakers and test the GFCI circuits. o Inspect the propane gas system (if so equipped). If you have any questions, contact your independent dealer or a qualified propane gas service representative for assistance. If the propane system is functioning properly, test any pilot lights or direct spark ignition features. Do not travel with propane system on. o Inspect and test all safety detectors. If needed, replace any drained or discharged batteries. If you have a defective or damaged safety detector, replace it immediately. o Inspect the leveling jacks for operation. If needed, perform maintenance as per the manufacturer's information. o Test all exterior and interior lights. Replace any bulbs that are burnt out. o Prepare the chassis portion of the motor home for the camping season in accordance with the Chassis Guide. o Wash the exterior of the motor home. Do a sealant inspection and repair as necessary. o De-winterize and sanitize system. o If you are towing a vehicle, connect it to the motor home and test all connections and lights (if applicable). o Test brakes for proper operation. o Fill the fresh water tank. Disconnect, drain and store the garden hose on the bracket. o Check the seat belt buckles and release mechanisms for positive action and secure connections.
Maintenance Record
Table of Contents
151
Section 14: Travel/Camping/Storage Checklists
Before leaving the campsite: Check the area under the motor home after overnight parking and look for fuel, water, oil or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks (if so equipped). Empty black and gray holding tank, rinse as needed. Retract any awnings and secure them for transport. Close all the roof vents. Close windows & latch blinds. Disconnect the cable TV and phone hookups and lower the TV antenna. Turn off the interior lights, water heater, furnace and water pump. Secure any loose, heavy or sharp objects in the motor home or exterior compartments. Disconnect the power cord and ensure it is stored correctly. Disconnect any water connections. Water pump and water heater (if applicable) turned off. Fasten all interior and exterior doors securely. Lock them (if applicable). Latch drawers, cabinets & doors. Move slideout(s) in and lock it in place (if applicable). Walk around your motor home one last time to make sure everything is stored away and the baggage compartments are closed and locked. Refrigerator door locked. Furnace turned off. Make sure the leveling jacks are retracted to the travel position. Retract step. Secure and lock the entrance door.
Motor Home Storage
Properly preparing your motor home for storage during periods of non-usage will prevent problems from arising. It will also make it easier to get started again for the following camping trip or season. To prevent costly freeze-ups, winterize the plumbing system when it will not be in use for an extended period of time, especially if it is stored in colder climates.
Prior to storage: Prepare the chassis for storage in accordance to the Chassis Guide. Remember to use fuel additives and supplements if recommended. Wash and wax the exterior of the vehicle. Do a sealant inspection and repair as necessary. Inspect and clean tires. Check for wear, cracks and inflation pressure. Inspect and seal off any area that offers an entry point for rodents, birds or insects. Cover all external outlets (i.e. furnace, vents etc.). Damage from birds, rodents, insect, etc., is not covered under the "Motorized Transferable Limited Warranty" applicable to your motor home. Close all windows, roof vents and range hood vent. Turn the furnace thermostat(s) to the OFF position (if equipped). If your motor home is equipped with a gas/electric DSI range, light a range gas burner to consume any gas remaining in the lines. Once the flame extinguishes itself, turn the burner valve OFF. Drain all water lines. Make sure the motor home is winterized. Winterize the toilet and appliances (dishwasher, refrigerator, clothes washer).
152
Maintenance Record
Table of Contents
Section 14: Travel/Camping/Storage Checklists
Drain and flush all holding tanks (fresh water, gray water, black water and/or hot water tanks).
Adding fuel stabilizer to the generator will aid in preventing condensation and fuel varnishing.
Turn OFF the motor home 12-volt battery disconnect switch. Turn OFF the inverter mode at remote. Disconnect the batteries to prevent battery discharge. Remove all perishables from the refrigerator/freezer. Defrost, wash and dry the
interior of the refrigerator/freezer and prop (or block) the doors open so air can circulate and prevent mildew. Remove all perishables from the cabinets. Leave the cabinets and doors ajar to allow air circulation and prevent mildew and musty odors. Lubricate locks and hinges on exterior doors. While the motor home is being stored If the vehicle is stored outside in areas of heavy snow, you should periodically brush the snow off to prevent excessive accumulation and prevent possible roof damage.
Maintenance Record
Table of Contents
153
Section 14: Travel/Camping/Storage Checklists
Notes:
154
Maintenance Record
Table of Contents
Section 15: Additional Information
Featured Components Quick Reference Chart
Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
Component
Manufacturer
Website
Air Conditioner
Coleman-Mach
www.airxcel.com/colemanmach
Antenna, TV
Winegard
www.winegard.com
Awning
Lippert Components Carefree of Colorado Dometic
www.lci1.com www.carefreeofcolorado.com www.dometic.com
Camera, Back up/side view
ASA Electronics Rear View Safety
www.asaelectronics.com www.rearviewsafety.com
Electronic tems
components/sys- See manufacturers' user guide
Entrance Step
Lippert Components www.lci1.com
Fan, Exhaust 12V
Atwood Maxx Fan
www.atwoodmobile.com www.airxcel.com/maxxair/ products/fans
Fireplace
Twinstar Furrion
www.twinstarhome.com www.furrion.com
Furnace
Atwood
www.atwoodmobile.com
Generator
Onan
www.power.cummins.com/rv
Inverter
Magnum Energy
www.magnumenergy.com
Leveling Jack System
Equalizer Systems Lippert Components
www.equalizersystems.com www.lci1.com
Microwave
See manufacturers' user guide
Outside Center
Shower
/
Utility B & B Molders
www.bandbmolders.com
Propane Tank
Manchester Tank
www.mantank.com
Propane/Carbon Alarm
Monoxide See manufacturers' user guide
Propane Regulator
Manchester Tank
www.mantank.com
Range/stove/cooktop
Atwood Suburban
www.atwoodmobile.com www.airxcel.com/suburban/ products/cooking
Range hood
Ventline Inc.
www.ventline.com
Refrigerator
Norcold
www.norcold.com
Safety Alarms Satellite System Tank Sprayer/BLK
Thermostat
See manufacturers' user guide
Winegard
www.winegard.com
B & B Molders
www.bandbmolders.com
Coleman-Mach
www.airxcel.com/colemanmach
Maintenance Record
Table of Contents
155
Section 15: Additional Information
Toilet
Water Heater, Tank DSI Water Heater, Tankless
Water Pump, 12V
Thetford Corp.
Atwood Greenbrier Girard Systems
Shurflo East
www.thetford.com
www.atwoodmobile.com www.greenrvproducts.com
www.shurflo.com
156
Maintenance Record
Table of Contents
Section 15: Additional Information
Vehicle Maintenance Record
Make: Model: Model Year: Vehicle Serial#: Engine: Engine Serial#:
Service Date
Mileage
Work Performed
Performed By
Notes
Maintenance Record
Table of Contents
157
Section 15: Additional Information
Notes:
158
Maintenance Record
Table of Contents
Section 15: Additional Information
Jayco
Ownership Notification Fax Form To: (800) 825-7876
ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated.
Change of Owner
Transfer of Limited Warranty (If Applicable - see limited
warranty for details)
Model Information: Serial#: _____________________ Chassis #: _______________________ Odometer Reading ______________
(Motorized only)
New Owner Information: Purchased Date: ________________ Name: _________________________________________________________ Address: _________________________________________________________ City: ____________________ State/Province: ______ Zip Code_________ Phone # ___________________ E-Mail Address _________________________
Previous Owner Information: Purchased Date: ________________ Name: _________________________________________________________ Address: _________________________________________________________ City: ____________________ State/Province: ______ Zip Code_________ Phone # ___________________ E-Mail Address _________________________
Maintenance Record
Table of Contents
159
Suburban - RV Water Heaters, Furnaces, Ranges & Cooktops
ASA Electronics® mobile technology starts with us.
Outdoor Adventure Starts Here | This Way Out | Dometic USA
Outdoor Adventure Starts Here | This Way Out | Dometic USA
Welcome to EQ Systems - EQ Systems
RV & Marine Multiplex Systems | Firefly Integrations
Furrion
greenrvproducts.com
Jayco - High Quality & Design - Award Winning RVs | Jayco
JayCoRVClub - Unleash Your Adventurous Spirit
lci1.com
DC to AC Power Inverters | Pure Sine & Modified Sine Inverters | Dimensions
Thetford: Trustworthy RV Products for Adventure
Back Up Camera, RV Backup Camera, RV Camera System – Rear View Safety
RV Water Delivery Pumps | RV Pumps | Pentair
Défauts et rappels des véhicules, des pneus et des sièges d’auto pour enfant
Thetford: Trustworthy RV Products for Adventure
Home - Twin Star InternationalTwin Star International
Winegard Company
Jayco - High Quality & Design - Award Winning RVs | Jayco