Assembly Instructions for Round Daybed with Canopy
Model Numbers: WF316855 (N717P229922), WF316856 (N717P229923), WF316857 (N717P229924)
For any questions, please contact us at: lowesteam@aminalife.com
General Notice
- Tighten screws to 50% before fixing all bolts. An Allen wrench is recommended over an electric drill.
- Place the item on a flat surface to ensure stability during assembly.
- Gradually tighten all screws.
- If screws are not aligning with holes, loosen other screws to 50% and continue assembly.
- If the item is unstable, loosen all screws, adjust on a flat surface, and retighten.
- Note: Fully tightening some screws early may cause misalignment with others. All holes are designed to be slightly larger to accommodate adjustments.
Part List
Frame Components:
- Part A: Curved Frame Section (1 pc)
- Part B: Curved Frame Section (1 pc)
- Part C: Curved Frame Section (1 pc)
- Part D: Curved Frame Section (1 pc)
- Part E: Base Support (4 pcs)
- Part F: Vertical Support (6 pcs)
- Part G: Curved Seat Base (4 pcs)
- Part H: Curved Back Support (2 pcs)
- Part I: Curved Back Support (2 pcs)
Canopy and Cushion Components:
- Part J: Seat Cushion (4 pcs)
- Part K: Round Table Top (1 pc)
- Part L: Cushion (5 pcs)
- Part M: Canopy Arch (1 pc)
- Part N: Canopy Arch (1 pc)
- Part O: Canopy Arch (1 pc)
- Part P: Canopy Arch (1 pc)
- Part Q: Canopy Arch (1 pc)
- Part R: Canopy Arch (1 pc)
- Part S: Canopy Arch (1 pc)
- Part T: Canopy Arch (1 pc)
- Part U: Canopy Connector (1 pc)
- Part V: Base Support Cylinder (1 pc)
Hardware List
- 1: M6x40mm Bolt (10pcs + 1 extra)
- 2: M6x35mm Bolt (8pcs + 1 extra)
- 3: M6x30mm Bolt (52pcs + 3 extra)
- 4: M6x15mm Bolt (26pcs + 2 extra)
- 5: M6x16x1mm Washer (96pcs + 3 extra)
- 6: M6x16x5mm Plastic Washer (8 pcs + 1 extra)
- 7: M4x13mm Screw (4pcs + 1 extra)
- 8: M6 x 15 mm Feet cap (28pcs + 2 extra)
- 9: M4*60 Allen Key (1pc)
- 10: M4*60 Allen Key (2pcs)
- 11: Gas Bar (2pcs)
- 12: Keeper Plate (1pc)
- 13: Keeper Plate (12pcs)
- 14: M4*60 Allen Key (1pc)
Assembly Steps
Step 1-4: Assemble the base frame sections (A, B, C, D) using bolts (1, 5) and feet caps (8). Ensure initial tightening to 50%.
Step 5-6: Attach vertical supports (F) and base supports (E) to the frame sections using bolts (4, 5) and keeper plates (13).
Step 7-8: Continue assembling the frame with curved back supports (H, I) and base supports (G) using bolts (3, 5).
Step 9-11: Further assemble the main structure, connecting various frame components using bolts (4, 5) and keeper plates (13).
Step 12-13: Attach the remaining frame components and base supports (E) using bolts (1, 4, 5) and keeper plates (12).
Step 14-17: Assemble the canopy structure by connecting the canopy arches (M, N, O, P, Q, R, S, T) using bolts (7) and Allen keys (9).
Step 18: Connect the assembled canopy structure (U) to the main daybed frame.
Step 19-21: Attach the seat cushions (J) and additional cushions (L) to the daybed.
Step 22-23: Assemble the round table by placing the table top (K) onto the base support cylinder (V).
Step 24-25: Attach the remaining curved back supports (H, I) and frame components using bolts (1, 5) and feet caps (8).
Step 26-27: Connect the curved seat bases (G) and frame components using bolts (3, 5).
Step 28-29: Finalize the assembly by attaching the remaining components and seat cushions (J).
Final Check
Ensure all screws are fully tightened and the daybed is stable.
