One For All URC7125 Evolve 2 Simple Set Up Guide

This guide provides instructions for setting up and using your One For All URC7125 Evolve 2 remote control.

Key Table

How to Set Up Your Remote

A - SimpleSet

SimpleSet is a quick and easy way to set up the remote for popular brands. It typically takes less than a minute per device.

Device Modes and Types

Brand Lists

For each device type, locate your brand and its assigned number.

TV Brands

STB Brands

SimpleSet Setup Steps

1. Turn on your device (not on standby) and point the OFA remote towards it.
2. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
3. Press the MODE key repeatedly until the LED for the device you want to set up is lit.
4. Hold down the digit corresponding to your brand and device (e.g., 6 for Samsung TV).
5. The remote will send a Power signal every 3 seconds until your device switches off.
6. As soon as your device switches off, release the digit.
7. The LED will blink twice and go out. The remote should now operate your device. ✅

? If one or more keys do not work as expected, start again at step 1. The remote will try the next code in its memory.

B - Set Up By Code

Use this method if your brand is not listed in section A. You will try codes individually.

Code Setup Steps

1. Turn your device on (not on standby).
2. Locate your brand in the code list (refer to pages 126-137 in the full manual for a comprehensive list). Codes are organized by Device Type and Brand.
3. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
4. Press the MODE key repeatedly until the LED for the device you want to set up is lit.
5. Enter the first 4-digit code listed for your brand (e.g., 4542 for an Aiwa TV).
6. The LED will blink twice and go out.
7. Aim the remote towards your device and press the POWER key.
8. If the device turns off, your remote is ready to use. If not, repeat steps 3-7 with the next code in the list. ✅

? Some codes are very similar. If keys do not operate as expected, try again from step 3 with the next code.

Advanced Features

Learning Functions

Your One For All remote can learn any function from any other working remote control. This is useful if you are missing functions from your original remote. You can learn onto any key except MAGIC or MODE. You can also learn a complete device if its code is not found.

Ensure you have all original remote controls with working batteries to hand.

Position the original remote approximately 3-5 cm from the OFA remote, pointing towards it.

Learning Steps

1. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press the MODE key repeatedly until the LED for the device you want to learn functions on is lit.
3. Press 975. The LED will blink twice.
4. Press and release the key on the OFA remote you want to learn a function onto (e.g., the HOME key). The red LED will blink continuously.
5. Press and release the corresponding key on the original remote.
6. The LED will blink twice to indicate the key has been learned correctly. ✅
7. Repeat steps 4 and 5 for each key you want to learn. You can learn from multiple remotes, but only one function per key.
8. When you have learned all required functions, press and hold the MAGIC key until the LED blinks twice and turns off.

Hints

• ? If the LED shows one long blink at step 6, the function was not learned correctly. Please try again from step 4.
• ? If keys do not work properly after setup, you can re-enter learning mode anytime by repeating step 1.

To Delete a Learned Function

1. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Using the MODE key, make sure the LED for the device you want to delete functions from is lit.
3. Press 976. The LED will blink twice.
4. Press the key to delete twice. The LED will blink twice. ❌

Activities: Watch TV Mode

The WATCH TV feature combines TV and STB into a single mode. In this mode, the Volume and AV keys control the TV, while the rest of the keys control the STB.

When the AV key is pressed in WATCH TV mode, the MENU, Up, Down, Left, Right, and OK keys temporarily control the TV. These keys revert to controlling the STB if the OK key is pressed or if no key is pressed for ten seconds.

Holding the POWER key for 2 seconds in WATCH TV mode sends the Power function for both the TV and STB.

The NETTV Feature

The Evolve remote features a NETTV key for accessing digital TV and streaming services over the internet (e.g., Netflix, YouTube, Amazon Prime). If your original remote had a similar key, it will perform the same function. If not, you can program it as a shortcut using a macro.

Programming the NETTV Macro

1. Ensure your device is switched on (not on standby).
2. Hold down the NETTV key until the LED blinks twice and stays lit.
3. Use the MODE key to select the device you want to use for the NETTV macro (e.g., TV).
4. Now perform the sequence of keys exactly as you normally would to launch your streaming service. The remote records the sequence in real time.
5. Once the streaming service has started on your device, hold down the NETTV key until the LED blinks twice and goes out. The macro is now stored.

Tips for NETTV Macro

• ? Make sure the remote is operating the device before programming.
• ? If the macro doesn't work as expected, you can repeat the sequence to reprogram it.
• ? Wait for your device to respond before pressing the next key during programming. The remote remembers the timing.
• ? The NETTV macro is tied to one device. Ensure you are controlling the correct device when using it.

Macros

Program a Macro

You can program any key (except MAGIC or MODE) to send multiple commands with a single press. This is useful for setting multiple devices to a specific state (e.g., turn on TV to HDMI 1 and power on STB).

Macro Programming Steps

1. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press 995. The LED will blink twice.
3. Select the key on the OFA remote you want to program the macro onto.
4. Use the MODE key to select the device for the first function of the macro (e.g., TV).
5. Press the key you want to include in the macro (e.g., the AV key).
6. Repeat steps 4 and 5 if necessary to add more keys to the macro. You can include up to 15 key presses.
7. To store the macro, hold down the MAGIC key until the LED blinks twice.

? If the LED shows a long blink when you press a key in steps 4 or 5, you have entered too many keys. Please try again.

Deleting a Macro

To remove a macro from a key:

1. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press 995. The LED will blink twice.
3. Press the key on which the macro is programmed.
4. Now hold down the MAGIC key until the LED blinks twice. The macro is deleted. ❌

Volume Lock

If you always use one device (e.g., your TV) to control volume, you can set the One For All remote to always use that device's volume controls, regardless of which device the remote is currently controlling.

To Lock Volume to a Specific Device:

1. Hold down the MAGIC key until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press 993. The LED will blink twice.
3. Use the MODE key to select the device you want to lock the volume to.
4. Press the MAGIC key once. The LED will blink twice, and volume is now locked. ✅

To Unlock Volume:

To unlock the volume and set every device back to controlling its own volume:

1. Hold down the MAGIC key until the LED under the TV key blinks twice. The LED under the current mode key will stay lit.
2. Press 993. The LED will blink twice.
3. Press the VOLUME UP key. The LED will blink twice, and volume is now unlocked. ✅

Product Information

Product Disposal

This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means it must be handled according to European directive 2012/19/EU to be recycled or dismantled, minimizing environmental impact. Users can give this product to a competent recycling organization or the retailer when purchasing new equipment.

Battery Disposal

(EUROPEAN DIRECTIVE 2006/66/EC) Please do not dispose of batteries with normal household waste. Inform yourself about local separate collection for empty batteries to ensure correct disposal, preventing potential negative effects on the environment and human health.

Warranty

Universal Electronics Inc./One For All warrants to the original purchaser that this product will be free from defects in materials and workmanship under normal use for a period of one (1) year from the date of original purchase. This product will be replaced free of charge if proven defective within the warranty period. This warranty does not cover consumables like batteries, or damage to cabinets. Proof of purchase is required for warranty service. National consumer rights may also apply.

For support and more information, visit: www.oneforall.com

Manufacturer/Distributor:
Universal Electronics BV
Europe & International
Colosseum 2, 7521 PT Enschede
The Netherlands

Part Numbers: URC7125, 711733, RDN-1010519