Victrola 8-in-1 Bluetooth Record Player & Multimedia Center

Listening to a Vinyl Record

1. Press the "PHONO" button.
2. Open the top cover.
3. Place a vinyl record on the turntable, using the 45 RPM adapter if necessary.
4. Select the appropriate speed (33-1/3, 45, or 78 RPM).
5. Release the tone arm by gently pushing the tone arm clip.
6. Lift the tone arm using the cue lever.
7. Move the tone arm to the record's edge. The turntable will start.
8. Gently lower the tone arm using the cue lever.
9. When the record ends, the tone arm and rotation stop. Manually return the tone arm to its rest.

Important: Close the top cover to prevent dust. Relock the tone arm clip before transporting.

Listening to a CD/MP3 CD

1. Press the "CD/USB" button to select CD mode.
2. Press the EJECT button (▲) to open the disc tray.
3. Place a disc on the tray with the label facing up.
4. Press the EJECT button (▲) to close the tray.
5. The unit will display "READ" and then the track count.
6. Press PLAY/PAUSE (II) to begin playback.
7. Press PLAY/PAUSE (II) to pause; press again to resume.
8. Use skip buttons (◄◄ or ►) to navigate tracks. Press (◄◄) once to restart the current track, twice for the previous track. Press (►) for the next track. Hold to fast forward/rewind.
9. Press STOP (■) to stop playback.

Repeat Playback: Press REPEAT to cycle through REPEAT 1, REPEAT FOLDER (MP3 CD only), or REPEAT ALL. Repeat mode cancels if other source buttons are pressed.

Shuffle Playback: Press SHUFFLE to play tracks in random sequence. Shuffle mode cancels if other source buttons are pressed.

Programmed Playback: While the CD is stopped, press PROGRAM, select track numbers using (◄◄ or ►), and press PROGRAM again to set each track. Press PLAY to start programmed playback. Press STOP to cancel.

Listening to the Radio

1. Press the "AM/FM" button to select AM or FM.
2. Tune to the desired station using the Radio Tuner Knob. The "TUNED/ST" indicator lights up for stereo reception in FM mode.

Adjusting for Best Reception: Rotate the unit for AM broadcast. Extend and reposition the FM antenna for FM broadcast.

Listening to an External Audio Device (AUX Mode)

Connect an external audio source (iPod, MP3 Player, etc.) using the AUX-IN jacks (front or rear). Use a 3.5mm cable for headphone jacks or RCA cables for other sources. Press "AUX/Bluetooth" to select AUX-IN mode. Control playback via the external device.

Note: If both front and rear AUX-IN jacks are connected, only the front jack is active.

Listening to an External Audio Device (Bluetooth Mode)

Press "AUX/Bluetooth" twice to select Bluetooth mode. Enable Bluetooth on your external device and search for "Wooden Music Center". Pair the device (use "0000" if a password is required). Control playback using the unit's buttons or the external device.

Note: Effective distance is 10 meters (33 ft).

Listening to a Cassette Tape

1. Load a cassette tape into the unit. Playback begins automatically.
2. Press the button halfway to fast forward. Press fully to end playback and eject.

USB Memory Stick Playback

1. Press "CD/USB" repeatedly to select USB mode.
2. Connect the USB memory stick to the USB slot.
3. Press PLAY/PAUSE (II) to begin playback.
4. Press PLAY/PAUSE (II) to pause; press again to resume.
5. Use Folder up/down buttons to choose folders.
6. Use skip buttons (◄◄ or ►) to navigate tracks. Press (◄◄) once to restart the current track, twice for the previous track. Press (►) for the next track. Hold to fast forward/rewind.
7. Press STOP (■) to stop playback.

DELETE Function: When USB is stopped, press DELETE, then use Rewind/Fast Forward buttons to select DEL ONE, DEL FOLDER, or DEL ALL, then press DELETE to confirm.

REPEAT PLAYBACK: Press REPEAT to cycle through REPEAT 1, REPEAT FOLDER, or REPEAT ALL.

Shuffle Playback: Press SHUFFLE to play tracks in random sequence.

Programmed Playback: While USB is stopped, press PROGRAM, select track numbers using (◄◄ or ►), and press PROGRAM again to set each track. Press PLAY to start programmed playback. Press STOP to cancel.

USB Recording Function

Audio from PHONO, TAPE, CD, or AUX/BLUETOOTH can be recorded to USB in MP3 format.

Recording Steps:

1. Insert a USB memory stick.
2. Select the source (PHONO, TAPE, AUX, or CD).
3. If recording from vinyl, place the record and needle.
4. Press the Record button to start recording. The display will show recording status.
5. Press the STOP button when finished.

Manual Track Increment: During recording, press (►►I) to end the current track and start a new one.

Note: Recording stops if the source is disconnected for 15 minutes.

CD to USB Recording Function

Follow these steps to record from CD to USB:

1. Connect the USB memory stick.
2. Select CD mode and load a CD/MP3 CD.
3. If the CD is playing, press STOP.
4. Press the RECORD button to enter recording mode.
5. Select "record one", "record folder" (MP3 CD only), or "record all" using the skip buttons.
6. Press the RECORD button again to start recording.
7. Pressing the STOP button will cancel the recording.

Note: Only the STOP button works for cancelling when recording from CD.

Maintenance / Proper Handling

Compact Disc Handling:

• Place discs label-side up.
• Handle discs by edges or label.
• Clean discs with a soft, dry cloth from center outward. Avoid chemicals.
• Return discs to cases after use.
• Do not expose discs to direct sunlight, high humidity, or high temperature.
• Use soft felt-tipped pens for labels. Avoid ball-point or hard-tipped pens.
• Do not use irregularly-shaped CDs.
• Never handle discs with dirty fingers or insert cracked discs.

Handling Vinyl Records:

• Do not touch grooves; handle by edges or label with clean hands.
• Wipe records with a soft anti-static cloth.
• Keep records in protective sleeves, stored upright.
• Avoid direct sunlight, heat sources, vibration, dust, extreme temperatures, or moisture.

General Care:

• Pull the power plug directly from the wall outlet; never pull the cord.
• Keep the laser pickup clean; do not touch it. Close the disc tray.
• Clean the unit with a clean, dry cloth. Avoid chemical solvents.
• Unplug the unit if not in use for an extended period.

How to Replace the Turntable Stylus:

The stylus should be replaced after approximately 50 hours of use or when sound quality degrades. Worn styli can damage records.

Removing the old stylus: Set a screwdriver at the tip and push downward. Pull the stylus downward and forward.

Installing a new stylus: Hold the front tip, insert the rear edge first, then push upwards until it locks into place. Caution: Do not remove or bend the stylus. Do not touch the needle. Turn off power before replacing. Keep out of reach of children.

Specifications

Troubleshooting Guide

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment into an outlet on a different circuit, or consulting a dealer or experienced radio/TV technician.

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

The device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC Statement

This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d'Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.

Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'expossition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel La réduction aux expositions RF peut être augmentée si l'appareil peut être conserve éaussi loin que possible du corps de l'utilisateur ou que le dispositif est régél sur la puissance de sortie la plus faible si une telle fonction est disponible.

California PROP 65 Warning

WARNING: This product contains chemicals known to the State of California to cause birth defects or other reproductive harm. For more information on these regulations and a list of chemicals, log on the following website address: http://www.oehha.ca.gov/prop65.html

Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics LLC.

Innovative Technology Electronics LLC. Limited Warranty: 90 Days Labor, One Year Parts

Innovative Technology Electronics LLC. (IT) warrants the product to be free from "Defects" in materials under normal use for a period of "One Year" from the date of the original purchase. The Warranty is "Not" transferable. IT agrees, within the initial "90 Day" period, to repair or replace the product if it is determined to be defective at "No Charge". It is further agreed that IT will cover the cost to repair or replace damaged "Parts" only for a total period of "One Year" from the date of the original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to improper voltage supply or settings, misuse, mishandling, accident, acts of God or attempted repair by an unauthorized service agent.

To obtain service: The purchaser MUST present an original sales receipt / proof of purchase. Please contact us at www.victrola.com to request an RMA (Return Material Authorization) number to return products for service or replacement. Returns without an RMA number on the package will be refused and returned to sender. Upon receipt of the returning item and our full inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent value and features. To return an item, supply full name, return address, phone number, item purchased, receipt of purchase and reason for return to obtain RMA number. All returns must be in the original packaging or reasonable substitute to prevent damage. Customer "Must" include full name, shipping address and telephone number inside of package. No return will be shipped back to a PO Box or APO address.

Please include your check or money order in the amount of:

• USD $5.00 for items $10.00 to $39.99 (Price Paid Per Unit)
• USD $10.00 for items $40.00 to $99.99 (Price Paid Per Unit)
• USD $16.00 for items $100.00 and up (Price Paid Per Unit)
• Shipping fees are non-refundable

Shipping fees are payable to Innovative Technology Electronics LLC. (IT) will not be responsible for delays or unprocessed claims resulting from a purchaser's failure to provide any / all of the necessary information.

Send all inquiries or RMA request via our website www.victrola.com/pages/technical-support.

Innovative Technology Electronics LLC.
1 Channel Drive
Port Washington, NY 11050
Toll free: 1-877-483-2497
Website for support: www.victrola.com/pages/technical-support

There are no express warranties except as listed above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER. (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Victrola Wooden Stand for Wooden Music Centers

Model: VA-30

Instruction Manual

PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE AND KEEP IT FOR FUTURE REFERENCE.