Outsunny A20-140 Tent

Safety Precautions

WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT.

This tent is not fireproof. The fabric will burn if left in continuous contact with a flame source.

Precautions:

• Do NOT use candles, matches or other open flames in or near a tent.
• Fuel-powered lanterns and appliances are NOT recommended for use in or near a tent. If fuel-powered lanterns or appliances such as wood stoves or electric heaters are used, exercise extreme caution. Keep them away from the tent walls. Do NOT leave them unattended. Turn them off before going to sleep. Make sure the tent is well ventilated at all times to avoid suffocation.
• Build campfires downwind and several metres away from a tent. Extinguish campfires before leaving a campsite or going to sleep.
• Do NOT fuel lamps, heaters or stoves in a tent.
• Do NOT smoke in a tent.
• Do NOT store flammable liquids in a tent.
• Keep exits clear.
• Do NOT apply any foreign substance to a tent. It may diminish the flame resistant properties of tent material(s).

Parts Included

• A: Tent Body (x1)
• B: Tent Poles (x3)
• C: Stakes (x15)
• D: Carry Bag (x1)

Setup Instructions

Step 1: Lay out the tent body.

The main tent fabric is laid out flat on the ground.

Step 2: Assemble tent poles.

Three segmented tent poles (B) are assembled by connecting the sections. Arrows indicate the direction of connection. A close-up shows the elastic cord inside the poles.

Step 3: Insert poles into tent.

The assembled tent poles are bent into an arc and inserted into grommets or loops at the corners of the tent body. Red arrows indicate insertion points.

Step 4: Secure poles to tent.

The tent poles are attached to the tent structure via clips. A close-up shows a clip being attached to a pole, with "x2" indicating two clips are used for this connection.

Step 5: Attach remaining poles.

More poles are attached to the tent structure using clips. A close-up shows clips being attached, with "x2" indicating two clips.

Step 6: Secure tent to poles.

The tent fabric is secured to the poles using numerous clips. A close-up shows clips being attached to the poles, with "x12" indicating twelve clips are used in total for this stage.

Step 7: Stake out the tent base.

Stakes (C) are driven into the ground at a 45-degree angle to secure the base of the tent. A close-up shows a stake being inserted, with "x4" indicating four stakes are used for this section.

Step 8: Attach rainfly.

The rainfly is placed over the tent structure and secured with clips. A close-up shows clips being attached, with "x2" indicating two clips.

Step 9: Stake out guylines.

Guylines are attached to the tent and then staked to the ground at an angle. A close-up shows stakes being inserted, with "x4" indicating four stakes for the guylines on one side.

Step 10: Adjust guylines.

The guylines are tensioned and staked to the ground at a 45-degree angle for stability. A close-up shows stakes being inserted, with "x4" indicating four stakes for the guylines on this side.

Step 11: Secure rainfly vents.

Ventilation openings on the rainfly are secured with clips. A close-up shows clips being attached, with "x2" indicating two clips.

Step 12: Final tent setup.

The final setup of the tent is shown, with all poles, guylines, and stakes in place, indicating a taut and stable structure.

Step 13: Optional car attachment.

The tent is shown attached to the side of a car, suggesting a car-compatible design.

Folding Instructions

Step 1: Remove stakes and guylines.

Stakes are removed from the ground.

Step 2: Detach rainfly.

Clips securing the rainfly are released.

Step 3: Remove poles from tent.

Poles are detached from the tent structure. A close-up shows clips being released, with "x4" indicating four clips.

Step 4: Disassemble poles.

Tent poles are disassembled into individual sections. A close-up shows pole sections being pulled apart, with "x12" indicating the number of pole segments and "x4" indicating clips.

Step 5: Fold tent body inwards.

The tent fabric is folded inwards towards the center. Red arrows indicate the direction of folding.

Step 6: Fold tent in half lengthwise.

The tent is folded in half lengthwise.

Step 7: Fold again.

The tent is folded again.

Step 8: Fold into thirds.

The tent is folded into thirds.

Step 9: Fold into quarters.

The tent is folded into quarters.

Step 10: Fold into eighths.

The tent is folded into eighths.

Step 11: Roll the tent.

The folded tent is rolled up tightly.

Step 12: Place rolled tent into carry bag.

The rolled tent is placed into the carry bag (D).

Step 13: Secure carry bag.

The carry bag is closed with its fastening.

Step 14: Final packed state.

The final, compact packed state of the tent in its carry bag is shown.

Customer Support

For any questions, please contact the customer care center. Details are provided below for various regions:

US Support

Contact: 001-877-644-9366, customerservice@aosom.com

Imported by: Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA. Made in China.

Canada Support

Contact: 416-792-6088, customerservice@aosom.ca

Imported by: Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9. Made in China.

UK Support

Contact: 0044-800-240-4004, enquiries@mhstar.co.uk

Importer Address: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. Made in China.

France Support

Contact: 0033-1-84166106, aosom@mhfrance.fr

Imported by: MH France, 2, rue Maurice Hartmann, 92130 Issy-les-Moulineaux, France. Fabriqué en Chine.

Spain/Europe Support

Contact: 0034-931294512, atencioncliente@aosom.es

Importer: Spanish Aosom, S.L., C/ Roc Gros, nº 15. 08550, Els Hostalets de Balenyà, Spain. B66295775. Made in China.

Portugal Support

Contact: 0034-931294512 (SEG-SEX DAS 7:30H ÀS 16:30H), info@aosom.pt

Importer: SPANISH AOSOM, S.L, C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ. WWW.AOSOM.PT

Germany Support

Contact: 0049-0(40)-88307530, service@aosom.de

Importer/Manufacturer/REP: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany. Made in China.

Italy Support

Contact: 0039-0249471447, clienti@aosom.it

Importer/Manufacturer/REP: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI). P.I.: 08567220960. Made in China.

Recycling Information: [Recycle symbol] Dispose of packaging responsibly. Association for waste management information: quefairedemesdechets.fr