JAMARA SCX 2.4 GHz Transmitter and Receiver

General Information

JAMARA e.K. is not liable for any damage caused to the product itself or through this, provided this is due to improper operation or handling errors. The Customer alone bears the full responsibility for the proper use and handling, including without limitation, the assembly, the charging process, the use and choice of the operation area. Please refer to the operating and user instructions, it contains important information and warnings.

Declaration of Conformity

JAMARA e.K. declares that the product "SCX 2,4 GHz, No. 061172" complies with Directive 2014/53/EU, 2011/65/EU. The full text of the EU Declaration of Conformity is available at: www.jamara-shop.com/Conformity

Important Warning

⚠️ For model building only - Not a toy! Read the complete instructions and security instructions carefully before using the model. Caution! Please fully and carefully read warnings/ safety instructions. These are for our own security and can avoid accidents/injuries.

Kit Contents

• Transmitter
• Receiver
• Instruction Manual

Recommended Accessories

• 8 x AA Batteries (Ord. No. 140267 (4 pieces))

Features

• 2 Channel 2.4 GHz Transmitter
• 3 Channel 2.4 GHz Receiver
• 2 Servo Reverse switches
• 2 Trim Sliders
• Charging socket
• Programmable fail-safe on the receiver

Technical Data - Transmitter

Technical Data - Receiver SCX 2.4 GHz

(Ord.No. 06 1171)

Safety Adherence

Following should be strictly adhered to:

• Before switching on the system, ensure that the throttle stick is in the off position.
• Check that the transmitter and receiver are compatible and bonded to one another.
• Always switch the transmitter on first and then the receiver.
• Always switch the receiver off first and then the transmitter.
• Complete a full range and function test before every take-off.
• Never over-fly people and do not allow your model to endanger people or animals.
• Do not fly near to over-head cables, buildings or airfields.
• The system must not be operated in rain, or thunder storms.
• If you do not intend to use the transmitter for a long period, remove the batteries.

Frequency Bands

Frequency bands: 2.4 GHz

Frequency range: 2405.5 - 2475.0 MHz

EIRP: < 5 mW (max. power transmitted)

Transmitter Controls

The transmitter features the following controls:

• 1. Antenna: For signal transmission.
• 2. Handle: Ergonomic grip.
• 3. Power LED: Indicates the transmitter is powered on.
• 4. Servo Reverse CH 1: Reverses the direction of Channel 1 servo.
• 5. Left/Right Stick: Controls steering (direction).
• 6. Left/Right Trim: Fine adjustment for steering neutral position.
• 7. Binding Button: Used for binding the transmitter to the receiver.
• 8. ON/OFF Switch: Powers the transmitter on and off.
• 9. Throttle Stick: Controls forward/reverse and speed.
• 10. Throttle Trim: Fine adjustment for throttle neutral position.
• 11. Servo Reverse CH 2: Reverses the direction of Channel 2 servo.
• 12. Indicator LED: Provides status information.

Battery Hatch

The battery hatch is located on the rear side of the transmitter. To open, push down on the marked 'Push' area and slide the cover away. When fitting batteries, be very careful not to short circuit them by observing the correct polarity.

Receiver

The receiver offers direct connections for up to two servos.

Receiver Channel Allocation:

• Channel 1: Steering
• Channel 2: Throttle
• Binding Channel 3: Binding Cable

Binding Transmitter and Receiver

As with all 2.4 GHz systems, the transmitter and receiver must be bound together. This process is vital for the system to function.

1. Fit the binding plug to socket 3 on the receiver and connect the power supply. The receiver LED will begin to blink.
2. Press and hold down the binding button on the transmitter and switch the power on. This will put the transmitter into binding mode.
3. Once the binding process has finished, the receiver LED will shine solid.
4. Switch the transmitter and receiver off.
5. Remove the binding plug. The transmitter is now ready for normal operation.

Important Information

The system will not function whilst the binding button is pressed. Do not leave the system in binding mode for long periods.

Settings

Before operating your model, carefully check that the servos operate in the correct direction. If they do not, use the servo reverse switches on the transmitter to change the direction. Set the servo neutral positions by moving the servo arms until they are at exactly 90º with the trim central. The trim should only be used for fine adjustments during operation. For models with internal combustion engines, ensure that the linkage cannot bind at full throttle or tick-over positions.

Switching On and Off

Switching On:

1. Connect all components together.
2. Switch on the transmitter.
3. Connect the power supply to the receiver.
4. Check that all LEDs are correctly illuminated. The system is now switched on and ready to operate.

Switching Off:

1. Switch off and unplug the receiver power supply.
2. Switch off the transmitter.

Operating the Model

Steering

This function is used to steer the model in the correct direction. Moving the steering stick to the left or right will make the wheels (or hull if operating a boat) move in that direction. Moving the stick to the left should make the model steer to the left.

Throttle

This function controls forward/reverse movement and speed. Pushing the stick forwards makes the model accelerate forwards. Pulling it to the rear will make the model brake first and then accelerate in reverse.

Disposal Restrictions

Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. You are obliged to take out the batteries, if possible, and to dispose of the electrical equipment at communal collection points. If personal data is stored on the electrical appliance, you must remove it yourself.

Service Assistance

For service and support, please contact the following authorized distributors:

Reitter Modellbau Versand (Germany)

Patricia Reitter
Degerfeldstrasse 11
72461 Albstadt, Germany
Tel: 07432 9802700
Fax: 07432 2009594
Mail: info@modellbauversand.de
Web: www.modellbauversand.de

Bay-Tec (Germany)

Martin Schaaf
Am Bahndamm 6
86650 Wemding, Germany
Tel: 07151 5002192
Fax: 07151 5002193
Mail: info@bay-tec.de
Web: www.bay-tec.de

Modellbau Zentral (Switzerland)

Peter Hofer
Bresteneggstrasse 2
CH-6460 Altdorf, Switzerland
Tel: +41 79 429 62 25
Mobil: +41 41 870 02 13
Mail: info@modellbau-zentral.ch
Web: www.modellbau-zentral.ch

JAMARA e.K. (Germany)

Manuel Natterer
Am Lauerbühl 5
DE-88317 Aichstetten, Germany
Tel: +49 (0) 75 65/94 12-0
Fax: +49 (0) 75 65/94 12-23
Mail: info@jamara.com
Web: www.jamara.com

PenTec s.r.o. (Czech Republic & Slovakia Distributor)

Veleslavínská 30/19
CZ-162 00 Praha 6, Czech Republic
Tel: +420 235 364 664
Mobil: +420 739 075 380
Mail: servis@topdrony.cz
Web: www.topdrony.cz

Catalogue Request

Order the current catalogue with our complete assortment of modelling goods today. Please send the catalogue to the following specialist dealer:

Your dealer:

We will include a catalogue for your attention with the next order placed by your dealer.