SCX 2.4 GHz Transmitter | Receiver System

General Information and Safety

General Remarks: Jamara e.K. is not liable for any damage caused to the product or by it, due to improper operation or handling errors. The customer alone bears the full responsibility for the proper use and handling, including assembly, charging, and operation of the model, and selection of the operating area. Please refer to the operating and user instructions, which contain important information and warnings.

Declaration of Conformity: Jamara e.K. declares that the model "SCX 2.4 GHz, No. 061172" complies with Directive 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.jamara-shop.com/Conformity.

Warning: This is a model building product - Not a toy! Read the complete instructions and security instructions carefully before using the model. Please fully and carefully read warnings/safety instructions. These are for your own security and can avoid accidents/injuries.

Box Contents and Specifications

Box Contents:

• Transmitter
• Receiver
• Instruction Manual

Recommended Accessories:

• 8 x AA Batteries (Ord. No. 140267, 4 pcs)

Features:

• 2 Channel 2.4 GHz Transmitter
• 3 Channel 2.4 GHz Receiver
• 2 Servo Reverse switches
• 2 Trim Sliders
• Charging socket
• Programmable fail-safe on the receiver

Technical Data - Transmitter:

Technical Data - Receiver (SCX 2.4 GHz, Ord.No. 061171):

Safety Precautions and Operation

Operating Precautions:

• Before switching on the receiver, ensure the throttle stick is in the 'Off' position.
• Ensure the transmitter and receiver are compatible and bonded to one another.
• Always switch the transmitter on first, then the receiver.
• Always switch the receiver off first, then the transmitter.
• Complete a full range and function test before every operation.
• Never fly over people and do not allow your model to endanger people or animals.
• Do not fly near to over-head cables, buildings or airfields.
• The system must not be operated in rain, or thunder storms.
• If you do not intend to use the transmitter for a long period, remove the batteries.

Transmitter Layout Description:

The transmitter features the following controls and indicators:

• 1. Antenna: Transmits the radio signal.
• 2. Handle: Ergonomic grip for the user.
• 3. Power LED: Indicates the transmitter's power status.
• 4. Servo Reverse CH1: Switch to reverse the direction of Channel 1 servo.
• 5. Left/Right Stick: Controls steering or primary function.
• 6. Left/Right Trim: Fine-tunes the neutral position for steering or primary function.
• 7. Binding Button: Used for synchronizing the transmitter with the receiver.
• 8. ON/OFF Switch: Powers the transmitter on and off.
• 9. Throttle Stick: Controls acceleration and braking/reverse.
• 10. Throttle Trim: Fine-tunes the neutral position for throttle.
• 11. Servo Reverse CH2: Switch to reverse the direction of Channel 2 servo.
• 12. Indicator LED: Provides status information for the transmitter.

Battery Hatch: Located on the rear of the transmitter. To open, push down on the marked 'Push' area and slide the cover. Ensure correct battery polarity when inserting batteries.

Receiver Description:

The receiver allows direct connection of two servos. It has the following channel allocation:

• Channel 1: Steering
• Channel 2: Throttle
• Binding Channel 3: Used with the binding cable for synchronization.

Binding Procedure (Synchronization):

The transmitter and receiver must be bound together for the system to function. Follow these steps:

1. Fit the binding plug to socket 3 on the receiver and connect the power supply. The receiver LED will begin to blink.
2. Press and hold the binding button on the transmitter, then switch the transmitter on. The transmitter enters binding mode.
3. Once binding is complete, the receiver LED will shine steadily.
4. Switch off the transmitter and receiver.
5. Remove the binding plug.

Important Information: The system will not function while the binding button is pressed. Do not leave the system in binding mode for extended periods.

Settings:

Before operating your model, carefully check that the servos operate in the correct direction. If they do not rotate in the correct direction, use the servo reverse switches located on the front of the transmitter to change the direction. The servo neutral positions should then be set by moving the servo arms until they are at exactly 90° with the trim central. The trim should only be used to make fine adjustments when operating the model. If you are using this system with an Internal Combustion engine, make sure that the linkage cannot bind in either the full throttle or tick-over positions.

Switching On Sequence:

1. Connect all of the components together.
2. Switch on the transmitter.
3. Connect the power supply to the receiver and switch on if required.
4. Check that all of the LEDs are correctly illuminated.
5. The system is now switched on and ready to operate.

Switching Off Sequence:

1. Switch off and unplug the receiver power supply.
2. Switch off the transmitter.

Model Operation:

Steering:

This function is used to steer the model in the correct direction. Moving the steering stick to the left or right will make the wheels, or hull if operating a boat, move in that direction. Moving the stick to the left should make the model steer to the left.

Throttle:

This function is used to make the model move forward or in reverse and it also is used to control the model's speed. Pushing the stick forwards makes the model accelerate forwards and pulling it to the rear will make the model brake first and then to accelerate in reverse.

Recycling and Service Information

Disposal Restrictions:

Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. You are obliged to take out the batteries, if possible, and to dispose of the electrical equipment at the communal collection points. Should personal data be stored on the electrical appliance you must remove them by yourself.

Service Centers:

Germany:

• Reitter Modellbau Versand
  Patricia Reitter
  Degerfeldstrasse 11
  72461 Albstadt
  Tel: 07432 9802700
  Fax: 07432 2009594
  Mail: info@modellbauversand.de
  Web: www.modellbauversand.de
• Bay-Tec
  Martin Schaaf
  Am Bahndamm 6
  86650 Wemding
  Tel: 07151 5002192
  Fax: 07151 5002193
  Mail: info@bay-tec.de
  Web: www.bay-tec.de
• Modellbau Zentral
  Peter Hofer
  Bresteneggstrasse 2
  CH-6460 Altdorf
  Tel: +41 79 429 62 25
  Mobil: +41 41 870 02 13
  Mail: info@modellbau-zentral.ch
  Web: www.modellbau-zentral.ch

European Union / International:

• JAMARA e.K.
  Manuel Natterer
  Am Lauerbühl 5
  DE-88317 Aichstetten
  Tel: +49 (0) 75 65/94 12-0
  Fax: +49 (0) 75 65/94 12-23
  Mail: info@jamara.com
  Web: www.jamara.com

Czech Republic and Slovakia Distributor:

• PenTec s.r.o.
  Veleslavínská 30/19
  CZ-162 00 Praha 6
  Tel: +420 235 364 664
  Mobil: +420 739 075 380
  Mail: servis@topdrony.cz
  Web: www.topdrony.cz

Order Catalogue

Request the latest Jamara catalogue with their complete assortment of modelling goods today.

Image of a coupon/order form with fields for customer details and dealer information, featuring the Jamara logo and 'Modellbau aktuell' text.

Customer Details:

Name: _______________________________

First Name: _______________________________

Street: _______________________________

City: _______________________________

Phone: _______________________________

E-mail: _______________________________

Send Catalogue To Dealer:

Your Dealer: _______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

The catalogue will be included with your dealer's next order.