V-TUF HDC140-110V High-Pressure Washer

⚠️ Please read this manual before using the HDC140-110V.

Product Components and Assembly

[Diagram illustrating the unpacking of the pressure washer from its box.]

[Diagram showing the assembly of the handle (C3) onto the main unit (H).]

[Diagram showing the main V-TUF HDC140-110V pressure washer unit.]

[Diagram of the operator manual (MANUALE) and other documentation (A1-A4).]

[Diagram showing the high-pressure hose (B5), gun (B3), and lance assembly.]

[Diagram showing a set of different colored spray nozzles and a foam cannon.]

[Symbol for professional use (E2)] [Symbol for domestic use (E1)]

Assembly Steps:

1. [Diagram showing handle (C3) being attached to the main unit (H) using screws (C10).
2. [Diagram showing the oil cap (B7) being unscrewed and replaced with a pressure release cap.]
3. [Diagram showing the adapter (C9) being connected to the water inlet, with a filter shown.]
4. [Diagram showing the high-pressure hose (B5) being connected to the unit.]

Controls and Operation

[Diagram showing a person using the pressure washer, with water jet directed away from the unit.]

[Diagram showing the starter device (H) in OFF (0) and ON (I) positions.]

[Diagram showing the water jet control lever (I) being engaged and disengaged with the safety catch (D).]

[Sequence showing trigger release and engagement with safety catch (D), illustrating the operation of the Total Stop System (TSS) if applicable.]

Electrical Connection and Water Supply

[Diagram illustrating electrical connection, possibly attaching a plug or cable.]

[Diagram showing a person using the pressure washer with a hose.]

[Diagram of the assembled pressure washer.]

[Diagram showing the nozzle cleaning tool (C1) being used on a nozzle.]

[Diagram showing a hand holding a part labeled M, possibly for unjamming the motor.]

Electrical Cable Specifications:

[Electrical schematic for 230V 1~ connection.]

[Electrical schematic for 400V 3~ connection.]

Water Supply Connection:

Place the appliance as close to the water supply system as possible.

• Water outlet (OUTLET)
• Water inlet with filter (INLET)

Connection to the mains water supply: The appliance may only be connected directly to the mains drinking water supply if the supply hose is fitted with a backflow preventer valve as per current regulations in force. Ensure the hose is at least Ø 13 mm, reinforced, and not more than 25 m long.

Suction of water from open containers:

1. Screw the inlet hose with filter to the water INLET and insert it down to the bottom of the container.
2. Vent the air from the appliance: a) Unscrew the lance. b) Start the appliance and keep the gun open until there are no air bubbles in the water flowing out.
3. Switch the appliance off and screw the lance back on.

N.B.: The maximum suction height is 0.5 m. The suction hose should be filled before use.

Safety Instructions and Signs

1.1 General: This technologically advanced product is designed by leading European manufacturers. Read this booklet carefully and follow instructions for best performance and safety. Take all possible precautions to protect yourself and others.

2.1 Safety Signs: Comply with instructions provided by safety signs fitted to the appliance and in this manual. Check that symbols and signs are present and legible.

• ⚠️ Warning - Caution - Hazard
• ℹ️ Please read these instructions carefully before use.
• [Symbol for professional use (E2)]: Indicates intended for professional use by experienced individuals. Not for children or persons with impaired physical, sensory, or mental capabilities without necessary experience or supervision.
• [Symbol for domestic use (E3)]: Indicates intended for non-professional (domestic) use. May be used by persons with impaired capabilities if supervised or instructed and aware of risks.
• [Symbol for moving parts]: Do not touch.

Symbol Explanations:

• 0: Switch "OFF" position
• I: Switch "ON" position
• [Sound Power Level symbol]: Guaranteed sound power level.
• [Prohibition symbol for drinking water connection]: Informs users that local regulations may prohibit connection to the drinking water supply system.
• ⚠️ [Danger sign]: Warns users not to direct the water jet at people, animals, electrical equipment, or the product itself.
• [Insulation Class II symbol]: This product is rated in insulation class II, meaning it has reinforced or double insulation.
• [Insulation Class I symbol]: This product is rated in insulation class I, meaning it is equipped with a protective earthing conductor.
• [CE Mark]: The product complies with the relevant European directives.
• [Symbol for WEEE disposal (E1)]: Indicates the appliance must not be disposed of as municipal waste; it may be handed in to the dealer on purchase of a new appliance. Electrical and electronic parts must not be reused for improper uses as they contain substances that constitute health hazards.

Personal Protective Equipment (PPE):

• [Ear Defenders symbol]: Wear ear defenders.
• [Protective Mask symbol]: Wear a protective mask.
• [Protective Gloves symbol]: Wear protective gloves.
• [Safety Footwear symbol]: Wear safety footwear.
• [Protective Clothing symbol]: Wear protective clothing.

Safety Rules and Residual Risks

3.1 Safety "DO NOTS":

• DO NOT allow children to use the appliance; supervise them.
• High pressure jets may be dangerous if incorrectly used.
• DO NOT use with flammable or toxic liquids, or incompatible products. Use in potentially inflammable or explosive atmospheres is forbidden.
• RISK OF EXPLOSION: DO NOT use to spray flammable liquids.
• DO NOT point the water jet at people or animals.
• DO NOT point the water jet at the unit itself, electrical parts, or other electrical equipment.
• DO NOT use with people within its range of action unless they are wearing protective clothing.
• DO NOT point the jet at yourself or others to clean clothing or footwear.
• DO NOT use the appliance outdoors when it is raining.
• DO NOT allow children, incompetent persons, or those who have not read and understood the instructions to use the appliance.
• DO NOT touch the plug and/or socket with wet hands.
• DO NOT use if the electric cable is damaged. It must be replaced by the manufacturer, an authorized service center, or similarly qualified persons.
• DO NOT use if a supply cable or important parts like safety devices, high pressure hoses, or gun are damaged.
• DO NOT jam the trigger in the operating position.
• Check that the data plate is affixed to the appliance; if not, inform your dealer. Appliances without plates must NOT be used.
• DO NOT tamper with or adjust the setting of the safety valve or safety devices.
• DO NOT alter the original diameter of the spray head nozzle.
• DO NOT move the appliance by pulling on the ELECTRIC CABLE.
• DO NOT allow vehicles to drive over the high pressure hose.
• DO NOT move the appliance by pulling on the high pressure hose.
• When directed towards tyres, tyre valves, or other pressurised components, the high pressure jet is potentially dangerous. Do not use the rotating nozzle kit and always keep the jet at a distance of at least 30 cm.
• The use of non-original accessories and spare parts is prohibited. All modifications are prohibited and will void the Declaration of Conformity and relieve the manufacturer of liability.

3.2 Safety "MUSTS":

• All electrical conductors MUST BE PROTECTED against the water jet.
• The electric supply connection must be made by a qualified electrician and comply with IEC 60364-1. A residual current device (RCD) cutting off power if leakage current exceeds 30 mA for 30 ms, or a ground fault interrupt device, must be installed.
• During start-up, the appliance may cause network noise.
• Use of a residual current breaker (RCB) will provide additional protection for the operator (30 mA).
• Models supplied without a plug must be installed by qualified staff.
• Use only approved electrical extension leads with suitable conductor cross-section.
• Always turn off the switch when leaving the appliance unattended.
• ⚠️ High pressure may cause parts to rebound: wear all the protective clothing (PPE) and equipment needed to ensure the operator's safety.
• Before doing work on the appliance, REMOVE the plug.
• Before pressing the trigger, GRIP the gun firmly to counteract the recoil.
• COMPLY WITH local water supply authority regulations. Under IEC 60335-2-79, the appliance may only be connected to the mains drinking water supply if the supply hose is fitted with a backflow preventer valve with drain facility corresponding to EN 12729 type BA. The backflow preventer can be ordered from the manufacturer.
• Water that has passed through backflow preventers is considered to be non-potable.
• Maintenance and/or repair of electrical components MUST be carried out by qualified staff.
• DISCHARGE residual pressure before disconnecting the hose from the appliance.
• CHECK before each use and at regular intervals that screws are fully tightened and that there are no broken or worn parts.
• ONLY USE detergents which will not corrode the coating materials of the high pressure hose / electric cable.
• ENSURE that all people or animals keep a minimum distance of 16 yd. (15m) away.
• This appliance is designed for use with the detergent supplied or recommended by the manufacturer. The use of other detergents or chemicals may adversely affect the appliance's safety.
• Do not allow detergent to come into contact with skin, especially eyes! In case of contact with eyes, rinse with plenty of water and seek medical advice at once!
• High pressure hoses, fittings, and joints are important for the appliance's safety. Use only manufacturer-recommended parts.
• To ensure the appliance's safety, only use the manufacturer's genuine parts, or other parts which carry its approval.
• Unsuitable extension cables can be dangerous. If an extension cable is used, it must be suitable for outdoor use, and the connection must be kept dry and off the ground. Use of a power cable reel which keeps the socket at least 60 mm above the ground is strongly recommended.
• Switch the appliance off and disconnect it from the power supply before assembly, cleaning, adjustments, maintenance, storage, and transportation.
• Insert the pipe jet kit down to the red mark before turning the appliance on.

General Information

4.1 Use of the manual: This manual is an integral part of the appliance and should be kept for future reference. Read it carefully before installing/using the unit. If the appliance is sold, pass this manual to the new owner.

4.2 Delivery: The appliance is delivered partially assembled in a cardboard box. The supply package is illustrated in fig.1.

• 4.2.1 Documentation supplied: A1 Use and maintenance manual, A2 Safety instructions, A3 Declaration of conformity, A4 Warranty regulations.

4.3 Disposing of packaging: Packaging materials are not environmental pollutants but must be recycled or disposed of in compliance with relevant legislation.

Technical Information

5.1 Envisaged use: Designed for individual use for cleaning vehicles, machines, boats, masonry, etc., to remove stubborn dirt using clean water and biodegradable chemical detergents. Vehicle engines may be washed only if dirty water is disposed of as per regulations.

• Intake water temperature: see data plate on the appliance.
• Intake water pressure: min. 0.1 MPa - max. 1 MPa.
• Operating ambient temperature: above 0°C.

The appliance is compliant with IEC 60335-1 and IEC 60335-2-79 standards.

5.2 Operator: [Symbol illustrated in fig. 1 identifies the appliance's intended operator (professional or non-professional).]

5.3 Main components:

• B2 Lance
• B3 Gun with safety catch
• B4 Electric cable with plug (on models with this feature)
• B5 High pressure hose
• B6 Detergent tank (on models with this feature)
• B7 Oil cap (on models with this feature)
• E Nozzle
• F Detergent regulator (on models with this feature)
• G Pressure regulator (on models with this feature)
• L Water filter

5.3.1 Accessories (if included):

• C1 Nozzle cleaning tool
• C2 Rotating nozzle kit
• C3 Handle
• C4 Brush
• C5 Hose reel
• C6 Water suction kit
• C7 Pipe jet kit
• C8 Large surface cleaning brush kit
• C9 Adapter
• C10 Screws
• C11 Brackets
• C12 Lever
• C13 Detergent kit
• C14 Wheels
• C15 Lubricating grease tube

5.4 Safety devices:

• Starter device (H): Prevents accidental use.
• ⚠️ Warning - danger! Do not tamper with or adjust the safety valve setting.
• Safety valve and/or pressure limiting valve: When the gun trigger is released, the valve opens and water recirculates through the pump inlet or is discharged onto the ground.
• Thermostat valve (D1 where fitted): If water temperature exceeds set limits, it discharges hot water and draws in cold water to restore correct temperature.
• Safety catch (D): Prevents accidental spraying of water.
• Overload cutout: Stops the appliance in case of overload.

Installation

6.1 Assembly: ⚠️ Warning - danger! All installation and assembly operations must be performed with the appliance disconnected from the mains power supply. The assembly sequence is illustrated in fig.2.

6.2 Fitting the pressure release caps: To prevent oil leaks, the appliance is delivered with oil intakes sealed with red caps, which must be replaced with the pressure release caps supplied.

6.3 Fitting the rotating nozzle: The rotating nozzle kit delivers greater washing power. Use may cause a pressure reduction of 25% compared to the adjustable nozzle, but offers greater washing power due to rotation.

6.4 Electrical connection: ⚠️ Warning - danger! Check that the electrical supply voltage and frequency (V-Hz) correspond to those specified on the data plate (fig.2).

• 6.4.1 Use of extension cables: Use cables and plugs with "IPX5" protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See table 1.

6.5 Water supply connection: ⚠️ Warning - danger! Only clean or filtered water should be supplied. The flow rate of the water inlet tap should be equal to the pump flow rate. Place the appliance as close to the water supply system as possible.

• 6.5.1 Connection points: Water outlet (OUTLET), Water inlet with filter (INLET).
• 6.5.2 Connection to the mains water supply: As described in the "Electrical Cable Specifications" section.
• 6.5.3 Suction of water from open containers: As described in the "Electrical Cable Specifications" section.

Adjustments

7.1 Adjusting the spray nozzle: Water flow is adjusted by regulating the nozzle (E).

7.2 Adjusting the detergent: To deliver detergent at the correct pressure, set the nozzle (E) (where fitted) on " " or fit the detergent kit (C13) (where available). The quantity of detergent delivered is adjusted using the regulator (F).

7.3 Adjusting the working pressure: The regulator (G) is used to adjust the working pressure. The pressure is shown on the pressure gauge (where fitted).

Information on Use

8.1 Controls:

• Starter device (H): Set to ON/I to start the motor (or ready to start for TSS models). Set to OFF/0 to stop. A pilot light may indicate status.
• Water jet control lever (I): Activates the water jet.

⚠️ Warning - danger! During operation, the appliance must be positioned on a firm, stable surface.

8.2 Start-up:

1. Turn on the water supply tap fully.
2. Release the safety catch (D).
3. Depress the gun trigger for a few seconds and start up the appliance using the starter device (ON/I).

⚠️ Warning - danger! Before starting, check that the appliance is receiving water correctly; use without water will damage it. Do not cover ventilation grilles when in use.

TSS models: With automatic delivery flow cut-off: trigger release automatically cuts out the motor; trigger depression restarts the motor. Operations must be at least 4-5 seconds apart.

To prevent damage, do not allow the appliance to operate dry. For models without TSS, do not cut off the jet of water for more than 5 minutes with the appliance running to prevent overheating.

8.3 Stopping:

1. Set the starter device switch to OFF/0.
2. Depress the gun trigger to discharge residual pressure.
3. Engage the safety catch (D).

8.4 Restarting:

1. Release the safety catch (D).
2. Depress the gun trigger to discharge residual air.
3. Set the starter device to ON/Ι.

8.5 Storage:

1. Turn off the water supply tap.
2. Discharge residual pressure from the gun.
3. Switch the appliance off (OFF/0).
4. Remove the plug from the socket.
5. Drain and wash out the detergent tank with clean water.
6. Engage the gun safety catch (D).

8.6 Refilling and using detergent: Use accessories and procedures described in point 7.3. Using a hose longer than originally supplied may reduce or halt detergent suction. Fill the tank (B6) with highly biodegradable detergent.

8.7 Recommended cleaning procedure: Apply detergent mixed with water to the dry surface. For vertical surfaces, work from bottom upwards. Leave detergent for 1-2 minutes, but do not let the surface dry. Rinse from the bottom upwards with the high pressure jet at a minimum distance of 30 cm. Do not let rinse water run onto unwashed surfaces. Scrubbing with brushes may be needed. High pressure may damage some surfaces; avoid using the finest adjustable nozzle or rotating nozzle on delicate or painted parts, or pressurised components (e.g., tyres).

Maintenance

Any maintenance not covered here should be carried out by an Authorised Sales and Service Centre.

⚠️ Warning - danger! Always disconnect the plug from the power socket before carrying out any work on the appliance.

• 9.1 Cleaning the nozzle: Disconnect the lance from the nozzle. Remove dirt deposits using the tool (C1).
• 9.2 Cleaning the filter: Inspect the inlet filter (L) and detergent filter (if fitted) before each use and clean if necessary.
• 9.3 Unjamming the motor: In case of lengthy stoppages, turn the drive shaft with a tool (M) to unjam the motor.
• 9.4 Refilling the oil: Add oil through the intake hole to restore the correct level. Refer to "Oil characteristics" table for details.
• 9.5 End-of-season storage: Treat the appliance with non-corrosive, non-toxic antifreeze. Store in a dry place, protected from frost.

10 Storage and Transportation: Store accessories as shown in fig. 5. Transport the machine as shown in fig. 5.

Troubleshooting

(*) If the motor stops and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (Overload cutout has been tripped). If the problem recurs more than once, contact your nearest Authorised Service Centre.

[Plate showing MODEL, SERIAL NUMBER, and technical specifications like voltage, frequency, power, flow rate, pressure, and distributor information.]

How to Avoid Damaging Surfaces

⚠️ WARNING

• Using the appliance to wash tyres may damage the tyre and can be dangerous.
• Never point the high pressure jet straight at the tyre.
• Always use the appliance at the lowest pressure setting when cleaning in the vicinity of wheels and tyres.
• Never use the "Turbo Lance" for washing any part of the vehicle.
• For further information refer to section: "8.7 Recommended cleaning procedure".

Technical Data

Subject to technical modification!

Warranty

The validity of the warranty is in accordance with the relevant legislation in the country where the product is sold. The warranty covers materials, construction, and conformity defects during the warranty period. The manufacturer will replace defective parts and repair the product if not excessively worn, or replace it.

The warranty does not cover components subject to normal wear and tear (valve, piston, water gasket, oil gasket, springs, O-rings, accessories such as the hose, gun, brushes, wheels, etc.).

The warranty does not cover defects caused by or arising from:

• Improper use, misuse, negligence.
• Hire or professional use if the product has been sold for domestic use.
• Failure to comply with the maintenance instructions provided in this manual.
• Repair by unauthorized staff or centers.
• Use of non-genuine parts or accessories.
• Damage caused by transport, by dirt or foreign bodies, accidents, storage, or warehousing problems.

Proof of purchase must be submitted to obtain warranty cover.

For assistance, contact the point of sale where your appliance was purchased.

www.V-TUF.COM