Hama WiFi Door/Window Contact

Model: 00176553

Controls and Displays

A: Device

1 Battery compartment closure: A cover or flap for accessing the batteries.
2 LED: An indicator light.
3 Pairing button: A button used for device pairing/setup.
4 Tamper protection: A mechanism that detects if the device casing is opened.

B: Sensor

5 Magnetic contacts: Two parts that, when aligned, indicate the status of the door or window.

Introduction and Important Notes

Thank you for choosing a Hama product. Please take your time to read the following instructions and information completely. Keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

⚠️ Warning: This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

ℹ️ Note: This symbol is used to indicate additional information or important notes.

Package Contents

1x WiFi door / window contact
2 x AAA batteries
1 x adhesive strip set
4x screws

Safety Instructions

The product is intended for private, non-commercial use only.

Protect the product from dirt, moisture, and overheating; use it in dry environments only.
If operated outdoors, it may only be used in protected outdoor areas.
Do not attempt to service or repair the product yourself. Leave all service work to qualified experts.
Do not continue to operate the product if it is visibly damaged.
As with all electrical products, keep this device out of the reach of children.
Use the product only for the intended purpose.
Do not use the product near heaters, other heat sources, or in direct sunlight.
Do not use the product in areas where electronic products are not permitted.
Do not drop the product or expose it to major shocks.
Do not modify the product in any way, as this voids the warranty.
Keep packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately according to locally applicable regulations.
Do not operate the product outside the specified power limits.
Do not open the device or continue to operate it if it becomes damaged.
Only use the article under moderate climatic conditions.

Battery Warnings

When inserting batteries, note the correct polarity (+ and - markings) and insert accordingly. Failure to do so could result in leakage or explosion.
Only use batteries (or rechargeable batteries) that match the specified type.
Before inserting batteries, clean the battery contacts and polarity contacts.
Do not allow children to change batteries without supervision.
Do not mix old and new batteries, or batteries of different types or manufacturers.
Remove batteries from products not being used for extended periods (unless kept ready for emergency).
Do not short-circuit batteries.
Do not charge batteries.
Do not burn batteries.
Keep batteries out of the reach of children.
Never open, damage, or swallow batteries, or allow them to enter the environment, as they can contain toxic, environmentally harmful heavy metals.
Remove spent batteries from the product and dispose of them without delay.
Avoid storing, charging, and using in extreme temperatures and at extremely low atmospheric pressures (e.g., at high altitudes).

Product Characteristics and Getting Started

This WiFi door/window contact monitors (sends push messages to a smartphone upon triggering) and checks the status of windows or doors (open/closed).

The following voice command can be used:

Status check: "Alexa/OK Google, is my window / door open / closed?"

Inserting / Changing Batteries

Press the button on the top of the larger sensor and remove the cover on the back.

Remove spent batteries and dispose of them if required. Insert two new batteries of type AAA, ensuring correct polarity as shown in the diagram in the battery compartment.

Close the battery compartment by reattaching the cover to the rear of the larger sensor.

Diagram shows how to open the battery compartment by pressing a button on the top of the larger sensor and sliding off the back cover. It also illustrates inserting two AAA batteries, emphasizing correct polarity (+ and - markings).

Installation

⚠️ Warning:

Before mounting, check that the chosen wall is suitable for the weight. Ensure no electric, water, gas, or other lines run through the wall at the mounting site.
Do not mount the product above locations where persons might sit or stand.
It is recommended to attach the sensor to the window or door frame and secure the device directly to the window/door.
Ensure that the markings (triangles) on the device and sensor are aligned in a straight line and are no more than 10 mm apart when the door/window is closed.

Diagram shows the device and sensor mounted on a door and frame. It highlights that alignment marks (triangles) on both parts should be in a straight line and the gap between contacts should be a maximum of 10 mm when the door/window is closed. Visual indicators show correct (✔️) and incorrect (❌) alignment/gap.

You can either screw the device and sensor in place or use adhesive pads.

Diagram illustrates two mounting methods: securing with screws (showing screw holes) and attaching with adhesive pads.

If a door leaf or window juts out, the sensor can also be attached to the side, and the device secured flat to the frame.

Diagram shows an alternative mounting scenario where the sensor is attached to the side of a protruding door leaf or window, with the main device mounted flat on the frame.

Integrating Devices into the Hama Smart Home (Solution)

Insert the two supplied AAA batteries, observing the correct polarity. When activating the burglar alarm, the LED should briefly light up blue; otherwise, replace the batteries.

Press the pairing button for 5 seconds. The LED starts to flash red quickly. If it flashes slowly, press the button again for 5 seconds.
Open the app and sign in.
Press the ➕ icon in the top right-hand corner to add a new device.

Diagrams show screenshots of the Hama Smart Home app: 'My Home' screen, adding a new device (+ icon), 'Connecting Now' screen, and 'Added successfully' screen with a checkmark.

Warning - Installation with Adhesive:

All parts are suitable only for indoor use. Do not install outdoors.
Ensure the mounting surface is free from dust and grease. Use a suitable cleaner from a specialist retailer.
The adhesive pads are intended to be permanent. Carefully pull the adhesive pad off the mounting surface to remove it.
Environmental influences (e.g., humidity, sunlight, cold) can impair the long-term stickiness of the adhesive pads.
Possible residue on the mounting surface after removal of the adhesive pads cannot be ruled out.

Once the connection is successful, the LED stops flashing quickly, and the app confirms the sensor is connected. You can assign it a different name if desired.

Click 'Finish' to complete the process. You can now attach and configure the sensor.

ℹ️ Note: A detailed description of the Hama Smart Home (Solution) App and its full scope of functions can be found in our App Guide at: www.hama.com ⇨ Article Number ⇨ Downloads ⇨ App Operating Instructions.

Technical Data

Specification	Value
Voltage supply	2 x AAA batteries, 3V
Frequency band/ frequency bands	2.4 GHz

Care and Maintenance

ℹ️ Note: Disconnect the device from the mains before cleaning and during prolonged periods of non-use.

Clean this product only with a slightly damp, lint-free cloth. Do not use aggressive cleaning products.
Ensure that no water is able to enter the product.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the operating instructions and/or safety notes.

Recycling Information

ℹ️ Note on environmental protection: Following the implementation of European Directives 2012/19/EU and 2006/66/EU into national legal systems, the following applies:

Electrical and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers are legally obliged to return electrical and electronic devices, as well as batteries, to designated public collection points or to the point of sale at the end of their service lives. Detailed information on this topic is defined in the national laws of the respective country. The symbol on the product, operating instructions, or package indicates that the product is subject to these regulations. By recycling, reusing materials, or other forms of utilizing old devices/batteries, you are making an important contribution to protecting our environment.

Declaration of Conformity

Hama GmbH & Co KG hereby declares that the radio equipment type [00176553] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hama.com ⇨ 00176553 ⇨ Downloads.

	Hama WiFi Door/Window Contact - User Manual and Safety Information Comprehensive user manual for the Hama WiFi Door/Window Contact, detailing setup, operation, safety precautions, battery handling, warranty, recycling, and conformity declarations. Supports multiple languages.
	Hama Window-Door-Sensor 00176663 Operating Instructions This document provides operating instructions for the Hama Window-Door-Sensor (00176663). It covers introduction, safety guidelines, installation of the Hama Smart Home app, device integration, setting options, technical data, care, warranty, and support.
	Hama WINDOW-DOOR-SENSOR: Safety Instructions, Specifications, and User Guide Comprehensive safety instructions, technical specifications, and user guidance for the Hama WINDOW-DOOR-SENSOR (Model 00176663). This document covers proper usage, battery handling, warranty information, and compliance details.
	Hama Smart Water Sensor Operating Instructions and Manual Operating instructions and technical manual for the Hama Smart Water Sensor (00176668). Learn about installation, setup, app integration, features, safety, and technical specifications.
	Hama Smart Home App Guide: Setup, Scenes, Automations, and Integrations A comprehensive guide to the Hama Smart Home application, covering device setup, creating smart scenes and automations, grouping devices, and integrating with Amazon Alexa and Google Home. Learn troubleshooting tips for network connectivity and device status.
	Hama Smart Garage Door Controller Manual and Safety Instructions Comprehensive guide to the Hama Smart Garage Door Controller, including safety instructions, technical specifications, and conformity declarations. Learn how to safely install and use your smart garage door opener.
	Hama WiFi Upgrade Switch (176556) - Installation and Operating Manual Comprehensive guide for the Hama WiFi Upgrade Switch (176556), covering installation, setup, safety precautions, technical specifications, and app integration for smart home control.
	Hama Smart Garage Door Controller Operating Instructions Operating instructions for the Hama Smart Garage Door Controller, including setup, configuration, and safety information.