GoHawk RE8/RE9-X Powersports Amplified Soundbar User Manual & Installation Guide

Product Description

The GoHawk RE8 and RE9-X are Powersports Amplified Soundbars designed for ATVs, UTVs, motorcycles, and other recreational vehicles. They offer an all-in-one audio solution with built-in amplifier, Bluetooth 4.2 connectivity, 3.5mm AUX input, and an integrated FM radio receiver.

Key Features

• All-In-One design with a Built-in Amplifier
• White LED strip light with 2 brightness settings
• Built-In Bluetooth 4.2 for Audio Streaming
• 3.5mm AUX Input Jack
• Support USB drive with MP3 music files
• Built-In FM Radio Receiver

Before Installation

Safety Precautions:

• Do not install components or wiring near moving parts, ignition parts, fuel lines, the engine, or hot exhaust.
• Ensure speakers do not obstruct vehicle safety features like lights, horns, or brake levers.
• Always test the speakers/amplifier before final installation by connecting to the battery and playing music for at least 3 minutes.
• Cutting rubber inserts may be required for certain handlebar sizes.
• Splash, water, and dust resistance are not permanent and may decrease with normal wear.
• Confirm wiring before powering on the unit.
• Ensure speakers are tightly clamped to the handlebar.
• Disconnect the speaker from the battery if the vehicle will be non-operational for more than 15 days to prevent battery drain.
• Note that engine, pipe, and wind noise can overpower speaker volume at certain speeds due to physics.

Installation Guide

Wiring Diagram

A wiring diagram illustrates the connections: The soundbar connects to a 12V Battery via a 59" Power Cord. The soundbar also has connections for a Bluetooth Antenna and an FM Radio Antenna. The power cord connects directly to the speaker.

Wiring Instructions

1. Connect the power cord to the speaker.
2. Connect the RED wire to the positive (+) terminal and the BLACK wire to the negative (-) terminal of a 12V battery.
3. Ensure the antenna wires (BLACK and BLUE) are placed in an open area for optimal reception.
4. Always connect to a correct power supply (DC 12V).

Mounting Instructions

The soundbar can be mounted using the provided clamps and ball joint bases.

1. Use four Phillips screws to attach the ball stub base to each side of the stereo unit.
2. Insert ring (A) into the base, then secure the ball seat (B) with the ball stub.
3. Turn ring (A) counter-clockwise to tighten the ball joint. Do not over-tighten to allow for swiveling.
4. Repeat steps 2 and 3 for the other side of the stereo.
5. Use the mounting clamps (+ and -) as a pair. Install the clamp onto the handlebar using two hex socket cap screws. Use the included black rubber insert around the bar; cutting may be necessary for specific bar sizes.
6. Once the stereo is mounted on the handlebar, connect it to a 12V battery, following the wiring diagram.
7. Ensure the BLACK and BLUE antenna wires are in an open area for better reception.

Operation Instructions

• On/Off: Short press the (MOD) button to power on. Long press (MOD) to power off.
• Switch Mode: Short press (MOD) to cycle through Radio, USB, AUX, and BT modes. The unit will skip unavailable modes (e.g., if USB is not inserted).
• Adjust Volume: Long press the (<< Vol-) or (>> Vol+) buttons.
• Change Track / Scan Radio:
  • In USB/Bluetooth mode: Short press (<< Vol-) or (>> Vol+) for previous/next track.
  • In Radio mode: Double-click ( >|| ) to auto-scan and save stations (P1, P2, etc.). Short press ( >|| ) to select saved stations.
• Pause/Mute: In USB/Bluetooth mode, short press ( >|| ) to pause music.
• LED Light: Long press ( >|| ) to turn on the LED. Long press again for 2nd brightness level. Long press a third time to turn off the LED.
• Clock Setting: Short press (CLK) to display the clock. Long press (CLK) while the clock is displayed until it blinks. Use (<< Vol-) or (>> Vol+) to change the hour. Short press (CLK) to switch to minute setting, then use (<< Vol-) or (>> Vol+) to change the minute.

FM/BT/USB/AUX Modes

• FM Radio: Double-click ( >|| ) to auto-scan and save stations. Short press ( >|| ) to select saved stations. Ensure the black antenna wire is in an open area for best reception.
• Bluetooth: Short press (MOD) to switch to "BT" mode. Enable Bluetooth on your phone and search for "RE8" or "RE9-X". The "BT" indicator will stop blinking upon successful pairing. A PIN code of "0000" may be required.
• USB: Insert a USB drive containing MP3, WMA, or WAV files for automatic playback. The USB drive must be FAT formatted and support up to 32GB.
• AUX-IN: Short press the (MOD) button to switch to AUX mode. Connect an external music player via the AUX jack.

Troubleshooting

• Unit not turning on:
  • Verify RED wire is connected to positive (+) and BLACK wire to negative (-).
  • Check the plug connection to the power cord extension for proper internal connector placement.
  • Ensure the battery provides at least 12V. Contact support if issues persist.
• Unable to pair Bluetooth device:
  • Ensure the Bluetooth antenna (blue wire) is in an open area.
  • Clear previously paired devices from your phone and restart it.
  • The speaker automatically connects to the last paired phone. Disconnect the previous phone before pairing a new one.
• Volume not loud enough:
  • Confirm both speakers are functioning.
  • Adjust speaker direction towards the listener.
  • Maximize volume on both the stereo unit and the music source device (phone, MP3 player).
  • For iPhone, enable "Late Night" EQ in Music settings. For Android, adjust equalizer settings in Sound Quality and Effects.
• Mounting clamp does not fit:
  • The clamp is designed for handlebar sizes up to 1-1/4" (31.75mm).
  • Custom mounting may be needed for different bar sizes. Contact support for assistance.

Specifications

Warranty

Register Your Product: Visit goldenhawkusa.com/warranty

1-Year Limited Parts Warranty:

Golden Hawk USA products purchased in the United States are warranted for one year from the purchase date against defects in materials and workmanship. Free parts will be provided for one year. Replacement is at the sole discretion of the selling dealer, potentially with a new or reconditioned unit. The customer is responsible for return freight charges.

For other countries, contact technical support with a copy of the original invoice, a letter detailing the problem, your daytime phone number, and return shipping address (no P.O. Box). Obtain an RA# before sending defective items.

This warranty excludes damage from abuse, neglect, incorrect wiring, water/physical damage, or unauthorized modifications. Liability for incidental damages is excluded. The original proof-of-purchase is required. Warranty replacements do not extend the original warranty period.

Product Support

Visit: goldenhawkusa.com/contact-us

Email: info@goldenhawkusa.com

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. No guarantee is made that interference will not occur in a specific installation. If interference occurs with radio or television reception (determinable by turning the equipment off and on), users are encouraged to try one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from the receiver's circuit. Consult a dealer or experienced radio/TV technician for assistance.

Caution: Unauthorized modifications by the manufacturer could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules under two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.