Yeelight Smart LED Strip Lights User Manual and Specifications

Product Overview

This document provides comprehensive information for Yeelight Smart LED Strip Lights, available in 5-meter (16.4ft), 10-meter (32.8ft), and 20-meter (65.6ft) lengths. The product package typically includes the lightstrip itself, a controller unit, a power cord, and a power adapter.

Included Components:

• Lightstrip (available in 5m/16.4ft, 10m/32.8ft, or 20m/65.6ft lengths)
• Controller
• Power Cord
• Power Adapter

Note: Illustrations of the product, accessories, and user interface within this manual are provided for reference purposes only. Actual product features and functions may vary due to ongoing product enhancements.

Installing Your Device

Before Installation

1. Carefully unpack the box and verify that all listed items are included.
2. Connect the strip light to power and confirm that it illuminates correctly.

Installation Steps

1. Prepare the mounting surface by wiping it clean and ensuring it is dry.
2. Adhere the strip light to the prepared surface, pressing firmly to ensure good adhesion.
3. Peel off the protective film from the control box and affix it to a suitable location. For optimal sound-reactive effects, place the control box near your music source.
4. Connect the power adapter and turn on the strip light to begin using it.

Device Resetting

To reset the Yeelight Smart LED Strip Light to its factory settings, press and hold the Power button on the controller for 5 seconds within one minute of powering on the device. The device will indicate a reset in progress by breathing blue light. A change to a rainbow streamer light signifies that the device has been successfully reset.

Important Note: A device reset is necessary when connecting the light strip to a new smartphone or network.

Pairing Your Device with Yeelight Fun App

1. Download and install the Yeelight Fun application from your device's app store.
2. Ensure the light strip is powered on and has been successfully reset.
3. Enable Bluetooth connectivity on your smartphone.
4. Launch the Yeelight Fun app and follow the on-screen instructions to complete the pairing process.

Description of Button Functions

The controller unit typically features buttons for managing the light strip's functions:

• Turn light on/off: A single press of the power button.
• Switch light modes: Press the designated button to cycle through various lighting effects and presets.
• Enter music mode: Press the button to activate the music synchronization feature, allowing the lights to react to audio.

Specifications

Matter-compatible smart home hubs:

• Apple: Apple HomePod mini, Apple HomePod (2nd generation), Apple TV 4K (2nd generation and 3rd generation WiFi + Ethernet 128GB model)
• Google: Nest Wifi Pro (Wi-Fi 6E), Nest Hub (2nd gen), Nest Hub Max
• Amazon: Echo (4th Gen)

Customer Service and Support

• Warranty: 12-Month Limited warranty
• Support: Lifetime Technical Support
• Email: support@yeelight.com
• Official website: https://en.yeelight.com

Warnings & Cautions

• This product is intended for indoor use only.
• Avoid using the lightstrip when it is covered or recessed into a surface.
• Do not bend the LED strip more than 90 degrees to prevent product damage.
• Do not attempt to open or cut the lightstrip.
• Do not connect parts of this lightstrip with components from other manufacturers' lightstrips.
• Interconnections must only be made using the supplied connectors.
• Ensure any open ends are properly sealed before use.
• Use the LED lightstrip exclusively with the provided LED driver.
• To prevent premature product failure, operate the product within an ambient temperature range of -10℃ to 25℃ (14 to 77℉).
• The product is not water-resistant; exercise caution during installation and use in potentially damp environments.
• Children should not install the strip light unsupervised.
• Always unroll the strip lights completely before powering them on.
• The light source in this luminaire is not replaceable. The entire luminaire must be replaced when the light source reaches its end of life.
• Under normal operating conditions, maintain a separation distance of at least 20cm between the device's antenna and the user's body.
• This lightstrip is designed for decorative purposes and is not suitable for general room illumination.
• The control gear is designed to be replaceable by the end-user.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is contingent upon adherence to the following two conditions: (1) This device must not cause harmful interference, and (2) this device must accept any interference received, including interference that could lead to undesired operation.

Caution: Any changes or modifications made to this unit that are not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, as per Part 15 of the FCC Rules. These limits are established to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation. If this equipment does cause harmful interference to radio or television reception, which can be identified by turning the equipment off and on, users are encouraged to attempt to correct the interference through one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit that is different from the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

To satisfy FCC & IC RF exposure requirements, a separation distance of 20 cm or more must be maintained between the antenna of this device and persons during operation. For compliance assurance, operations at distances closer than this are not recommended.

Due to local law regulations, versions intended for North America do not feature a region selection option.

Supplier's Declaration of Conformity

Product Description: Yeelight SMART LED Strip Lights

Model Numbers: YLYDD-0091, YLYDD-0092, YLYDD-0093

Trade Name: [Not specified in provided text]

Responsible Party in USA: Yeelight Technology LLC

Testing Laboratory: Intertek Testing Services (Shanghai FTZ) Co., Ltd.

Addendum to the Test Report: 2411B2330SHA-001

FCC ID: 2ABEU-YLYDD0091

(Declaration made on behalf of the Responsible Party under FCC Part 15 SDoC procedure)