White Top Adventures Installation Guide
Sprinter 170 High Roof Strata Roof Rack
SPRR170-J
Ensuring the proper assembly and secure attachment of all WTA products to your vehicle is of utmost importance. Failure to adhere to these guidelines may lead to automobile accidents, presenting a substantial risk of bodily harm or even fatality to yourself and others. As the owner, it is incumbent upon you to meticulously assemble and secure WTA products, conducting a thorough examination of the mounting points and attachments before use, and routinely checking for any indications of wear or damage.
To ensure optimal safety, White Top Adventures strongly recommends enlisting the services of a qualified installer for the installation of any aftermarket accessories on your vehicle. If you lack mechanical expertise or are unfamiliar with the installation procedures, it is crucial to have the product installed by a certified professional or individuals with the requisite skills. Remember, the responsibility rests with you, and it must be approached with seriousness to safeguard the well-being of all individuals involved.
Parts List
| Item No. | Part Number | Description | Qty. |
|---|---|---|---|
| 1 | Front section 170 driver | 1 | |
| 2 | 3060 | Crossbars 1352MM (EXTRUSION, 25x50, M6x1.0, HR, SPRINTER) | 8 |
| 3 | Front section 170 p | 1 | |
| 4 | Armor Plate Front Section | 1 | |
| 5 | Middle section 170 driver | 2 | |
| 6 | Middle section 170 p | 1 | |
| 7 | Armor plate middle section 170 | 2 | |
| 8 | Rear section 170 driver | 1 | |
| 9 | Rear section 170 p | 1 | |
| 10 | Armor Plate Rear Section 170 | 2 | |
| 11 | V4 Sptr | Fairing | 1 |
| 12 | "X" Brace | 2 | |
| 13 | M10 nut-rail anchor (slider for factory roof rail) | 16 | |
| 14 | M10-22 | 18-8 Stainless Steel Hex Head Screw | 16 |
| 15 | 18-8 Stainless Steel Washer | 16 | |
| 16 | 18-8 Stainless Steel Split Lock Washer | 16 | |
| 17 | M6 crossbar anchor | 6 | |
| 18 | M6-12 | 18-8 Stainless Steel Button Head Hex Drive Screws | 6 |
| 19 | Black-Oxide 18-8 Stainless Steel Washer | 6 | |
| 20 | 18-8 Stainless Steel Split Lock Washer | 32 | |
| 21 | Black-Oxide 18-8 Stainless Steel Washer | 74 | |
| 22 | M8-25 Button head | 18-8 Stainless Steel Button Head Hex Drive Screws | 32 |
| 23 | M8-20 Button head | 18-8 Stainless Steel Button Head Hex Drive Screws | 42 |
| 24 | M8 Nylock Nut | High-Strength Steel Nylon-Insert Locknuts | 42 |
Tools Required
- 10 mm Wrench
- 17 mm Wrench
- 4 mm Allen Wrench
- 5 mm Allen Wrench
Package Contents
The package includes the following components:
- Driver Front Rail (QTY-1)
- Driver Rear Rail (QTY-1)
- Driver Rear Rail (QTY-1)
- Passenger Front Rail (QTY-1)
- Fairing (QTY-1)
- Joint Plate (QTY-2)
- Crossbar (QTY-6)
Hardware Pack
The hardware pack contains:
- Rail Nut (QTY-16)
- M10-22 Hexgon Head Screw (QTY-16)
- M6-12 Hexgon Socket Button Head Screw (QTY-8)
- M8-20 Hexgon Socket Button Head Screw (QTY-42)
- T-Block (QTY-8)
- M10 Spring Lock Washer (QTY-16)
- M8 Spring Lock Washer (QTY-32)
- M8-25 Hexgon Socket Button Head Screw (QTY-32)
- M8 Lock Nut (QTY-42)
- M10 Washer (QTY-16)
- M8 Washer (QTY-116)
- M6 Washer (QTY-8)
Installation Steps
- Slide half of the rail nuts into the passenger side factory roof rail, and half of them into the driver side rail.
- Space out the rail nuts close to the final position (groups of 2). Refer to Figure 1 for rough reference dimensions.
- Start loosely attaching the side rails to the roof rails using the M10-22 Hexgon Head Screw, M10 Spring Lock Washers, and M10 Washers. Do not tighten fully yet. Note: The front "foot" of the rack should be as far forward in the roof rail as it can go.
- Place your crossbars in the desired location, loosely bolting the M8-20 Hexgon Head Screws, M8 Spring Lock Washers, and M8 Washers in place.
- Note for Fairing Installation: If installing the front fairing, it is suggested to bolt the fairing to the crossbar first (see Figure 5), then attach that assembly to the roof rack (see Figure 6).
- Tighten all crossbar bolts using the 10 mm wrench. Note: Do not overtighten. If concerned about bolts backing out, a dab of blue Loctite can be applied before tightening completely.
- Now tighten side rails to the roof rail using the 17 mm wrench.
Important Safety Information
Thank You!
- Please inspect the product to ensure there was no damage incurred during shipping.
- If there is damage to report, please contact the White Top Adventures Customer Service Department as soon as possible.
- Next, using the "Package Contents" page, check inventory and familiarize yourself with the parts and hardware.
- Gather all tools required for installation.
