PHEANOO P15 Soundbar Quick Start Guide

1. Checking the Components

Ensure all the following components are included:

• Soundbar x1
• Subwoofer x1
• Remote control x1
• HDMI(ARC) cable x1
• Optical cable x1
• 3.5mm to RCA audio cable
• AC power cord
• Mounting template
• Screws bag x1
• User manual x1
• Quick Start Guide x1

Note: Batteries are not included for shipping safety. Two AAA batteries are needed for the remote control.

2. Connecting a TV

Choose one of the following connection options:

Option 1 (Preferred): HDMI ARC

Connect the HDMI cable to your TV's HDMI ARC jack and the soundbar's HDMI ARC jack. This option enables TV remote control for power on/off and volume adjustment.

Note: This connection is only available if your TV has an HDMI port labeled "ARC".

Option 2: OPTICAL

Connect the optical cable to your TV's OPTICAL OUT jack and the soundbar's OPTICAL IN jack. This is used if your TV does not have an ARC-labeled HDMI port.

Option 3: AUX

Connect the 3.5mm to RCA audio cable to your TV's AUDIO OUT jack and the soundbar's AUX IN jack. This is used if your TV has no ARC-labeled HDMI ports.

Note: If you hear audio from the TV's internal speaker, ensure the TV speakers are turned off or set to minimum volume.

Note: Some TV models have an AUDIO IN jack only, which cannot deliver an audio signal to the soundbar.

3. Power Your System

Connect the AC power cord to the soundbar and plug it into a power outlet.

4. Choose Input Mode

Select the appropriate input mode on the soundbar using the remote control (TV ARC, OPT, AUX, BT) to match your TV connection method. The corresponding LED indicator on the soundbar should light up.

Note: The input mode on the soundbar must match the output mode of the connected external device.

5. Change Audio Settings on Your TV

! Very Important!!!

For optimal performance, adjust your TV's audio settings. Below are recommended settings for popular TV brands. Refer to your TV manual if your brand is not listed or for specific instructions.

General TV Settings:

1. Change the TV audio output format to PCM.
2. Enable Consumer Electronics Control (CEC) on your TV.

Note: CEC is only required for HDMI ARC connection. Different brands may use different names for CEC (e.g., Samsung: Anynet+++, Sony: Bravia Sync, LG: SimpLink).

Brand-Specific Settings:

• Samsung TV: Sound > Sound Output > Receiver (HDMI); Sound > Expert Settings > Digital Output Audio Format > PCM; General > External Device Manager > Anynet+ (HDMI-CEC) > ON.
• TCL ROKU TV: Audio > Audio output > Auto; Audio > Digital audio format > Stereo.
• TCL TV (Android): Audio > Advanced Settings > Digital Audio Out > PCM; System > T-Link > ON.
• Sharp TV (Android): Devices Preferences > Sound > Digital Output > PCM; Devices Preferences > Sound > Speakers > External audio system.
• Vizio TV: Audio > TV Speakers > Off; Audio > Digital Audio Out > PCM; System > CEC > Enabled.
• Sony TV: Display & Sounds > Audio Output > Speakers > Audio System; Display & Sounds > Audio Output > Digital Audio Out > PCM; Display & Sounds > Audio Output > Pass Through Mode > OFF; Channels & Inputs > External Inputs > BRAVIA Sync > BRAVIA Sync control > ON.
• LG TV: General-Devices > HDMI Settings > SIMPLINK (HDMI-CEC) > ON; Sound > Advanced Settings > Digital Sound Output > PCM; Sound > Sound Out > Use Wired Speaker > HDMI (ARC) Device.
• Hisense ROKU TV: Audio > TV Speakers > Disabled; Audio > Digital Audio out > Stereo.
• Hisense TV (Android): Sound > Speakers > ARC; Sound > Advanced Settings > Digital Audio Out > PCM.
• Roku TV Stick: Audio > Digital Output Format > Stereo; Audio > Audio Mode > Stereo.
• ONN ROKU TV: Audio > TV Speakers > Disabled; Audio > Digital Audio Format > Stereo.
• Sharp TV: Sound > Advanced audio settings > TV Speaker & ARC > ARC; Sound > Advanced audio settings > Digital Audio Out > PCM.
• Toshiba Fire TV / Amazon Fire TV / Insignia Fire TV: Display & Sounds > Audio Output > TV Speakers > OFF; Display & Sounds > Audio Output > Digital Audio Format > PCM; Display & Sounds > HDMI CEC Device Control > ON.
• Panasonic TV: Display & Sounds > Audio > Surround Sound > PCM; Display & Sounds > HDMI CEC Device Control > ON.
• Fire TV stick: Menu > Audio Settings > Advanced Audio > TV Speakers > OFF; Menu > Audio Settings > Advanced Audio > HDMI > DIGITAL; Menu > Audio Settings > Advanced Audio > Digital Audio Out > PCM.

6. "VOLUME BEEF UP" Function

If the soundbar volume is not loud enough compared to your TV speakers, even at maximum volume, you can enable the "VOLUME BEEF UP" function. This function increases the soundbar's volume level, especially for TVs with lower audio output power.

Note: If your TV's audio output power is already high, enabling this function may cause distortion, crackling, static, noise, or trigger power protection. If this occurs, disable the function.

How to enable the "VOLUME BEEF UP" function:

1. Long press the MUTE button (marked with an 'X' symbol) on the soundbar remote control for 3-5 seconds.
2. The soundbar will enter the enable/disable surface for this function.
3. Press the VOL+ button on the soundbar remote control twice.

How to disable the "VOLUME BEEF UP" function:

1. Long press the MUTE button (marked with an 'X' symbol) on the soundbar remote control for 3-5 seconds.
2. The soundbar will enter the enable/disable surface for this function.
3. Press the VOL- button on the soundbar remote control twice.

7. Control Your Soundbar

7a. Top Panel Controls:

• POWER: Turns the soundbar on or sets it to standby mode.
• MUTE: Temporarily turns off the sound.
• VOL+: Increases volume.
• VOL-: Decreases volume.
• RESET (PLAY/PAUSE): Starts, pauses, or resumes playback in BT Mode. Press and hold for about 2 seconds to reset the volume level and switch to Movie EQ effect.
• BASS+: Increases bass level.
• BASS-: Decreases bass level.
• TV ARC: Sets the input source to HDMI ARC mode.
• BT: Sets the input source to Bluetooth mode.
• AUX: Sets the input source to AUX mode.
• OPT: Sets the input source to Optical mode.
• MUSIC: Selects MUSIC sound effect.
• MOVIE: Selects MOVIE sound effect.
• DIALOGUE: Selects DIALOGUE sound effect.
• INDICATOR: Turns the indicators on the soundbar speaker on/off.

7b. Remote Control:

The remote control allows you to manage power, mute, volume, input sources (TV ARC, BT, AUX, OPT), playback (Play/Pause/Reset), sound effects (MUSIC, MOVIE, DIALOGUE), bass levels (BASS+, BASS-), and indicator lights.

8. Wall Mount Your Soundbar

1. Mark the wall using the provided template.
2. Drill screw holes at the markings.
3. Insert the wall anchors.
4. Insert the screws into the wall anchors.
5. Hang the soundbar on the wall.

9. Firmware Update

PHEANOO occasionally releases firmware updates to improve soundbar performance. You can download and install these updates using a USB drive.

Update Process:

1. Download Firmware: Go to www.pheanoo.com/firmware.html to download the latest firmware version.
2. Prepare USB Drive: Use a USB 2.0 drive with a maximum size of 32GB. Format the USB drive to FAT16 or FAT32. Extract the downloaded firmware file (e.g., "P15 FIRMWARE.zip") and place the "ota.bin" file directly onto the USB drive. Ensure no other files or folders are on the drive. A 2GB flash drive is recommended.
3. Install Firmware: Turn on the soundbar using the remote control. Insert the USB drive into the USB (SERVICE) slot on the back of the soundbar. The indicator light on the soundbar will flash white during installation.
4. Completion: Once the firmware is installed, the light will stop flashing and turn solid red. It is now safe to remove the USB drive.

IMPORTANT:

• Only USB drives with the specified specs (USB 2.0, Max 32GB) will work.
• Do not remove the USB drive or turn off the soundbar during the upgrade process.
• If the soundbar system does not function correctly after the firmware upgrade, contact support@pheanoo.com.

10. Bluetooth Connection (Optional)

1. Press the Bluetooth button on the soundbar or remote until the Bluetooth LED blinks blue.
2. On your device, go to Bluetooth settings and ensure Bluetooth is turned ON.
3. Select "PHEANOO P15" from the list of available devices. The Bluetooth LED will turn solid blue when paired.

11. Troubleshooting

Issue: No sound from SoundBar speakers

• Ensure the soundbar is powered on.
• Verify the HDMI cable is connected to an HDMI ARC or Audio Return Channel port on your TV, not a standard HDMI port.
• If using HDMI ARC, confirm that Consumer Electronics Control (CEC) is enabled in your TV's system menu (refer to your TV's manual for specific naming).
• Select the correct audio input source on the remote control.
• Ensure the TV's audio output format is set to PCM.

Issue: Distorted sound or echo

• If playing audio from the TV through the soundbar, ensure the TV's internal speakers are muted.

Issue: A device cannot connect with the SoundBar via Bluetooth

• Make sure the Bluetooth function is enabled on your device.
• Disconnect the soundbar from any other previously connected Bluetooth devices, then try connecting again.