iScooter W8 User Manual

FCC Compliance and Statements

FCC ID: 2BBGK-W7

This equipment has been tested and found to comply with the limits for Class B digital devices, in alignment with section 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. Users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.

Disposal and Compliance

• Disposal of Electrical and Electronic Equipment: The crossed-out garbage can means that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. If the products contain batteries or rechargeable batteries that are not permanently installed, they must be removed before disposal and disposed of separately as a battery.
• Options for Returning Old Devices (EAR): Owners of old devices can hand them over within the scope of the options for returning or collecting old devices that have been set up and made available by public waste disposal authorities, so that proper disposal of the old devices is ensured.
• Declaration of Conformity: Shenzhen Xincheng Times Technology Co., Ltd, hereby declares that the device complies with the legal regulations of the EU Directives 2014/30/EU and 2011/65/EU (RoHS). For the full text of the EU Declaration of Conformity, visit the link: https://www.iscooterglobal.co.uk/pages/declaration-of-conformity (UK) or https://www.iscooterglobal.de/pages/konformitatserklarung (EU).

Package Contents

The package includes:

• Scooter
• Charger
• Stem Bolt x6 (Including 2 Spare Bolts)
• Hex Wrench

Product Overview

The iScooter W8 features the following components:

1. Bell & Folding Buckle
2. Brake Lever
3. Headlight
4. Folding Latch
5. Turn Signal
6. Kickstand
7. Turn Signal
8. Display
9. Throttle & Turn Signal Switch
10. Charging Port
11. Underbody Light
12. Taillight & Brake Light
13. Disc Brake

Quick Setup

Assembly

1. Raise the stem to the riding position and close the folding latch until you hear a click.
2. Connect the handlebar assembly to the stem, pre-tighten all four bolts, then tighten them with the supplied hex wrench.

Folding

1. Turn the scooter off, open the folding latch, fold down the stem so that the hook on the rear fender catches the folding buckle on the handlebar.

Unfolding

1. Press the folding buckle to release the handlebar from the rear fender and lift the stem to the riding position. Then close the folding latch until you hear a click.

About Charging

• The scooter is fully charged when the charger indicator changes from red to green.
• With charging protection, the scooter will cut off charging automatically after a full charge. It is not recommended to charge it continuously for more than 24 hours.
• Keep the charging port cover closed when not charging.

Display Information

The display shows the following information:

1. Real-Time Speed
2. Speed Unit (km/h or mph)
3. Riding Mode (ECO, D, S)
4. Headlight & Taillight status
5. Cruise Control status
6. Motor Overheating indicator
7. Battery Level indicator
8. App Connected status
9. Error Code

Riding Modes and Speed:

Error Codes

If you encounter any error codes on the display, please contact the iScooter support team. Common error codes include:

• E10: Communication Fault
• E14: Throttle Fault
• E15: Brake Lever Fault
• E16: Motor Hall Sensor Fault
• E50: Over-Voltage

Basic Operations

• Turn On/Off: Press and hold the Power button.
• Lights: Short press the Power button to turn on/off the headlight, taillight, and underbody light.
• Riding Modes: Double-press the Power button to cycle through the four riding modes.
• Speed Unit: Press the Power button three times to switch between km/h and mph.
• Zero Start and Non-zero Start: Press the Power button four times to switch between zero start and non-zero start.
• Cruise Control: Press the Power button five times to enable or disable cruise control (enabled by default).

Notes:

• The scooter will automatically shut down if there is no operation for 10 minutes.
• When cruise control is turned on, maintain a speed for 5 seconds, and the scooter will move forward at this speed without applying the throttle.

Specifications

• Model: W8
• Unfolded Size: 1170 x 430 x 1230 mm (46 x 16.9 x 48.4 in)
• Folded Size: 1170 x 430 x 570 mm (46 x 16.9 x 22.4 in)
• Weight: 21 kg (46.6 lbs)
• Battery Capacity: 10.4 Ah
• Motor Power: 500 W
• Wheel: 9.3 in. Pneumatic Off-Road Tyres
• Range: 35-40 km (21-25 miles)
• Max Load Capacity: 120 kg (264 lbs)
• Recommended Age: 14+
• Operating Temperature: -2 to 35 °C (28.4 - 95°F)
• Charger Input: AC 100~240 V, 50/60 Hz
• Charger Output: 54.6 V, 2 A
• Charging Time: 5-6 h

Range and Load Capacity

• The range is measured under the condition of 100% battery level, a load of 70kg (154lbs), and a speed of 15km/h (9mph). The actual range may differ based on factors like load, humidity, wind speed, and operation habits.
• The scooter is designed to support a maximum load of 120 kg. For the best riding experience, it is recommended to use 70% of the maximum load.