iScooter W8 User Manual

FCC ID: 2BBGK-W7

NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, in alignment with section 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

ISED Statement

English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux RSS exemptés de licence d'Innovation, Sciences et Développement économique Canada.

L'exploitation est soumise aux deux conditions suivantes :

1. Cet appareil ne doit pas provoquer d'interférences.
2. Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil.

l'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies pour un environnement non contrôlé.

The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body.

L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF. Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre corps.

Disposal of Electrical and Electronic Equipment

The crossed-out garbage can means that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. If the products contain batteries or rechargeable batteries that are not permanently installed, they must be removed before disposal and disposed of separately as a battery.

Options for Returning Old Devices (EAR)

Owners of old devices can hand them over within the scope of the options for returning or collecting old devices that have been set up and made available by public waste disposal authorities, so that proper disposal of the old devices is ensured.

Declaration of Conformity

Shenzhen Xincheng Times Technology Co., Ltd, hereby declares that the device complies with the legal regulations of the EU Directives 2014/30/EU and 2011/65/EU (RoHS). For the full text of the EU Declaration of Conformity, visit the link: https://www.iscooterglobal.co.uk/pages/declaration-of-conformity (UK) https://www.iscooterglobal.de/pages/konformitatserklarung (EU)

Package Contents

The package includes:

• Scooter
• Charger
• Stem Bolt x6 (Including 2 Spare Bolts)
• Hex Wrench

Product Overview

The iScooter W8 has the following components:

1. Bell & Folding Buckle
2. Brake Lever
3. Headlight
4. Folding Latch
5. Turn Signal
6. Kickstand
7. Turn Signal
8. Display
9. Throttle & Turn Signal Switch
10. Charging Port
11. Underbody Light
12. Taillight & Brake Light
13. Disc Brake

Quick Setup / Assembly

1. Raise the stem to the riding position and close the folding latch until you hear a click.
2. Connect the handlebar assembly to the stem, pre-tighten all four bolts, then tighten them with the supplied hex wrench.

Folding / Unfolding

Folding

1. Turn the scooter off, open the folding latch.
2. Fold down the stem so that the hook on the rear fender catches the folding buckle on the handlebar.

Unfolding

1. Press the folding buckle to release the handlebar from the rear fender.
2. Lift the stem to the riding position.
3. Close the folding latch until you hear a click.

About Charging

• The scooter is fully charged when the charger indicator changes from red to green.
• With charging protection, the scooter will cut off charging automatically after a full charge. It is not recommended to charge it continuously for more than 24 hours.
• Keep the charging port cover closed when not charging.

Display

The display shows the following information:

1. Real-Time Speed
2. Speed Unit
3. Riding Mode
4. Headlight & Taillight indicator
5. Cruise Control indicator
6. Motor Overheating warning
7. Battery Level indicator
8. App Connected status
9. Error Code

Riding Modes and Speeds:

Error Codes

If you see any error code listed below on the display, please contact the iScooter support team to resolve the issue.

Power Button Functions

• Turn On/Off: Press and hold the Power button to turn the scooter on/off.
• Lights: Short press the Power button to turn on/off the headlight, taillight, and underbody light.
• Riding Modes: Double-press the Power button to cycle through the four riding modes.
• Speed Unit: Press the Power button three times to switch between km/h and mph.
• Zero Start and Non-zero Start: Press the Power button four times to switch between zero start and non-zero start.
• Cruise Control: Press the Power button five times to enable or disable cruise control. (Enabled by default.)

Note:

• The scooter will automatically shut down if there is no operation for 10 minutes.
• When cruise control is turned on, keep a speed for 5 seconds and the scooter will move forward at this speed without applying the throttle.

Specifications

Range Information

• The range is measured under the condition of a 100% battery level, a load of 70kg (154lbs), and a speed of 15km/h (9mph). The range will differ depending on factors like load, humidity, wind speed, and operation habits.
• The scooter's structure is designed to support a maximum 120 kg load. For the best riding experience, 70% of the maximum load is recommended.

Customer Service

Contact iScooter if you experience issues relating to riding, maintenance, safety, or errors/faults with your electric scooter.

• US: www.iscooterglobal.com, support@iscooterglobal.com, +1 888 4968123
• UK: www.iscooterglobal.co.uk, support@iscooterglobal.co.uk, +44 1888 785356
• FR: www.ihoverboard.fr, support@ihoverboard.com, +33 805980335
• DE: www.iscooterglobal.de, support@iscooterglobal.de, +49 800 0003728

Manufacturer Information

MANUFACTURER: Shenzhen Xincheng Times Technology Co., Ltd

Address: 104-105, Block C, Donghai Wang Building, No.369 Bulong Road, Ma'antang Community, Bantian Street, Longgang District, Shenzhen

EU REP: Tiger-Zhou UG (haftungsbeschränkt)

Address: Shukowstr. 6, 04347 Leipzig, Deutschland

Email: Tiger-Zhou@web.de

Tel: +49 1521 6791470

App Installation

Install the "X-Scooter" App to enhance your experience. Download the app by scanning the QR code or searching "X-Scooter" on the App Store (iOS) or Google Play Store (Android).