Mini Bluetooth Barcode Scanner User Guide

Features

• Wired, wireless, and Bluetooth triple-mode switching.
• Large capacity storage, safe and reliable, stores over 50,000 barcodes offline.
• Unique power management system for ultra-long standby time.
• Supports rich symbologies.
• Adopts imported trigger button with long lifespan, ergonomic design.
• Supports Android/iOS devices/Windows.
• Supports HID, SPP, BLE protocols.
• Mini size, fashion design, and portable.
• Ultra low power consumption and standby time setup available.
• Bluetooth transmission distance: 15m (indoor).
• Supports simultaneous data upload and battery charging via USB cable.

Performance Parameters

Working Conditions

Button Description

Scan Button: Used to initiate scanning.

Indicator Light: Shows device status (e.g., charging, successful scan).

Bluetooth Pairing STEPS

Pair with operating systems (Android, iOS, Windows) that have Bluetooth function:

1. Start the scanner and long press for 8 seconds, or scan the Bluetooth pairing setup barcode to enter Bluetooth search mode.
2. Turn on Bluetooth on your device and search for devices named "Barcode Scanner HID". If pairing is successful, you will hear a beep.

Note: If the scanner enters matching state and does not pair successfully within 1 minute, it will emit two long low sounds indicating failure and return to scanning mode. (Alternatively, trigger twice to exit matching mode and revert to scanning state). If you plug in the USB cable, it cannot pair with the dongle.

2.4G Pairing Steps

For PC terminals without Bluetooth, pair with the included Dongle:

1. Scan the Dongle setup barcode.
2. Scan the "Compulsory Pair with Dongle Setup Barcode" to enter pairing state.
3. Plug in the receiver. If pairing is successful, you will hear a beep.

Note: If the scanner enters matching state and does not pair with the dongle successfully within 1 minute, it will emit two long low sounds indicating failure and return to scanning mode. (Alternatively, trigger twice to exit matching mode and revert to scanning state). If you plug in the USB cable, it cannot pair with the dongle.

Operating Mode

Normal Mode: Scans are uploaded directly to the computer via USB cable or the Wi-Fi dongle. A short, low-frequency tone indicates a successful scan. Three short, low-frequency tones indicate failure, and data will be lost. Scan the "Normal Mode" barcode to enable this mode.

Storage Mode: Recommended when the transfer range is exceeded. Scans are stored in internal storage. A short tone indicates a successful scan and storage. If internal storage is full, three low-frequency short tones will sound as an alarm. Scan the "Storage Mode" barcode to enable this mode.

Data Upload: Scan the "Data Upload" barcode to upload stored data. This does not automatically delete barcodes from the scanner. Scan multiple times if needed. Ensure a stable wireless signal or connect via USB cable for optimal upload. Scan the "Clear Data" barcode to erase stored scans; confirm they have been uploaded before clearing.

Configuration Barcodes

Scan the following barcodes to configure the scanner:

End Character Settings

• Add CR [Carriage Return]
• Add LF [Line Feed]
• Add CR+LF [Carriage Return + Line Feed]
• Cancel CR+LF [Cancel Carriage Return + Line Feed]
• Add TAB [Tab Character]

Standby Time Settings

• Standby after 1 min
• Standby after 5 mins
• Standby after 10 mins
• Standby after 30 mins
• Never enters Standby
• Standby fastly

Language Settings

• English
• German
• French
• Spanish
• Italian
• Japanese
• Only for PC American Keyboard output

Capital and Lowcase Switch

• Transfer to Lowcase Set
• Transfer to Capital Set
• Capital and Lowcase Switch

Pull up and Hide IOS Keyboard

• Pull up and Hide IOS Keyboard
• Trigger twice to pull up iOS keyboard
• Trigger twice to disable iOS keyboard

Bluetooth Protocol

• Select the desired communication Bluetooth protocol:
• HID mode
• SPP mode
• BLE mode

[Note: Scan above barcode to enter the Bluetooth searching state]

Sound and Vibration Setting

• Turn Off the Sound
• Turn On the Sound
• Turn Off the Vibration (Option)
• Turn On the Vibration (Option)

LED Indicator

Buzzer

[Note: During normal usage or start-up process, if the buzzer continuously makes five times long sound (low frequency), then automatically powers off. It means the power capacity is too low and needs to be charged before use.]

Reset Configuration to Defaults

If the scanner is not performing normally due to scanning incorrect setup barcodes, scan the initialization setup barcode to revert to default settings.

[Reset Configuration to Defaults barcode]

Version Information

Contains version information for the scanner.

Disclaimer

The company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, floods, etc.) that exceed its ability to act.

The company is not responsible for any product liability associated with or arising from the application or use of any product, circuit, or other application described herein. About the system, equipment, machinery, materials, methods, or processes that may be used in this product, or any combination with this product, the company does not express, imply, estoppel, or permission in any other means in connection with a patent or patent. The company only provides implied licenses for the equipment, circuits, and subsystems included in its products.

The company does not assume any responsibility for losses caused by improper use of communication hardware or software not specified.

The company does not assume any form of guarantee and technical support responsibility for third-party software used.