2.4G Wireless Barcode Scanner User's Guide
Features
- Wired and wireless dual mode freely switching.
- Large capacity storage, safe and reliable.
- Stores barcodes for more than 50,000 items off-line scanning.
- Unique power management system for ultra-long standby time.
- Rich symbologies supported.
- Adopts imported trigger button, offering a long lifespan and comfortable use.
- Ultra-low power consumption and standby time setup available.
- Supports uploading data and charging the battery via USB cable simultaneously.
Performance Parameters
Wireless protocol: 2.4G
Memory: 16Mb
Processor: ARM Cortex 32bits
Supported symbologies: 1D: Codabar, Code 11, Code 93, MSI, Code 128, UCC/EAN-128, Code 39, EAN-8, EAN-13, UPC-A, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix. 2D: QR, DataMatrix, PDF417, Aztec, Hanxin, Micro PDF417 (option).
Indicator: LED, Buzzer, Vibrator (option).
Battery capacity: 1800mA
Charging voltage/current: 5V/1A
Endurance: 1D ≤ 24H, 2D ≤ 16H (based on 5 seconds/scan)
Charge time: < 4 hours
Standby: > 30 days
Working Conditions
Working Temperature: 0°C to 40°C (32°F to 104°F)
Storage Temperature: -40°C to 80°C (-40°F to 140°F)
Humidity: 5% to 95% relative humidity (no condensation).
Ruggedness: Withstands drops from 1.5m onto concrete ground.
Ambient Light Immunity: Operates normally under standard office/factory lighting conditions or direct sunlight.
Electrostatic discharge: Complies with 15KV air discharge and 8KV contact discharge requirements.
2.4G Pairing Steps
- Scan the "Compulsory Pair with Dongle Setup Barcode" to enter pairing state. The blue indicator light will flicker.
- Plug the USB receiver into the PC USB interface.
- If pairing is successful, you will hear a beep, and the blue indicator light will remain constantly on.
Note: If the scanner does not pair successfully with the dongle within 1 minute, it will emit two long low sounds, indicating a failed match, and return to scanning mode. You can also trigger the scanner twice to exit matching mode and revert to scanning state.
Note: Plugging in the USB cable prevents pairing with the dongle.
Operating Modes
Normal Mode
In normal mode, scanned data is uploaded directly to the computer via USB cable or the Wi-Fi dongle. A successful scan is indicated by a low-frequency short tone. If a scan fails, three low-frequency short tones will sound as an alarm, and the data will be lost.
Storage Mode
This mode is recommended for situations where the transfer range exceeds the wireless capability. Scans are stored in the scanner's internal storage. A successful scan in storage mode produces a short tone, and the data is automatically stored. If the internal storage becomes full, the scanner will emit three low-frequency short tones to alert the user.
To check the total amount of stored barcodes, scan the "Total amount of stored barcode" barcode.
Data Upload
Upload stored data by scanning the "Data Upload" barcode. After data upload, the barcodes are not automatically deleted from the scanner. Users can scan the "Data Upload" barcode multiple times to transfer all stored data.
Note: Ensure a stable wireless signal for uploading, or connect the scanner via USB cable for the upload process.
Clear Data
Clear all stored scans by scanning the "Clear Data" barcode. Cleared scans cannot be uploaded. Please confirm that all necessary data has been uploaded before clearing.
End Character Settings
Choose the end character you need to add to scanned data:
- Add CR
- Add LF
- Add CR+LF
- Cancel CR+LF
- Add TAB
Standby Time Settings
Configure the scanner's standby time:
- Standby after 1 min
- Standby after 5 mins
- Standby after 10 mins
- Standby after 30 mins
- Never enters Standby
- Standby fastly
Language Settings
Select the desired language for the scanner's interface or output:
- English
- German
- French
- Spanish
- Italian
- Japanese (Only for PC American Keyboard output)
Capital and Lowcase Switch
Control the case of scanned data:
- Transfer to Lowcase Set
- Transfer to Capital Set
- Turn off Switch
- Capital and Lowcase Switch
Hide Prefix and Suffix
Configure prefix and suffix hiding for scanned data:
A: Scan "Hide Prefix" or "Hide Suffix" setup barcodes.
B: Select the bits to be hidden:
- Hide 1 bit
- Hide 2 bits
- Hide 3 bits
- Hide 4 bits
- Hide 5 bits
- Hide 6 bits
- Hide 7 bits
- Hide 8 bits
Note: To cancel the Prefix or Suffix hide function, scan the corresponding "Hide Prefix" or "Hide Suffix" setup barcode again.
Reset Configuration to Defaults
If the scanner's performance becomes abnormal due to scanning incorrect setup barcodes, you can scan the "Reset Configuration to Defaults" barcode to revert all settings to their original state.
LED Indicator
- Blue light flicker and extinct fastly: Indicates successful barcode reading and makes a short sound.
- Red light (charging lamp): Red light indicates the charging state. The light turns off when the battery is fully charged.
Buzzer
The buzzer provides audible feedback for various operations:
| Sound Type | Description |
|---|---|
| A long sound (First low then high frequency) | Means power on |
| A long sound (First high then low frequency) | Means power off |
| A short sound (low frequency) | Means read barcode |
| A short sound (First low then high frequency) | Means data has been stored |
| A short sound (First high then low frequency) | Means scan the set-up barcode |
| A short sound (low frequency) | Means wireless transmission failed or cache is full |
Low Power Warning: During normal usage or startup, if the buzzer continuously emits five long low-frequency sounds, the scanner will automatically power off. This indicates the battery capacity is too low and requires charging before the next use.
Sound and Vibration Setting
Configure sound and vibration feedback:
- Turn Off the Sound
- Turn On the Sound
- Turn Off the Vibration (Option)
- Turn On the Vibration (Option)
Disclaimer
The company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, floods, etc.) that exceed its ability to act.
The company is not responsible for any product liability associated with or arising from the application or use of any product, circuit, or other application described herein. The company does not express, imply, or estoppel permission in any other means regarding systems, equipment, machinery, materials, methods, or processes that may be used in this product, or any combination with this product, concerning patents. The company only provides implied licenses for the equipment, circuits, and subsystems included in its products.
The company does not assume any responsibility for losses caused by improper use of communication hardware or software not specified.
The company does not assume any form of guarantee and technical support responsibility for third-party software used.
