QDD-ZR-400G TEST REPORT (Cisco)
1. Test Purpose
The test object is the QDD-ZR-400G Transceiver. Testing the module provides a foundation for subsequent cooperation with customers.
2. Test Results Summary
| 1st Items | Test Data | Remarks |
|---|---|---|
| Product Software Performance Testing | Pass | |
| Product Compatibility Testing | Pass |
3. Test Environment
3.1 Test Equipment Used
| Vendor | Device | Soft Version | Hardware Version |
|---|---|---|---|
| FS | Coding Board | ||
| Cisco | Nexus9000 C9332D-GX2B | 10.4(2) |
3.2 Test Sample
| Product ID | P/N | Serial Number |
|---|---|---|
| #193134 | QDD-ZR-400G | A2310220131 |
4. Test Data
4.1 Product Software Performance Testing
Test Topology: A PC is connected to an FS Coding board, which is then connected to the QDD-400G ZR transceiver.
Test Scenario: The test setup involves a rack of networking equipment, including the FS Coding board and the transceiver, for performance evaluation.
Test Premise
1. The equipment can be powered up and run normally.
2. A test environment is built according to the networking described.
Test Equipment
Device: QDD-ZR-400G
Model No.: A2310220131
Test Method
1. The FS Coding board can read the P/N, serial number, optic type, and vendor name of the transceiver.
2. The transceiver is successfully coded by the FS Coding board.
3. With the FS Coding board and PC powered on, the optics are plugged and unplugged at least five times, and the read information is checked for consistency.
| Items | Test Method | Content | The Results |
|---|---|---|---|
| Function | Accessible Page | Pass | |
| Coding | Pass | ||
| Upgrade | Firmware Online Upgrade | Pass | |
| Stability | Hot Swap | Pass |
Test Conclusion
After testing, the results of all tested items meet the requirements of the inspection basis.
Remarks
4.2 Product Compatibility Testing
Test Topology: A Switch is connected via a QSFP-DD-400G transceiver to a DWDM MUX DEMUX. A loopback connection is also present.
Test Equipment
Device: Cisco Nexus9000 C9332D-GX2B
Model No.: Nexus9000 C9332D-GX2B
Test Method
1. Check if the optics DDM threshold is accurate.
2. Check if DDM parameters, basic optics information, device port information, and device log information are normal.
Test Information
Software
Operating System: Cisco Nexus Operating System (NX-OS) Software
TAC Support: http://www.cisco.com/tac
Copyright: © 2002-2023, Cisco and/or its affiliates.
Software Licenses: Mentions GNU General Public License (GPL) versions 2.0/3.0 and GNU Lesser General Public License (LGPL) versions 2.1/2.0. Links provided for license details: gpl-2.0.php, gpl-3.0.html, lgpl-2.1.php, library.txt.
BIOS Version: 01.11
NXOS Version: 10.4(2) [Feature Release]
Host NXOS Version: 10.4(2)
BIOS Compile Time: 06/30/2023
NXOS Image File: bootflash:///nxos64-cs.10.4.2.F.bin
NXOS Compile Time: 11/30/2023 12:00:00 [12/14/2023 05:25:50]
NXOS Boot Mode: LXC
Hardware
Chassis: Cisco Nexus 9000 C9332D-GX2B Chassis
CPU: Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32801496 kB of memory.
Processor Board ID: FDO26450X3Y
Device Name: n
Kernel Uptime: 0 days, 0 hours, 43 minutes, 48 seconds
Last Reset Reason: Reset due to upgrade
System Version: 10.4(3)
Service: Core Plugin, Ethernet Plugin
Inventory
Chassis: NAME: "Chassis", DESCR: "Nexus9000 C9332D-GX2B Chassis", PID: N9K-C9332D-GX2B, VID: V01, SN: FDO26450X3Y
Slot 1: NAME: "Slot 1", DESCR: "32x400G QSFP-DD + 2x10G SFP+ Ethernet Module", PID: N9K-C9332D-GX2B, VID: V01, SN: FDO26450X3Y
Slot 27: NAME: "Slot 27", DESCR: "32x400G QSFP-DD + 2x10G SFP+ Ethernet Module", PID: N9K-C9332D-GX2B, VID: V01, SN: FDO26450X3Y
Power Supply 1: NAME: "Power Supply 1", DESCR: "Nexus9000 C9332D-GX2B Chassis Power Supply", PID: NXA-PAC-1500W-PI, VID: V01, SN: POG2646FTDA
Power Supply 2: NAME: "Power Supply 2", DESCR: "Nexus9000 C9332D-GX2B Chassis Power Supply", PID: NXA-PAC-1500W-PI, VID: V01, SN: POG2646FT6T
Fan 1: NAME: "Fan 1", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Fan 2: NAME: "Fan 2", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Fan 3: NAME: "Fan 3", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Fan 4: NAME: "Fan 4", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Fan 5: NAME: "Fan 5", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Fan 6: NAME: "Fan 6", DESCR: "Nexus9000 C9332D-GX2B Chassis Fan Module", PID: NXA-SFAN-35CFM-PI, VID: V01, SN: N/A
Interface Configuration (Ethernet 1/1)
zr-optics fec cFEC muxponder 1x400 modulation 16QAM dac-rate 1x1
zr-optics cd-min -2300 cd-max 2300
zr-optics transmit-power-70
zr-optics dwdm-carrier 100MHz-grid frequency 1921000
no shutdown
Interface Status
| Port | Name | Status | Vlan | Duplex | Speed | Type |
|---|---|---|---|---|---|---|
| mgmt0 | notconnec | routed | auto | auto | ||
| Eth1/1 | connected | 1 | full | 400G | QSFP-DD-400G-ZR-S |
Interface Transceiver Details (Ethernet 1/1)
Transceiver is present.
Type: QSFP-DD-400G-ZR-S
Name: FS
Part Number: QDD-ZR-400G
Revision: A
Serial Number: A2310220126
Nominal Bitrate: 425000 MBit/sec per channel
Cisco ID: 24
Cisco Extended ID Number: 21
Firmware Version: 2.11
Link Length SMF: 8 km
Nominal Transmitter Wavelength: 1547.70 nm
Wavelength Tolerance: 0.015 nm
Host Lane Count: 8
Module Parameters
Media Lane Count: 1
Max Module Temperature: 70 deg C
Min Module Temperature: 0 deg C
Min Operational Voltage: 3.14 V
Vendor OUI: 0x7cb25c
Date Code: 240507
CLEI Code: INUIANYEAA
Power Class: 8 (>14 W maximum)
Max Power: 23.75 W
Near-end Lanes Used: none
Far-end Lane Code for 8 lanes: Undefined
Media Interface: unknown value 0x10
Advertising Code: Optical Interfaces: SMF
Host Electrical Interface Code: 400GAUI-8 C2M (Annex 120E)
FEC State
FEC State: FEC CFEC
Optics Status
Optics Type: QSFP-DD-400G-ZR-S
DWDM Carrier Info: Frequency: 192.10 THz
Alarm Status
DAC Rate: 1x1
Threshold Values
Configured Tx Power: 0 dBm
Modulation Type: 16QAM
Muxponder Type: 1x400
Configured CD-MIN: -1430864206 ps/nm
Configured CD-MAX: 530644985 ps/nm
Lane Data (Lane Number: 1 Network Lane)
| Measurement | High | Low | High | Low |
|---|---|---|---|---|
| Alarm | Alarm | Warning | Warning | |
| Temperature | 75.00 C | 0.00 C | 70.00 C | 0.00 C |
| Voltage | 3.60 V | 3.00 V | 3.46 V | 3.13 V |
| Current | N/A | N/A | N/A | N/A |
| Tx Power | 2.99 dBm | -8.01 dBm | 1.99 dBm | -7.01 dBm |
| Rx Power | 7.99 dBm | -23.01 dBm | 7.99 dBm | -22.21 dBm |
| Transmit Fault Count | 0 |
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
*** This QSFP support partial diagnostic data! ***
Test Conclusion
The QDD-ZR-400G module was used in the test. After testing, the test results of the tested items (product software performance) meet the requirements of the test basis.
Remarks
5. Appendix
5.1 Product Software Performance Standards
| Test Items | Content | Standards |
|---|---|---|
| Function | Accessible Page | The model No., serial number, optics type, vendor name and other information of optics can be read. |
| Upgrade | Firmware Online Upgrade | Optics can be coded through BOX successfully |
| Reliability | Hot Swap | When FS BOX and PC are powered on, plug and unplug the optics for at least five times, then check whether the read information are consistent. |
5.2 Product Software Performance Standards
On the basis of threshold value range, the allowable deviation value should be within the standard range that is specified by FS.
| Content | Details | Standards |
|---|---|---|
| Basic Information | Model name | The read model No. is consistent with the model of optics. (If there are special requirements, the actual information shall prevail) |
| SN Number | The read serial number is consistent with the serial number on label of optics. (If there are special requirements, the actual information shall prevail) | |
| Vendor Name | The vendor name information read is FS/OEM. (If there are special requirements, the actual information shall prevail) | |
| Type | The optics type information read by the switch is consistent with the actual optics model. (If there are special requirements, the actual information shall prevail) | |
| DDM Information | Temperature | 1. The actual DDM information is within the DDM threshold and there is no alarm; 2. The DDM threshold range meets the product specification requirements. |
| Voltage | ||
| Bias current | ||
| Tx Power | ||
| Rx Power | ||
| Port Information | Port Rate | The data rate information read on switch port is consistent with the actual rate of the optics |
| Port Status | After the product is connected, the port status information is UP | |
| Switch Indicator Status | After the product is connected, the port indicators at both ends of the product will be green/orange | |
| Switch Log | Except for the official certification warning information, no other warning information |
Related Documents
 |
FS SFP-10G-T-30 Transceiver Test Report for Cisco Compatibility This document presents the comprehensive test results for the FS SFP-10G-T-30 transceiver, verifying its performance and compatibility with Cisco networking environments. It covers test purpose, equipment used, test scenarios, and detailed results. |
 |
FS SFP-10G-T-100 Transceiver Test Report for Cisco Compatibility Comprehensive test report for the FS SFP-10G-T-100 transceiver, detailing its performance and compatibility with Cisco networking equipment, including test scenarios, equipment, and results. |
 |
FS 40GBASE-SR4 QSFP+ 850nm 150m MTP/MPO Transceiver Datasheet Datasheet for the FS 40GBASE-SR4 QSFP+ transceiver module, detailing its specifications, features, electrical and optical characteristics, pin descriptions, mechanical dimensions, and testing procedures for high-speed networking applications. |
 |
FS QSFP-SR4-40G Transceiver Test Report: Cisco Compatibility and Performance A comprehensive test report by FS detailing the performance, compatibility, and Digital Diagnostic Monitoring (DDM) of the QSFP-SR4-40G optical transceiver module with Cisco networking equipment, including test setup, results, and equipment specifications. Features ISO, REACH, CE, FCC, US, CB certifications. |
 |
FS QSFP-LR4-40G Transceiver Test Report for Juniper Compatibility This report details the comprehensive testing and validation of the FS QSFP-LR4-40G transceiver module, confirming its performance and interoperability with Juniper network devices. It covers test purpose, methodology, equipment, and detailed results including DDM information. |
 |
SFP-10G-PCxxx Transceiver Test Report for Cisco Compatibility This report details the test results for the FS SFP-10G-PCxxx transceiver, verifying its performance and compatibility with Cisco equipment, including detailed test scenarios, equipment used, and specific port status. |
 |
FS SFP1G-ELX-31 Transceiver Test Report for Cisco Compatibility This test report details the performance and compatibility testing of the FS SFP1G-ELX-31 SFP transceiver module with Cisco networking equipment, covering test purpose, methodology, and results. |
 |
SFP-10GSR-85 Transceiver Test Report (Cisco Compatible) Detailed test report for the FS SFP-10GSR-85 10GBASE-SR transceiver module, including test purpose, equipment used, test scenarios, results, and Digital Diagnostic Monitoring (DDM) data. Verified for compatibility with Cisco equipment. |