Sanuvair® S1000 CRO Air Purification Unit with Filters

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.

Read and follow all instructions contained in the manual before using the product. Read the maintenance instructions before opening the UV unit or system. Failure to comply with these instructions may result in injuries or damage to the UV unit or system.

NEVER EXPOSE EYES OR SKIN TO AN OPERATING UV LAMP.

• Installation and servicing of UV units or systems can be hazardous. Only trained and qualified service personnel should install, repair or service equipment.
• Untrained personnel can perform basic maintenance functions such as replacing lamp(s) and/or filter(s). All other operations should be performed by trained service personnel.
• The unit is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
• CAUTION: Unit is not a toy. Keep away from unsupervised children. Do not leave children unattended with the unit.
• DO NOT hang onto the UV unit or system.
• Some UV units or systems could be heavy: Make sure you have a minimum of 2 people to safely move or install these UV units or systems. Adopt the most ergonomic position possible (use UV unit or system handles, if applicable).
• CAUTION: Installing or maintaining heavy equipment, especially overhead, can cause back pain or other injuries.
• When installing or servicing an overhead UV unit or system, be careful not to fall off the stepladder. Make sure the UV unit or system latches are always in place to prevent falling parts.
• CAUTION: Some parts of some UV units and systems may open suddenly if the UV unit or system is installed high up without its locks.
• Units that are obviously damaged must not be operated.
• CAUTION: When working on the UV unit or system, observe precautions on the literature, tags and labels attached to the UV unit or system, and all other safety precautions considered as best practices in the HVAC industry, if applicable.
• When applicable, local regulation may comprise more restrictive installation and/or certification requirements. The installer agrees to conform to these at his own expense.
• Follow all the safety instructions outlined in this document and respect all local and national codes applicable.
• All UV units or systems contain a UV-C source. Damage to the housing or unintended use may result in harmful UV-C leaks. UV-C may cause harm to the eyes and skin.
• Never expose eyes or skin to an operating UV lamp. Therefore, before installing or performing maintenance, TURN OFF AND DISCONNECT the UV unit or system from all power sources and disconnect the HVAC system, if applicable.
• CAUTION: Electrical shock may cause injuries or possibly death. FIRST AID INSTRUCTIONS: If injured, consult a doctor.
• UV rays may damage certain types of filters (polymer or plastic); please keep the UV unit or system light away from shining directly on plastic.
• When installing or performing maintenance, it is recommended to wear safety gloves. To avoid reduced performance of lamp(s), do not touch lamp glass without gloves.
• Just like conventional fluorescent lamps, UV lamps contain a small quantity of mercury: if a lamp breaks, clean and dispose of with care. UV lamps can be disposed/recycled after use in the same way as any other fluorescent lamps. Contact and follow the specific instructions of your local and national authorities.
• Dispose of unit or system according to the specific instructions and standards of your local and national authorities.
• WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer.
• Use only specified SANUVOX branded replacement UV lamps for your UV unit or system. Use of any other lamps will void your warranty and can result in damage to the UV unit or system.
• Sanuvox UV units or systems are not waterproof. DO NOT INSTALL OUTDOORS OR IN WET LOCATION unless specified otherwise.
• Use of this unit or system supplements, but does not replace, infection control best practices. Users must follow all these practices, particularly with regard to cleaning and disinfecting surfaces.

SAVE THESE INSTRUCTIONS

For any inquiries on a UV unit or system, contact:

Robert Smith
146 Barr St, Saint-Laurent
Quebec, CA, H4T 1Y4
1-888-726-8869
techsupport@sanuvox.com

Installation Date:
Installer Contact Info.:

Installed by:

ABOUT THE PRODUCT

The Sanuvair® S1000 CRO is designed for air purification of large rooms where HVAC systems are not available or accessible. This stand-alone unit helps reduce microorganisms from the air in a room up to 10,000 cubic feet.

For information or recommendations on how to size your specific application, please call SANUVOX at 1-888-726-8869.

COMPONENTS

How it Works

This unit is constructed of a lightweight aluminum case and has a three-stage purification process:

1. Air is pulled into two return ports through an aluminum reflection chamber that houses 2 high intensity UV lamps.
2. A 2" MERV 8 prefilter captures the large particles.
3. A 4" HEPA filter captures up to 99.97% particles of 0.3 microns in size.

The Sanuvair® S1000 CRO has versatile mounting options.

Diagram Description: The diagram shows the internal components of the Sanuvair S1000 CRO. Labeled parts include:

• A: Holes for 1 x pair of 8" inlet collars
• B: Holes for 1 x pair of 8" outlet collars
• C: 2 x 16" UV 'J' lamps
• D: Aluminum reflecting chamber
• E: 2 ballasts
• F: Door
• G: 1 x 2" MERV 8 prefilter
• H: 1 x 4" HEPA filter
• I: Safety cut-off switch
• J: Power 120 Volt or 230 Volt

SETUP & INSTALLATION

What you will need

Utility knife, scissors, suitable wall plugs and screws (as needed), screwdriver and pliers.

CAUTION: Handle your product with care to avoid breaking parts. Make sure you have a free and safe space to unpack, install and setup your product. Confirm you have access to the necessary power source for the product requirements (see unit or system label). If you have any questions regarding the installation instructions, call SANUVOX at 1-888-726-8869.

What's included

The Sanuvair® S1000 CRO, a 2" MERV 8 prefilter, a 4" HEPA filter, UV lamps (2), 6' of power cord and a basic installation kit.

The installation kit includes: a pair of cotton gloves, standard HVAC 8" collars (4), and large screws for installation (4).

Step by Step Installation | UV Lamp(s) & Filters

1. Open the unit access door of your S1000 unit.
2. The UV lamp(s) will be installed in the Aluminum Reflecting Chamber. To slide out the Aluminum Chamber, remove the two butterfly bolts and screws which secure it in place.
3. Adhere the included foam gasket (included in the Lamp box) to the porcelain end-cap with the 4 pins.
4. Insert the end-cap with foam gasket into the clamp assembly and tighten. Be careful not to over tighten as it may result in end-cap breaking.
5. NOTE: A clamp (or up to four, if you ordered additional lamps) is there to hold the lamp(s).
6. Insert the white-plug into the UV Lamp's 4 pins. The plug will only fit in two of four ways. Either way is fine. The exposed wire-set is Teflon coated and is resistant to UV exposure.
7. UV Lamps and Ballast Position: The lamps should be positioned towards a central point in the middle of the unit's aluminum reflection chamber.
8. Insert Filters: Insert the MERV 8 prefilter and the HEPA filter. Follow the arrow for airflow for proper filter direction.
9. After the main filter is installed, close the latch to secure the filter in place. Close the door of the blower compartment.

You are now ready to install your S1000 unit.

Step by Step Installation | Added Ducts

1. Open the Aluminum Reflecting Chamber access hatch to retrieve the 4 provided 8" fish-lock duct collars. Remove the protective cardboard sheet below the chamber.
2. From the outside, fit the collars over the inlet and outlet holes and fix them in place by prying open their retaining tabs.
3. Secure the unit to the wall OR ceiling, using suitable supports, wall plugs and screws (not included). Make sure you have a power outlet nearby to plug the unit into.
4. CAUTION: Your S1000 unit is bulky. Make sure that there are always two people to lift and handle it to avoid any injuries.
5. Install your 8" pipes (rigid in aluminum or galvanized or aluminized flexible).
6. NOTE: When ducting-in the unit, avoid 90 degree elbows when possible.

Your new Sanuvair® S1000 CRO is now ready to operate!

OPERATION

How to Operate your Product

The Sanuvair® S1000 CRO is an automatic unit: once it's installed and plugged in, simply press the power switch to turn it ON.

How to Select Speed

The Sanuvair® S1000 CRO features a variable speed control, located on the front of the unit.

It is recommended that the unit be operated at its highest speed at all time to maximize the benefits of the air purifier.

MAINTENANCE

How to Replace Lamp

Replace UV lamps every 2 years. Replacing lamps on the Sanuvair® S1000 CRO is quick and easy. Simply turn off the power source, unlatch and open the access door, unscrew the metal access plate to the reflection chamber, remove and dispose of old lamps, replace with new Sanuvox branded UV lamps, screw back the metal plate, close the access door and turn power source back on. See below for detailed step by step instructions.

CAUTION: In order to avoid reduced performance of lamps, do not touch lamp glass without gloves.

Step by Step Lamp Replacement

1. Unlatch and open the access door and unscrew the metal access plate to the reflection chamber.
2. CAUTION: Before installing or performing maintenance on the unit or system, TURN OFF AND DISCONNECT the unit or system from all power sources.
3. Prepare the new lamp. Remove the contents from packaging. Only after you have visually inspected the UV lamp should you break the security seal on the underside of the cardboard sleeve. Be sure to wear the cotton gloves (included) guaranteeing a clean lamp free from fingerprints.
4. NOTE: Fingerprints on the lamp might negatively impact the UV output of the lamp.
5. While holding the new UV lamp by its porcelain end-cap, slide it into the metallic reflection chamber.
6. Slide the porcelain tip through the retention clamp.
7. NOTE: Make sure the lamp is horizontal in this section and not touching the metal walls.
8. Carefully push the white connector onto the four pins. The plug is designed so it can only be installed one way. You may have to rotate the socket 90° to line up the pins with the holes. The connector will fit into position.
9. NOTE: Too much force applied from the opposite end-cap may break the lamp.
10. Repeat steps 2 through 5 for the second lamp.
11. Screw back in place the metal plate and close the access door.

How to Replace Filters

Replace prefilter every 3 to 6 months or as needed.

Replace MERV 15 filter every 1 to 3 years or as needed. Check regularly to maintain maximum performance of your unit.

Step by Step Filter Replacement

1. Open the filters and motor access door at the front of the unit. Start by unlocking the access door latches.
2. After opening the unit's access door, grasp both edges of the HEPA filter and pull with equal force to slide it out.
3. Unpack the new HEPA filter and place it in the unit, then close the access door. Repeat step 2 and 3 for the pre-filter, as needed.
4. NOTE: Make sure to install filters according to air flow direction for maximum performance.

How to Clean your Product

Maintenance of the unit should be performed at regular intervals to keep the benefits of the UV air purifier. For optimal performance, the lamp should be kept free of dust and residue deposit. Clean when necessary with mild soap or alcohol. Always spot test the cleaner to make sure it does not damage the surface.

Once a year or as needed, clean the interior of the unit (wall and motor plate), with mild non-abrasive soap. It is recommended to use products that are environmentally friendly.

CAUTION: Under no circumstance should water be sprayed or splashed onto the product.

STORAGE

The Sanuvair® S1000 CRO unit is fixed installation and therefore, requires no specific storage.

ULTRAVIOLETS

Ultraviolet wavelengths (UV) emitted by Sanuvox units and systems are identical to ultraviolets produced by the sun. UVC damage nucleic acids (DNA/RNA) of microorganisms, which inactivates them. Unlike conventional UV lamps on the market, Sanuvox units and systems use a patented process that delivers a maximum dose of UV to the moving air stream or surfaces.

CAUTION: Never expose eyes or skin to an operating UV lamp.

ELECTRICAL RATINGS, POWER CONSUMPTION & AVAILABLE VOLTAGE

The Sanuvair® S1000 CRO has a power consumption of up to 750W.

The product is rated at 120/240 VAC, 50/60 Hz.

See product label to confirm power consumption of your specific unit or system.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CUSTOMER SERVICE FIRST OR SEE YOUR WARRANTY. DO NOT RETURN THE PRODUCT TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE PRODUCT OR TAMPER WITH ITS COMPONENTS WITHOUT CONTACTING CUSTOMER SERVICE FIRST. DOING SO MAY VOID YOUR WARRANTY AND CAUSE PERSONAL INJURY OR DAMAGE TO THE PRODUCT.

TROUBLESHOOTING

If your product is not working properly, refer to the following.

What you will need

A Phillips No. 2 screwdriver, a non-magnetic 5/16" nutdriver and spare parts.

Contact your contractor for all your needs in terms of replacement parts: power cord, control panel display, UV lamp, ballast, filter, grill, fan motor, stand, handle, etc.

WARRANTY

You should first read all instructions before attempting to use this product.

For this warranty to be valid, keep a copy of the proof of purchase.

UV lamp: 2 years

Ballast: 3 years

Fan Motor: 1 year

Electronics and other parts: 1 year

A. This limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

B. SANUVOX IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

C. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

D. At its option, SANUVOX will repair or replace this product if it is found to be defective in material or workmanship.

E. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

F. This warranty does not cover the filters, prefilters or other accessories (if included), except for material or workmanship defects.

Call us toll-free at 1-888-726-8869 or email: info@sanuvox.com

Please be sure to specify product name.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CUSTOMER SERVICE FIRST OR SEE YOUR WARRANTY. DO NOT RETURN THE PRODUCT TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE PRODUCT OR TAMPER WITH ITS COMPONENTS WITHOUT CONTACTING CUSTOMER SERVICE FIRST. DOING SO MAY VOID YOUR WARRANTY AND CAUSE PERSONAL INJURY OR DAMAGE TO THE PRODUCT.

CUSTOMER SERVICE

TO ORDER REPLACEMENT PARTS

PLEASE CONTACT YOUR CONTRACTOR OR SANUVOX CUSTOMER SERVICE

Toll-Free Phone #: 1-888-726-8869

Email: info@sanuvox.com

Website: www.sanuvox.com

Please be sure to specify product name.

Replacement parts for this product

• BST120/277SHS: Ballast with multi-voltage input of 120-277 VAC, 50/60 Hz
• LMPHGJ160: T6 High Intensity 16" 'J' shaped UV lamp
• FTR-17: MERV 8 Prefilter
• FTR-1: MERV 8 carbon prefilter #FTR-2A
• FTR-12: MERV 15 Filter
• FLEX0825: HEPA Filter
• FLEX0825: 8" diameter flexible tubing, 25' long

WARNING: Use only specified SANUVOX branded replacement UV lamps with your unit or system. Use of any other lamps will void your warranty and can result in damage to the unit, system and/or lamp(s).