Outsunny Garden Swing Assembly & Instruction Manual

Important Notes

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

Only for domestic use.

Use Tips

• Put the swing stably on a flat floor.
• Mount the swing arm in the shelter of the weather.
• Stay away from open flames.
• Don't hang anything in the structure.
• Avoid the overload at the anchors.
• It is advised that don't stay on the swing when there is a storm.
• It is recommended to protect in case of strong wind or rain and in your absence.

Precautions Before Assembly

• Prepare a clean and dry mounting area.
• Verify that the product is not damaged.
• Check that none of the pieces are missing.

Maintenance

• Clean with a soft fabric.
• Regularly remove leaves and/or water collected on the canvas.
• Check the anchors regularly.

Storage Conditions

The fabric should be stored completely dry, in a clean and dry place to avoid the risks of mold.

Caution

Caution with the risks of pinching or cuts during assembly.

The manufacturer declines all responsibility in case of damages due to a bad installation or due to weather.

Packing Details & Parts List

Box 1-2

• A: Curved frame tube (2 pcs)
• B: Curved frame tube (2 pcs)
• C: Top crossbar (1 pc)
• D: Seat back frame (1 pc)
• D1: Seat front frame (1 pc)
• F: Bottom crossbar (1 pc)
• J: Canopy support rod (2 pcs)
• K: Seat support bar (1 pc)
• CC: Fabric piece (2 pcs)

Box 2-2

• E: Seat base (1 pc)
• G: Canopy frame tube (4 pcs)
• H: Canopy frame tube (2 pcs)
• I: Canopy support bar (2 pcs)
• M: Canopy fabric (1 pc)
• N: Seat cushion (1 pc)
• L: Spring (2 pcs)
• Y: Bolt with large washer (2 pcs)
• Z1: Bracket (2 pcs)
• O: Chain (2 pcs)

Hardware Kit

• P: M6*15 Bolt (2 pcs)
• Q: M6*65 Bolt (2 pcs)
• R: M8*60 Bolt (4 pcs)
• S: M6*60 Bolt (4 pcs)
• T: M8*40 Bolt (6 pcs + 1 spare)
• U: M8*75 Bolt (2 pcs)
• V: M6 Washer (6 pcs + 1 spare)
• W: M8 Washer (10 pcs + 1 spare)
• X: Spacer (2 pcs)
• Z: M8 Bolt (2 pcs)
• Z1: Bracket (2 pcs)
• Z2: Hex Key (2 pcs)
• Z3: Wrench (2 pcs)

Assembly Instructions

1. Step 1: Assemble the Main Frame

   Connect two curved frame tubes (A) to the top crossbar (C) and two other curved frame tubes (B). Ensure the holes align for subsequent steps. This forms the upper part of the swing frame.

2. Step 2: Secure the Main Frame

   Attach the assembled frame from Step 1 to the lower frame sections. Use four M8*60 bolts (R) and four M8 washers (W) to secure the connections.

3. Step 3: Attach Seat Support and Lower Crossbar

   Connect the seat support bars (F) and lower crossbar (H) to the main frame. Use four M6*60 bolts (S), two M6*65 bolts (Q), and six M6 washers (V) to secure these connections.

4. Step 4: Assemble the Seat Base

   Attach the seat base (E) to the seat front frame (D1) and seat back frame (D). Use two M6*15 bolts (P), two M8 bolts (Z), and two brackets (Z1) to secure the seat base to the frames.

5. Step 5: Attach Seat to Frame

   Connect the assembled seat (from Step 4) to the main swing frame. Use two M8*40 bolts (T), two M8*75 bolts (U), two spacers (X), and two M8 washers (W). The bolts pass through the frame and the seat's pivot points.

6. Step 6: Attach Canopy Frame

   Attach the canopy frame tubes (G) to the top of the main swing frame. Use four M8*40 bolts (T) and four M8 washers (W) to secure these connections.

7. Step 7: Install Springs

   Attach the two springs (L) to the top crossbar of the main frame.

8. Step 8: Install Canopy Support Bars

   Insert the canopy support bars (I) into the designated slots on the top frame. Secure them using the bolts with large washers (Y).

9. Step 9: Attach Canopy Fabric

   Slide the canopy fabric (M) onto the canopy support rods (J).

10. Step 10: Mount Canopy

    Attach the assembled canopy (from Step 9) to the main swing frame by sliding the canopy support rods (J) into the canopy frame tubes (G).

11. Step 11: Place Seat Cushion

    Place the seat cushion (N) onto the swing seat. The swing is now assembled. Ensure all connections are secure and stable.