COOSPO BC107 USER MANUAL

Button Function

Left Button: Short Press: Mark a new lap. Hold for 2 seconds: Power off. (When powering on: short press the button). (In setting mode: exit / return and save the setting).

Mid Button: Short Press: Pause / Continue (Short press to start recording after power on). Hold for 2 seconds: Save the exercise record and exit the exercise. (In setting mode: enter the current setting / switch the number of digits).

Right Button: Short Press: Page turning. Hold for 2 seconds: Setting mode. (In setting mode: switch setting options / switch the numerical).

Status Icons

• No satellite signal ?️
• Satellite signal level ?
• Accessory connecting status ?
• Under exercising ▶️
• Manual pause ⏸️
• Connected with App by BLE ?
• Temperature ?️
• Battery level ?
• AVG Average
• MAX Maximum
• MPH Miles per hour
• KMH Kilometers per hour
• Increased & Decreased ? / ?
• HRM Heart Rate ❤️
• CAD Cadence ?
• GRA Gradient ⛰️
• TIME Sport time ⏱️
• ALT Altitude ⛰️
• ODO Odometer (Total distance) ?️
• DST Distance ?
• AST Ascend Distance ⬆️
• CAL Calories ?
• LAP Lap ?
• PWR Power ⚡
• UTC Time zone ?

Standard Accessories

• Main Device x 1 ?
• Charging Cable x 1 ?
• User Manual x 1 ?
• Standard bike mount x 1 ?
• Rubber pad for standard bike mount x 1 ⚙️
• Big size rubber ring x 2 ⭕
• Small size rubber ring x 2 ⚪

How to Install (Standard Mount Installation)

1. Install the rubber pad onto the mount.
2. Tie the mount onto the bar with the rubber rings.
3. Tie up the mount.
4. Install the main device onto the mount.
5. Rotate the main device for 90 degrees.
6. Installation completed.

Charging

1. Please charge the device before first-time use.
2. Please use a DC 5V power adapter for charging.
3. During charging, the battery icon will flash until fully charged.

Open the rubber cover, connect the device with USB cable to charge.

Use USB DC 5V power adapter / Computer.

Acquiring Satellite Signals, Time Setting and Auto Backlight

Auto Backlight

This device automatically calculates sunrise and sunset times. The backlight will lighten up from half an hour before sunset to half an hour after sunrise. During the rest of the time, the backlight will turn off if no operation is detected for 15 seconds.

Acquiring Satellite Signals

Ensure the device is outdoors with a clear view of the sky. It usually takes 15-90 seconds to locate satellite signals. Remain stationary while acquiring satellite signals. This device can use a speed sensor or GPS for speed tracking. If the speed sensor is not connected, it uses GPS. If the sensor is connected, it uses the speed sensor.

Time Setting

The time and date will be calibrated automatically after locating satellite signals when the device is powered on. You can also set the time zone correctly (refer to the time zone setting chapter) or connect the device to the App (CoospoRide) to sync the time.

Connecting with ANT+ Sensors

1. Ensure sensors are in wake-up mode (e.g., heart rate monitor worn properly, speed/cadence/power meter awakened by turning pedals or wheels).

Wear it correctly, wake up the heart rate belt.

The speed, cadence, and power meter are awakened by turning the pedals or wheels.

Connecting to ANT+ Peripherals

1. Hold the > button to enter setting mode.
2. There are 5 settings pages available (P1-P5). Press > to switch to P1.
3. Press ►II to select to enter.
4. The computer automatically searches for ANT+ peripherals and connects after searching.
5. Press ⚙️ to save found accessories and return. If no ANT+ accessory is found, the device returns to the last pages automatically. (If a power device is connected during riding, power data is displayed first; if no power device, GRA slope data is displayed).

Save and get back to the last pages (if no device found in 20 seconds, the device will get back to the last pages automatically).

Setting the Wheel Size

1. Hold the > button to enter setting mode.
2. There are 5 settings pages available (P1-P5). Press > to switch to P2.
3. Press ►II to select to enter.
4. Press ►II to select the digit, press > to set the numbers.
5. Press ⚙️ to save and exit (Automatically exits in 6 seconds if no operation detected).

Save and get back (Automatically exits if no operation detected in 6 seconds). Select the digit (The selected digit will flash). Set the number.

Common Wheel Size and Circumference (Wheel Size L (mm))

Time Zone Setting

1. Hold the > button to enter setting mode.
2. There are 5 settings pages available (P1-P5). Press > to switch to P3.
3. Press ►II to select to enter (Default time zone: UTC/GMT + 08:00).
4. Press ►II to select the setting digit, press > to set the numbers.
5. Press ⚙️ to save and exit (Automatically exits in 6 seconds if no operation detected).

Save and get back (Automatically exits if no operation detected in 6 seconds). Select the digit (The selected digit will flash). Set the number.

Setting Metric and Imperial Units

1. Hold the > button to enter setting mode.
2. There are 5 settings pages available (P1-P5). Press > to switch to P4.
3. Press ►II to enter (Default: KMH).
4. Press > to switch.
5. Press ⚙️ to save and exit (Automatically exits in 6 seconds if no operation detected).

Save and get back (Automatically exits if no operation detected in 6 seconds). Set the KMH/MPH.

Power Calibration

1. Hold the > button to enter setting mode.
2. There are 5 settings pages available (P1-P5). Press > to switch to P5; it will automatically calibrate.
3. Short press ►II to recalibrate. The value flashes during calibration and stops flashing after successful calibration.
4. After successful calibration, press ⚙️ to save and exit (Automatically exits in 20 seconds if no operation detected).

Save and get back (Automatically exits if no operation detected in 20 seconds). Recalibrate.

GPS Positioning

1. GPS searching is automatic after power on. Please start cycling after GPS positioning is successful.
2. If you start riding when GPS is not positioned successfully (speed sensor not connected), speed data (real-time, average, maximum) will be displayed as "--.--", and the rest of the data remains the same.
3. Tips: You can stand still for 3-5 minutes to get more connections with satellites for better GPS signal.

Signal Strength: No signal ?️, Weak ?, Normal ✔️, Strong ⭐

Display Indicators: No satellite signal ?️, No Speed data display "--.--"

Note: Please ensure you are outdoors when positioning. Bad weather and dense forests may affect GPS signal.

Cycling

Turn on the device and press ►II to start exercise and recording. During cycling, if the speed is 0, the device will pause automatically. If there is no data for speed, cadence, or heart rate for 15 minutes, the device will enter sleep mode. Press ►II to resume.

Button Actions:

• Press ►II: Mark a new lap.
• Press ►II: Pause/continue.
• Hold ►II: Stop exercise and save the riding data.
• Press >: Switch the display.

Bluetooth Connection

1. Download CoospoRide from Google Play or the App Store.

Compatible with:

• iOS 9.0 version and above, iPhone 4s and above.
• Any Bluetooth 4.0 enabled Android device with Android 4.3 and above.

Pairing with the CoospoRide App

1. Power on the bike computer.
2. Open the CoospoRide App, enter the binding computer step, and select the BC107 from the device list to bind the device. (The phone needs to have Bluetooth turned on and grant Bluetooth permissions).

Data Synchronization

1. In the App's activity page, click on the connected device to enter the record synchronization operation page. (Through authorization to Strava in the App's more settings, computer data can be synchronized to the Strava platform at the same time).
2. Select the record to be synchronized and click Sync. The record on the computer will be deleted automatically after synchronization.

Basic Parameters

Attentions

The water resistance level of the bicycle computer is IPX7. It can be used in the rain if you close the protective cover on the back tightly. It is recommended to take down the bicycle computer and put it into a waterproof bag if it rains heavily.

Responsibility Disclaimer

• The information contained in this manual is for reference only. The product described above may be subject to alteration due to the manufacturer's continuing research and development plans, without prior announcement.
• COOSPO shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or in connection with this manual or the contained product.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and .
2. This device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Recycling Information

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

Important Safety Information:

• Do not open or modify the product.
• Do not disassemble or attempt to service this product.
• This product is safe under normal and reasonably foreseeable operating conditions.
• If the product is operating improperly, call COOSPO support.
• Product must be returned to the manufacturer for any service or repair.