WAC RCUV-WT Smart Fan Remote Control
Brand: WAC Lighting
Model: RCUV-WT
1 Pairing
NOTE:
Pairing must be completed within three (3) minutes of turning the power ON to the fan receiver.
To pair your remote control:
- Power cycle your fan by removing power from the circuit breaker for 10 seconds and then re-enable power.
- Press and hold the [fan speed up] and [fan speed down] buttons on the remote control for 4-5 seconds.
- The LED will blink green.
- The green LED along with audible beeps will indicate that pairing is successful.
- Test remote control using the steps in section 2.
FIG.1 Description: Shows pressing and holding the [fan speed up] and [fan speed down] buttons on the remote control.
2 Remote Control Operation
NOTE:
On your fan, press the [mode switch button] while the fan is running.
Remote Control Button Functions:
- [light toggle button]: Turns the light ON or OFF.
- [fan toggle button]: Turns the fan ON or OFF.
- Press or hold the [fan speed up] button to increase fan speed.
- Press or hold the [fan speed down] button to decrease fan speed.
NOTE:
Your fan features 6 speeds. An audible tone will indicate when the speed is increased or decreased. When the fan has reached the minimum/maximum speed level, the fan will beep twice.
FIG.2 Description: Illustrates the remote control with labeled buttons: [light toggle button], [fan toggle button], [fan speed up], and [fan speed down].
3 UV Auto-Off Feature
This feature automatically turns off the UV light after a fixed period of time. The feature is off by default. To enable/disable, press and hold the [light toggle button] and [fan speed up] for 4 seconds. The fan will beep, indicating a change. Default time: 45 minutes. Duration can be changed using the App.
4 Breeze Mode
Breeze Mode mimics the natural ebb and flow of winds in nature by varying the fan speed.
NOTE:
Breeze Mode always rotates your fan in the Summer (Counter-Clockwise) direction.
- To start Breeze Mode, press the [fan speed up] and [fan speed down] buttons for 4 seconds. The LED will blink green and the fan will beep.
- To exit Breeze Mode and return to standard fan mode, press and hold the [fan speed up] and [fan speed down] buttons for 4 seconds. The LED will blink green and the fan will beep. Your fan will return to the direction and speed it was set to prior to entering Breeze Mode.
FIG.3 Description: Illustrates Summer Mode with downward airflow for cooling.
FIG.4 Description: Illustrates Winter Mode with upward airflow to redistribute warm air.
5 Unpairing
NOTE:
Unpairing must be completed within 3 minutes of turning the power on to the fan receiver.
- When you re-engage power to the fans you want to unpair, press and hold the [fan speed up] and [fan speed down] buttons for 4 seconds.
- The LED will blink green, and the receiver will beep to indicate that unpairing is successful.
FIG.5 Description: Shows pressing and holding the [fan speed up] and [fan speed down] buttons on the remote control.
6 UV End-of-Life Notification and Reset Procedure
The fan automatically tracks module usage. When there is approximately 10% life remaining, the user will be notified by the light module blinking in an on/off pattern for the first 10 seconds after turning it on. This is an indication the user should replace the module.
To reset the fan's internal counter, press and hold the [UV light] and [fan speed down] buttons for 4 seconds. The fan receiver will beep short-long-short to indicate the reset was successful.
7 Fan Wi-Fi Reset
NOTE:
This function only resets the Wi-Fi settings.
- Press and hold the [fan speed up] and [fan speed down] buttons for 10 seconds.
- The LED will blink green and the receiver will beep to indicate that Wi-Fi reset is successful.
After the Wi-Fi resets, the fan will broadcast its factory set network name beginning with "WACFan."
NOTE:
Changes to your Wi-Fi network settings (SSID or Security Passphrase) will prevent your fan from connecting to the cloud. You can re-establish connectivity by performing a Wi-Fi Reset and using the WAC Smart Fans app to reconfigure the fan to connect to the network with the new settings.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Wangs Alliance Corporation is under license. Other trademarks and trade names are those of their respective owners.
8 Factory Reset
Using remote control
Remote Control Factory Reset:
- Press and hold the [light toggle button], [fan toggle button], and [fan speed up] buttons for 10 seconds.
- The LED will blink green and the receiver will beep to indicate that the factory reset is successful.
NOTE:
This will remove remote control(s), wall control(s), and WAC Smart Fans app connections.
9 Replacing the Batteries
Steps:
- Open the back of the remote with a flat screwdriver.
- Remove the back of the remote and put it aside.
- Remove the old batteries from the remote.
- Insert your new CR2032 batteries into the remote.
- Push in the back of the remote, making sure it locks into place.
- You are now ready to control your fan.
Diagram Description: A sequence of five steps illustrating the process of opening the remote, removing old batteries, inserting new CR2032 batteries, and reassembling the remote.
Package Contents
The package typically includes:
- Remote Control
- Wall Cradle
- Screws
- CR2032 Batteries
Rules and Regulations
CAUTION:
The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Compliance:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: THIS PRODUCT EMITS ULTRAVIOLET (UV) RADIATION.
Exposure to UV radiation can cause serious personal injury, including damage to eyes and skin. Avoid direct exposure to the UV light. Do not operate the product while anyone could be directly exposed to the UV light. For more safety instructions, please refer to the instruction manual.
FCC Supplier's Declaration of Conformity
Brand name: WAC Lighting
Model number: RCUV-WT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WAC LIGHTING
44 Harbor Park Drive, Port Washington, NY 11050
Tel: 1-866-810-6615
WARNING: Chemical Burn Hazard.
Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
