Anko

Product Details

Keycode: K: 43589029

Model/Reference: T: 71286273, F: KT07-741-200

Contents:

• A Tree Top
• B Upper Body
• C Lower Body
• D Metal Stand

Assembly Instructions

Please read through these instructions thoroughly before use and retain for future reference.

Diagram Descriptions:

• Diagram A shows the tree top section.
• Diagram B shows the upper body section.
• Diagram C shows the lower body section.
• Diagram D illustrates the metal stand being unfolded.
• Diagram E depicts attaching the tree top (A) to the upper body (B) and connecting the power plug.
• Diagram F illustrates inserting the lower body (C) into the metal stand (D).
• Diagram G shows the tree fully assembled, with instructions to open and shape the branches.
• Diagram H shows the power supply (adaptor) and its connection to the tree lights.

Steps:

1. Before starting assembly, place the tree stand on a level surface and unfold the metal stands, ensuring they are perpendicular to each other.
2. Insert the bottom section (C) into the stand using the provided screws, making sure it is tightly secured.
3. Insert the middle section (B) into the pole of the bottom section (C). Note: Different tree sizes may contain several middle sections.
4. Insert the tree top (A) into the trunk and ensure the tab fits tightly into the slot in the tree trunk.
5. Open all branches. Shape the branches, starting with tips farthest from the pole, directing one to the right, one to the left, and one at the center of the main stem.
6. Wrap the end tip of each branch around the wire near the pole.
7. After shaping the entire tree, step back to get an overall look. Shift branches to fill any gaps and slightly upsweep all branch tips for a natural look.
8. Connect the light set to the provided connector(s) and plug the connector into the adaptor, then plug the adaptor into the power outlet.
9. Connect the male and female plugs by locating the matching color coding label.

Disassembly and Storage Tips

1. Save the original carton for storage.
2. Unplug the adaptor from the wall outlet and remove all ornaments and decorations.
3. Disassemble the tree by reversing the assembly steps. Do not detach factory pre-plugged light sets.
4. If tree pole sections are difficult to separate, apply a small amount of lubricant at the joint and rotate the upper pole in both directions before lifting it again.
5. Gently press branches against the stem while removing sections from top to bottom.
6. Carefully replace the tree in its box, tape it shut, and store the carton in a cool, dry place.
7. Do not place the tree directly under sunlight or in a damp area, or in areas where the temperature exceeds 40°C (90°F).
8. Please save these instructions for future reference.

Installation and Instructions

1. This tree is suitable for INDOOR USE only.
2. The adaptor MUST be installed INDOORS, away from weather.
3. Do not position or place the tree near heaters or any other direct sources of heat.
4. This product is suitable for positioning on surfaces with normal flammability, e.g., wood, plastic board, masonry. However, this does not include highly flammable surfaces (e.g., polystyrene, textiles).
5. Always position cables and extension leads so that they will not be a hazard to the elderly, pets, and children.
6. DO NOT position this set where it may become covered by other items, e.g., curtains, nets, or bedding.
7. Ensure the unit(s) is positioned so that you have enough cable to reach an indoor mains power socket.
8. The external flexible cable or cord of this luminaire cannot be replaced. If the cord is damaged, the luminaire shall be destroyed.
9. Do not connect the tree to the supply while it is in the packaging.
10. Maximum lighting chains to be connected is 3. The system wattage is 3.6W after all 3 are connected.
11. For lighting chains intended for interconnection: "Do not interconnect parts of this lighting chain with parts of another manufacturer's lighting chain." "Interconnection shall be made only by the use of the supplied connectors. Any open ends must be sealed-off before use."

Warnings:

• Do not try to remove these non-replaceable bulbs.
• This product is NOT designed for permanent or long-term use.
• The supplied adaptor is suitable for operation of LED Modules only.
• Only operate this light set with the supplied adaptor, Model No. JT-DC31V3.6W-H5.
• Do not connect this tree electrically to another tree.
• Do not connect this tree to the power supply while it is in the packaging.
• If any part of the light set or cable is damaged, the light set MUST be discarded.
• This product is for use as a decoration only. Not to be used by children as a toy. Keep out of reach of children.
• Always switch off this light set or unplug an adaptor if unattended.
• DO NOT overload power sockets or extension leads.
• DO NOT pierce the cable when sourcing in place, bend or stand on the tree, as this will damage the bulbs or wiring.
• Please refer to the packing or product rating label for product class, specifications, and rating.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire shall be replaced.
• Do not allow interconnect to light chain other than supplied set.

LED Bulbs

This light set is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the light set.

AC Adaptor (Do Not Cover) Warning

LED Driver (AC Adaptor) Manual:

1. Do not open the cover of the equipment.
2. For use with LED lighting equipment only.
3. The input and output voltage should be checked before use to ensure correct use.
4. This is the Class II product, only for indoor use.
5. The product is not a toy; keep it where children cannot reach.
6. The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental contact with with live parts.
7. If applicable, an indication that the controlgear is suitable for operation with LED modules will be present.
8. This unit has a "Do-not-cover" classification.

Power Supply Clearance: The power supply (LED Drive) can be used near normally flammable materials, including building insulation, but cannot be abutted against any material and cannot be covered in normal use. A minimum clearance distance of 75 mm is required from the top and sides of the control gear to any normally flammable building element. This is illustrated in a diagram showing a combustible building structural member and a combustible building element above the fitting, with clearance distances labeled A, B, and C, all indicating a minimum of 75 mm. A barrier is required for loose fill insulation or loose combustible materials.

Made in China