Power Dynamics BC Series In/Outdoor Speaker Set 100V

Introduction

Congratulations on your purchase of this Power Dynamics product. Please read this manual thoroughly prior to using the unit to benefit fully from all features.

Important Safety Precautions

Read the manual before use. Follow instructions to avoid invalidating the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician.

• Before use, consult a specialist. A slight smell may occur upon first use, which is normal and will disappear.
• The unit contains voltage-carrying parts; do NOT open the housing.
• Do not place metal objects or pour liquids into the unit; this may cause electrical shock and malfunction.
• Do not place the unit near heat sources (e.g., radiators) or on vibrating surfaces. Do not cover ventilation holes.
• The unit is not suitable for continuous use.
• Do not plug or unplug with wet hands.
• If the plug or mains lead is damaged, it must be replaced by a qualified technician.
• If the unit is damaged and internal parts are visible, do NOT plug it into a mains outlet or switch it on. Contact your dealer.
• Do NOT connect the unit to a rheostat or dimmer.
• To avoid fire and shock hazard, do not expose the unit to rain and moisture.
• All repairs should be carried out by a qualified technician only.
• During thunderstorms or if the unit will not be used for an extended period, unplug it from the mains. Unplug when not in use.
• If the unit has been stored for a long time, condensation may occur. Allow the unit to reach room temperature before switching it on.
• In commercial settings, follow applicable guidelines and instructions.
• Do not repeatedly switch the unit on and off; this shortens its lifespan.
• Keep the unit out of reach of children. Do not leave the unit unattended.
• Do not use cleaning sprays on switches; residues can cause dust and grease deposits.
• In case of malfunction, always seek advice from a specialist.
• Do not force controls.
• This unit contains a speaker that can generate a magnetic field. Keep it at least 60cm away from computers or TVs.
• If the unit has been dropped, have it checked by a qualified technician before switching it on again.
• Do not use chemicals for cleaning; they can damage the finish. Clean only with a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Use only original spare parts for repairs to avoid serious damage or dangerous radiation.
• Switch the unit off before unplugging it from the mains or other equipment. Unplug all leads and cables before moving the unit.
• Keep original packing material for safe transport.

⚡️ This mark indicates the presence of high voltages inside the housing, sufficient to cause a shock hazard.

⚠️ This mark highlights important instructions in this manual that should be read and followed.

The unit is CE certified. Modifications are prohibited and will invalidate the CE certificate and warranty.

Note: For normal operation, the unit requires room temperatures between 5°C/41°F and 35°C/95°F.

Electric products should not be disposed of with household waste. Please return them to a recycling center. Contact local authorities or your dealer for disposal procedures. Specifications are typical and may vary slightly between units. Specifications are subject to change without prior notice.

Do not attempt self-repairs or modifications, as this will invalidate your warranty. Power Dynamics is not responsible for personal injuries or damages resulting from misuse or failure to follow safety recommendations and warnings.

Basic Connections

Use the switch on the back of the speaker to choose the output. The speakers can be used with either 8 Ohm or 100 Volt line systems.

Connection Examples

Standard 100V Line

Example: 4 x 20W load = 80W total load.

Diagram Description: An amplifier is connected to four speakers in series, each rated at 20W. The total load is 80W.

Multi-tap 100V Line

Example: 20W + 10W + 10W + 2W + 2W + 4W load = 48W total load.

Diagram Description: An amplifier is connected to multiple speakers with different wattage taps (20W, 10W, 10W, 2W, 2W, 4W) in series. The total load is 48W.

8 Ohm Examples

Standard 8 Ohm Loudspeaker Setup

Diagram Description: An amplifier is connected to two 8 Ohm speakers in parallel.

Parallel 4 Loudspeaker Setup

Diagram Description: An amplifier is connected to four 8 Ohm speakers in parallel.

Series Parallel 4 Loudspeaker Mono Setup

Diagram Description: An amplifier is connected to four 8 Ohm speakers arranged in a series-parallel configuration.

How to Connect Your Speakers

1. Ensure the audio system is turned off before making any connections.
2. Connect the speaker(s) to the amplifier output. Use the black wire for the negative pole and the red wire for the positive pole. (Refer to connection terminal 2 on the speaker diagram).
3. Adjust the rotary switch (1) on the speaker to the desired 100 Volt or 8 Ohm position. The 8 Ohm position is for directly operating the speaker at a low-impedance amplifier output.
4. When connecting multiple speakers, ensure all speakers have the same polarity and that the amplifier is not overloaded.

Speaker Diagram Description: The speaker features a front grille covering the woofer and tweeter. On the rear, there is a rotary switch (labeled 1) for selecting the impedance/voltage setting (e.g., OFF, 5W, 10W, 25W) and connection terminals (labeled 2) for positive and negative speaker wire connections.

Technical Specifications

The specifications are typical. Actual values may vary slightly between units. Specifications are subject to change without prior notice.

Compliance

The products referred to in this manual conform to the following European Community Directives:

• Low Voltage (LVD) 2014/35/EU
• Electromagnetic Compatibility (EMC) 2014/30/EU
• Restriction of Hazardous Substances (RoHS) 2011/65/EU

CE