Important Safety Instructions
Please save these instructions.
WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.
CAUTION: Indicates a critical procedure for safe and proper operation of the system.
NOTE: Indicates a procedure or function that is important to the safe and proper operation of the system.
General Safety Information
- Read all of the instructions and cautions in the manual before beginning the installation.
- Installation should be completed by a professional contractor to avoid damages that may be incurred due to improper sealing.
- Do NOT substitute parts from other manufacturer sources; doing so may void the warranty and/or result in an unstable system.
- This system does NOT possess any compliance with residential structural codes and should not be used in place of a system that is, if so required by local regulations.
Installer Responsibilities
- Installation compliance with any applicable codes which are in force at the installation site.
- Installation compliance and compatibility with all system components and the environment, including but not limited to roofing, system components, etc.
- Verification that all project information is accurate.
General Information
The Renogy Corner Bracket Mount (MTS-CB) provides drill-free and secure mounting for virtually any aluminum-framed solar panels onto flat surfaces. The MTS-CB elevates the solar panel to an optimal height, creating an air gap that enhances panel output performance. Additionally, the mounts function as a wind deflector while maintaining this air gap. The MTS-CB facilitates a cleaner and more flexible installation process on most motorhomes, caravans, or boats.
Key Features
- Non-corrosive, long-lasting, high-quality ABS plastic construction.
- 100% recyclable and UV resistant.
- Drill-free mounting.
- Designated for virtually any aluminum-framed solar panels.
- Best suited for flat roofs of smooth aluminum, wood, or GRP material.
- Easier and more flexible installation.
- Compatible with all Renogy solar panels.
Identification of Components
| Part | Quantity |
|---|---|
| Corner Bracket | 4 |
| Side Bracket | 2 |
Diagram shows a corner bracket and a side bracket.
Installation
NOTE: These instructions serve as a simple guideline for installing the corner bracket mounts. Actual installations may vary with adhesive type or roof type. Consult your adhesive manufacturer for proper instructions regarding ABS plastic and your specific roof material.
Recommended tools to have before installation:
- Assembly Adhesive (e.g., Sikaflex-252)
- Caulking gun
- Masking Tape
- Hand Pads (e.g., Scotchbrite Pads)
- Spirit Level
- Tape Measure
WARNING: Assembly adhesives contain hazardous chemicals that can be detrimental to one's health. Ensure adherence to the manufacturer's handling and care instructions when using assembly adhesives.
1. Mate Corner Brackets to Solar Panel
- Apply adhesive to the top side of the corner bracket where the panel will be installed.
- Match the corner bracket to the solar panel corner.
- Apply pressure to ensure proper contact.
- Repeat for the other 3 corner brackets.
NOTE: Adhere to adhesive manufacturer specifications for application and drying time.
Diagram shows a corner bracket being positioned onto a solar panel corner, with green arrows indicating adhesive application points.
2. Mate Side Bracket to Solar Panel
- Apply adhesive to the top side of the side bracket where the panel will be installed.
- Place the side bracket onto the solar panel side. Adjust for symmetry as needed.
- Apply pressure to ensure proper contact.
- Repeat for the other side.
NOTE: Adhere to adhesive manufacturer specifications for application and drying time.
Diagram shows a side bracket being positioned onto a solar panel side, with green arrows indicating adhesive application points. A subsequent diagram shows the solar panel with four corner brackets and two side brackets attached.
3. Apply Adhesive to the Brackets and Install on Flat Surface
NOTE: Always mark the intended location of the solar panel on the flat surface before proceeding to apply adhesive.
NOTE: Ensure the proper solar panel orientation so that the wires exit from the user's desired side.
- Clean the surface of the brackets and the flat surface to ensure maximum bonding potential.
- Apply adhesive to the bottom side of all brackets where they will contact the flat mounting surface.
- Apply pressure to ensure proper contact.
NOTE: Adhere to adhesive manufacturer specifications for application and drying time.
Diagram shows green arrows indicating adhesive application points on the bottom of the brackets. A subsequent diagram shows the solar panel, now mounted with brackets, resting on a flat surface.
Technical Specifications
| Parameter | Specification |
|---|---|
| Material | UV-resistant ABS Plastic |
| Weight (each component) | 7.2 oz. |
| Side Bracket Dimensions (L x W x H) | 7.0 x 4.6 x 2.3 in |
| Corner Bracket Dimensions (L x W x H) | 5.9 x 5.9 x 2.3 in |
| Recommended Adhesive | Sikaflex 252 or alike |
Compatibility
The MTS-CB mounts are compatible with all Renogy solar panels, excluding the solar suitcase models.
Dimensions
Note: The following drawings utilize inches as their dimension units.
Side Bracket
Diagram shows the top and side views of the side bracket with dimensions labeled: Length 7.00 in, Width 4.60 in, Height 2.30 in. Other dimensions shown include 1.05 in, 1.00 in, and 0.20 in.
Corner Bracket
Diagram shows the top and side views of the corner bracket with dimensions labeled: Length 5.91 in, Width 5.91 in, Height 2.30 in. Other dimensions shown include 4.96 in, 3.39 in, and 0.19 in.
