Renogy MTS-CB Corner Bracket Mount
Renogy
2775 E Philadelphia St, Ontario, CA 91761
1-800-330-8678
Version: 1.0
Important Safety Instructions
Please save these instructions.
Safety Symbols
⚠️ WARNING
Indicates a potentially dangerous condition. Use extreme caution when performing this task.
⚠️ CAUTION
Indicates a critical procedure for safe and proper operation of the system.
ℹ️ NOTE
Indicates a procedure or function that is important to the safe and proper operation of the system.
General Safety Information
- Read all of the instructions and cautions in the manual before beginning the installation.
- Installation should be completed by a professional contractor to avoid damages that may be incurred due to improper sealing.
- Do NOT substitute parts from other manufacturer sources; doing so may void the warranty and/or result in an unstable system.
- This system does NOT possess any compliance with residential structural codes and should not be used in place of a system that is, if so required by local regulations.
Installer Responsibilities
- Installation compliance with any applicable codes which are in force at the installation site.
- Installation compliance and compatibility with all system components and the environment, including but not limited to roofing, system components, etc.
- Verification that all project information is accurate.
General Information
The Renogy Corner Bracket Mount (MTS-CB) can be used with virtually any aluminum-framed solar panels to provide drill-free and secure mounting to flat surfaces. The MTS-CB raises the solar panel to an optimum height that establishes an air gap, improving panel output performance. Additionally, the mounts act as a wind deflector while maintaining the air gap. With the MTS-CB, installation is cleaner and more flexible on most motorhomes, caravans, or boats.
Key Features
- Non-corrosive, long-lasting, and high-quality ABS plastic construction.
- 100% recyclable and UV resistant.
- Drill-free mounting.
- Designated for virtually any aluminum-framed solar panels.
- Best suitable for flat roofs of smooth aluminum, wood, or GRP material.
- Easier and more flexible installation.
- Compatible with all Renogy solar panels.
Identification of Components
| Part | Quantity |
|---|---|
| Corner Bracket | 4 |
| Side Bracket | 2 |
Image of two Renogy MTS-CB corner brackets.
Diagram showing a Corner Bracket and a Side Bracket with their respective shapes.
Installation
Installation Notes
- These instructions serve as a simple guideline for installing the corner bracket mounts. Actual installations may vary with adhesive type or roof type. Consult your adhesive manufacturer for proper instructions of ABS plastic to a user-defined roof material.
Recommended Tools
- Assembly Adhesive (Sikaflex-252)
- Caulking gun
- Masking Tape
- Hand Pads (Scotchbrite Pads)
- Spirit Level
- Tape Measure
Safety Warning for Adhesives
⚠️ WARNING
Assembly adhesives contain hazardous chemicals that can be detrimental to one's health. Make sure to abide by the manufacturer's handling and care when using assembly adhesives.
Step 1: Mate Corner Brackets to Solar Panel
- Apply adhesive to the top side of the corner bracket where the panel will be installed.
- Match corner bracket to solar panel corner.
- Apply pressure to ensure proper contact.
- Repeat for the other 3 corner brackets.
ℹ️ NOTE
Adhere to adhesive manufacturer specifications for application and time to dry.
Diagram illustrating the application of adhesive to a corner bracket, with arrows indicating placement on a solar panel corner.
Diagram showing a solar panel with four corner brackets attached, viewed from above.
Step 2: Mate Side Bracket to Solar Panel
- Apply adhesive to the top side of the side bracket where the panel will be installed.
- Place side bracket to solar panel side. Adjust for symmetry as needed.
- Apply pressure to ensure proper contact.
- Repeat for the other side.
ℹ️ NOTE
Adhere to adhesive manufacturer specifications for application and time to dry.
Diagram illustrating the application of adhesive to a side bracket, with arrows indicating placement on a solar panel side.
Diagram showing a solar panel with corner and side brackets attached, ready for surface mounting.
Step 3: Apply Adhesive to Brackets and Install on Flat Surface
ℹ️ NOTE
Always mark out where the solar panel will be located on the flat surface before proceeding to apply adhesive.
ℹ️ NOTE
Ensure the proper solar panel orientation so that the wires are coming out of the user desired side.
- Clean the surface of the brackets and of the flat surface to ensure maximum bonding potential.
- Apply adhesive to the bottom side of all the brackets where they will make contact with the flat mounting surface.
- Apply pressure to ensure proper contact.
ℹ️ NOTE
Adhere to adhesive manufacturer specifications for application and time to dry.
Diagram showing the solar panel with attached brackets being placed onto a flat mounting surface, with arrows indicating alignment.
Diagram showing the solar panel with attached brackets mounted on a flat surface.
Technical Specifications
| Parameter | Specification |
|---|---|
| Material | UV-resistant ABS Plastic |
| Weight (each component) | 7.2 oz. |
| Side Bracket Dimensions (l x w x h) | 7.0 x 4.6 x 2.3 in |
| Corner Bracket Dimensions (l x w x h) | 5.9 x 5.9 x 2.3 in |
| Recommended Adhesive | Sikaflex 252 or alike |
Compatibility
The MTS-CB mounts are compatible with all Renogy solar panels excluding the solar suitcase models.
Dimensions
ℹ️ Note
The following drawings utilize inches as their dimension units.
Side Bracket
Diagram showing the dimensions of the Renogy MTS-CB Side Bracket.
Corner Bracket
Diagram showing the dimensions of the Renogy MTS-CB Corner Bracket.
