Renogy MTS-CB Corner Bracket Mount
Model: MTS-CB
Version: 1.0
Manufacturer: Renogy
Address: 2775 E Philadelphia St, Ontario, CA 91761
Phone: 1-800-330-8678
Important Safety Instructions
▲ WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.
CAUTION: Indicates a critical procedure for safe and proper operation of the system.
NOTE: Indicates a procedure or function that is important to the safe and proper operation of the system.
General Safety Information
- Read all instructions and cautions before installation.
- Installation should be completed by a professional contractor to avoid damages from improper sealing.
- Do NOT substitute parts from other manufacturers, as this may void the warranty and/or result in an unstable system.
- This system does NOT possess compliance with residential structural codes and should not be used in place of a system that is, if required by local regulations.
Installer Responsibilities
- Ensure installation compliance with all applicable codes at the installation site.
- Ensure installation compliance and compatibility with all system components and the environment, including roofing and system components.
- Verify that all project information is accurate.
General Information
The Renogy Corner Bracket Mount (MTS-CB) is designed for use with virtually any aluminum-framed solar panels, providing drill-free and secure mounting to flat surfaces. The MTS-CB elevates the solar panel to an optimal height, creating an air gap that enhances panel output performance. Additionally, the mounts function as a wind deflector while maintaining this air gap. The MTS-CB facilitates a cleaner and more flexible installation on most motorhomes, caravans, and boats.
Key Features
- Non-corrosive, long-lasting, high-quality ABS plastic construction.
- 100% recyclable and UV resistant.
- Drill-free mounting system.
- Designed for virtually any aluminum-framed solar panels.
- Best suited for flat roofs made of smooth aluminum, wood, or GRP material.
- Offers easier and more flexible installation.
- Compatible with all Renogy solar panels.
Identification of Components
The mounting kit includes the following components:
| Part | Description | Quantity |
|---|---|---|
| Corner Bracket | A 3D representation of an L-shaped bracket, typically black, designed to attach to the corner of an aluminum solar panel frame. It features a base with holes or indentations for adhesive application and a raised lip that conforms to the panel's frame. | 4 |
| Side Bracket | A 3D representation of a T-shaped bracket, typically black, designed to attach along the side of an aluminum solar panel frame. It has a base with holes or indentations for adhesive application and a raised lip that conforms to the panel's frame. | 2 |
Installation
NOTE: These instructions serve as a simple guideline for installing the corner bracket mounts. Actual installations may vary based on adhesive type or roof type. Consult your adhesive manufacturer for proper instructions regarding ABS plastic application to a user-defined roof material.
Recommended Tools
- Assembly Adhesive (e.g., Sikaflex-252)
- Caulking gun
- Masking Tape
- Hand Pads (e.g., Scotchbrite Pads)
- Spirit Level
- Tape Measure
WARNING: Assembly adhesives contain hazardous chemicals that can be detrimental to health. Ensure adherence to the manufacturer's handling and care instructions when using assembly adhesives.
Step 1: Mate Corner Brackets to Solar Panel
- Apply adhesive to the top side of the corner bracket where the panel will be installed.
- Align the corner bracket with the solar panel corner.
- Apply pressure to ensure proper contact.
- Repeat for the other three corner brackets.
NOTE: Adhere to the adhesive manufacturer's specifications for application and drying times.
Diagram Description: A diagram shows a solar panel corner and a corner bracket being positioned with green arrows indicating attachment. Another diagram shows a solar panel from a top-down view with four corner brackets attached to its corners.
Step 2: Mate Side Bracket to Solar Panel
- Apply adhesive to the top side of the side bracket where the panel will be installed.
- Place the side bracket onto the solar panel side. Adjust for symmetry as needed.
- Apply pressure to ensure proper contact.
- Repeat for the other side.
NOTE: Adhere to the adhesive manufacturer's specifications for application and drying times.
Diagram Description: A diagram shows a solar panel side and a side bracket being positioned with green arrows indicating attachment. Another diagram shows a solar panel from a top-down view with four corner brackets and two side brackets attached along its longer sides.
Step 3: Apply Adhesive to Brackets and Install on Flat Surface
NOTE: Always mark out where the solar panel will be located on the flat surface before proceeding to apply adhesive.
NOTE: Ensure the proper solar panel orientation so that the wires are coming out of the user-desired side.
- Clean the surface of the brackets and the flat surface to ensure maximum bonding potential.
- Apply adhesive to the bottom side of all brackets where they will make contact with the flat mounting surface.
- Apply pressure to ensure proper contact.
NOTE: Adhere to the adhesive manufacturer's specifications for application and drying times.
Diagram Description: Diagrams show a solar panel with brackets attached, viewed from the underside with green arrows indicating adhesive application points. Another diagram shows the solar panel with brackets installed on a flat surface, viewed from an isometric perspective.
Technical Specifications
| Parameter | Specification |
|---|---|
| Material | UV-resistant ABS Plastic |
| Weight (each component) | 7.2 oz. |
| Side Bracket Dimensions (l x w x h) | 7.0 x 4.6 x 2.3 in |
| Corner Bracket Dimensions (l x w x h) | 5.9 x 5.9 x 2.3 in |
| Recommended Adhesive | Sikaflex 252 or alike |
Compatibility
The MTS-CB mounts are compatible with all Renogy solar panels, excluding the solar suitcase models.
Dimensions
NOTE: The following drawings utilize inches as their dimension units.
Side Bracket
Diagram Description: Orthographic views (front and side) of the Side Bracket with dimension lines and numerical values indicating length, width, and height. The front view shows dimensions 7.00 (length), 4.60 (height), 1.05 (base thickness), 2.30 (overall height). The side view shows 1.00 (width), 0.20 (base thickness).
Corner Bracket
Diagram Description: Orthographic views (front and side) of the Corner Bracket with dimension lines and numerical values indicating length, width, and height. The front view shows dimensions 5.91 (length/width), 4.96 (height), 3.39 (inner corner length). The side view shows 2.30 (height), 0.19 (thickness).
