VIGO Elan Frameless Sliding Shower Door Installation Guide
Model: VG6041MGCL6474
Finish: Matte Gold
Dimensions: 64 in. x 74 in.
Important Safety Information
Read all instructions carefully before beginning installation.
- Two people are recommended for installation.
- Ensure the wall studs are plumb and level.
- Do not overtighten screws, as this may damage the glass or frame.
- Handle glass panels with care to avoid breakage.
- Wear safety glasses and gloves during installation.
- Check local building codes for specific requirements.
Parts List
[Diagram: Illustration showing all included parts with labels corresponding to the list below.]
- (A) Fixed Panel Frame (1)
- (B) Sliding Panel Frame (1)
- (C) Top Guide Rail (1)
- (D) Bottom Track (1)
- (E) Wall Mount Brackets (2)
- (F) Anti-Jump Device (2)
- (G) Roller Assemblies (2)
- (H) Door Handle (1)
- (I) Seal Strips (various)
- (J) Mounting Hardware Kit (screws, anchors, etc.)
- (K) Template (1)
Tools Required (Not Included)
- Measuring Tape
- Pencil
- Level
- Drill with appropriate drill bits
- Screwdriver (Phillips head)
- Caulking Gun
- Clear Silicone Sealant
- Utility Knife
- Safety Glasses
- Work Gloves
Installation Steps
Step 1: Prepare the Opening
Measure the shower opening to confirm dimensions. Use the provided template (K) to mark the positions for the wall mount brackets (E) and bottom track (D). Ensure all marks are level and plumb.
[Diagram: Marking the wall and tub/shower base using the template.]
Step 2: Install Wall Mount Brackets
Drill pilot holes at the marked locations. Secure the wall mount brackets (E) to the wall studs using the appropriate screws from the hardware kit (J). Ensure brackets are firmly attached and level.
[Diagram: Attaching wall mount brackets to the wall.]
Step 3: Install Bottom Track
Apply a bead of silicone sealant along the bottom edge of the bottom track (D). Position the track onto the shower base/tub ledge according to the marked lines. Secure the track using screws from the hardware kit (J) through the pre-drilled holes into the base or wall if applicable.
[Diagram: Installing the bottom track with sealant and screws.]
Step 4: Install Top Guide Rail
Attach the top guide rail (C) to the wall mount brackets (E) using the provided hardware. Ensure the rail is level and securely fastened.
[Diagram: Mounting the top guide rail.]
Step 5: Attach Roller Assemblies to Sliding Panel
Install the roller assemblies (G) onto the sliding panel frame (B) as indicated. Attach the anti-jump devices (F) to the top of the sliding panel frame.
[Diagram: Attaching rollers and anti-jump devices to the sliding door panel.]
Step 6: Hang Sliding Door
Carefully lift the sliding door panel (B) with attached rollers (G) and hook the rollers onto the top guide rail (C). Ensure the door hangs straight. Adjust the rollers if necessary.
[Diagram: Hanging the sliding door onto the top rail.]
Step 7: Install Fixed Panel Frame
Attach the fixed panel frame (A) to the wall mount brackets (E) and the bottom track (D) using the provided hardware. Ensure it is plumb and securely fastened.
[Diagram: Installing the fixed panel frame.]
Step 8: Install Door Handle and Seals
Attach the door handle (H) to the sliding door panel (B). Install the seal strips (I) onto the edges of the glass panels and between the sliding and fixed panels for water containment.
[Diagram: Installing the handle and seal strips.]
Step 9: Adjust and Test
Check that the sliding door operates smoothly. Adjust the rollers and anti-jump devices (F) as needed to ensure proper operation and prevent the door from jumping off the track. Test the seals for water tightness.
[Diagram: Testing the door's movement and seals.]
Step 10: Final Sealing
Apply a bead of clear silicone sealant along the edges where the fixed panel frame and bottom track meet the wall and base, respectively. Smooth the sealant with a wet finger or tool. Allow sealant to cure according to manufacturer instructions before use.
[Diagram: Applying final silicone sealant.]
Care and Maintenance
Clean the glass and metal components regularly with a soft, damp cloth and mild soap. Avoid abrasive cleaners or harsh chemicals that could damage the finish or glass.
Periodically check that all hardware is tight and that the door operates smoothly.
Contact Information
For questions or assistance, please contact VIGO Industries customer support.
Visit the VIGO website for more product information and support resources.
