YITAHOME

Notice

1. Follow the installation instructions. Please confirm all accessories are preset before installation.

2. Do not fully tighten the screws during initial assembly. Fully tighten screws only once all pieces which are correctly assembled.

3. If you encounter any problems during installation, please contact our customer service.

Parts List

• 1: Lower shelf panel (x1)
• 2: Lower shelf panel (x1)
• 3: Tabletop (x1)
• 4: Side support panel (x1)
• 5: Side support panel (x1)
• 6: Back support panel (x1)
• 7: Front support panel (x1)
• 8: Side panel (x1)
• 9: Divider panel (x1)
• 10: Base frame component (x2)
• 11: Base support bar (x4)

Hardware List

• A: M4x8 screws (x8)
• B: M7x50 screws (x10)
• C: M7x70 screws (x8)
• D: M6x30 screws (x9)
• F: M6x40 screws (x8)
• H: M3.5x14 screws (x4)
• L: Allen wrench (x1)
• M: M5x10 screws (x12)
• N: Cam locks (x12)
• O: LED light strip connector (x5)
• P: Small screws (M3.5x14) (x4)
• R: Bracket (x1)
• S: LED light strip (x1)
• T: Hinge (x10)
• X: Mounting bracket (x4)
• Y: M8 screws (x4)

Assembly Steps

Step 1

Attach two base frame components (10) to each other using four 'Y' screws. Ensure correct orientation.

• Parts: 10 (x2), Y (x4)

Step 2

Attach four base support bars (11) to the two base frame components (10) using eight 'H' screws. Pay attention to the orientation of the holes.

• Parts: 10 (x2), 11 (x4), H (x8)

Step 3

Attach the lower shelf panel (2) to the assembled base structure using six 'F' screws.

• Parts: 2 (x1), F (x6)

Step 4

Attach the front support panel (7) and side panel (8) to the structure using eight 'A' screws. Ensure the panels are correctly aligned with pre-drilled holes.

• Parts: 7 (x1), 8 (x1), A (x8)

Step 5

Attach side support panels (4 and 5) to the front support panel (7) and side panel (8) using eight 'C' screws.

• Parts: 4 (x1), 5 (x1), 7 (x1), 8 (x1), C (x8)

Step 6

Attach the lower shelf panel (1) to the structure using seven 'B' screws.

• Parts: 1 (x1), B (x7)

Step 7

Attach the divider panel (9) to the structure using three 'B' screws.

• Parts: 9 (x1), B (x3)

Step 8

Secure the structure by attaching three 'D' screws and three 'F' screws into designated points.

• Parts: D (x3), F (x3)

Step 9

Attach the hinges (T) to the tabletop (3) using ten 'T' screws. Attach the bracket (R) and Allen wrench (L) to the tabletop as shown.

• Parts: 3 (x1), T (x10), R (x1), L (x1)

Step 10

Attach the tabletop assembly (3) to the main body using twelve 'N' cam locks. Ensure the lifting mechanism is properly aligned with the side panels.

• Parts: 3 (x1), N (x12), L (x1)

Step 11

Install the LED light strip (S). Remove protective tape from the light strip. Connect the light strip to the power box (M) and infrared receiver (O). The infrared receiver must be placed in front to receive signals from the remote. The battery box requires additional batteries (not included) and connects via USB. Route the light strip through designated holes in the boards.

• Parts: S (x1), M (x1), O (x5)

Step 12

Attach the mounting brackets (X) to the underside of the tabletop using four 'P' screws.

• Parts: X (x4), P (x4)

Step 13

Place the tempered glass panel (6) into the designated slots on the tabletop. After the glass is in place, tighten the fixing screws.

• Parts: 6 (x1)

Step 14

Final assembly check. Ensure all screws are fully tightened and the table is stable.

• Parts: All