ANDTE Home Dehumidifier User Manual

Welcome

Thanks for choosing ANDTE dehumidifier!

ANDTE is dedicated to keeping people healthy, comfortable and more enjoyable by offering quality appliances ranging from dehumidifiers to ice makers, and more. From breathing easier in your office to upgrading your kitchen appliances, we hope ANDTE could help you every step of the way.

READ THIS MANUAL INSTRUCTION CAREFULLY BEFORE USING THE UNIT. PLEASE KEEP THIS FOR FUTURE REFERENCE.

ANDTE PD161A home dehumidifier reduces humidity to comfortable levels in a short period of time. This dehumidifier has a sturdy housing to withstand harsh environments, is safe and easy to use, guarantees long-term use and easy maintenance, plus we use a copper tube condenser and high quality and accurate sensors, it will be more effective and last longer.

Before plugging in your new dehumidifier, we suggest that you read this user manual as it contains important safety information, operation instructions, troubleshooting, maintenance tips, and warranty information to ensure the reliability and longevity of your dehumidifier.

We're always just an email away

To access customer support, please email to AndteServices@outlook.com with your purchase order.

Thank you again!

Before First Use

Please leave the dehumidifier sitting outside the box for 24 HOURS before plugging it in.

The dehumidifiers may have been tilted or placed upside down during shipping. Leave the dehumidifier sits for 24 hours so the oil in the compressor can settle from the move. Not doing so can affect the performance or lifespan of the dehumidifier.

NOTE: To continuously improve its products, ANDTE reserves the right to modify this information without prior notification. For any questions during assembly, please check the instructions on the product page for reference. Or contact our customer service with any questions, comments, or concerns. We are online 24H for you. Thank you for using ANDTE products in your home!

Made in China

Important Safety Instructions

To prevent injury and property damage, the following instructions must be followed when using the dehumidifier.

Warning

• Do not place the dehumidifier near a heater. Do not use the dehumidifier near flammable gas or combustibles, such as gasoline, benzene, thinner, etc.
• The dehumidifier shall be installed in accordance with national wiring regulations.
• Always plug into a grounded outlet properly.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified Persons in order to avoid a hazard.
• Do not use the socket if it is loose or damaged.
• Do not modify power cord length or share the outlet with other dehumidifiers.
• Never try to take apart or repair the dehumidifier by yourself.
• Do not place a heavy object on the power cord and make sure that the cord is not compressed.
• Do not place flower vases or other water containers on top of the dehumidifier.
• Do not operate or turn off the dehumidifier by plugging in or unplugging the dehumidifier. Use the control panel instead.
• Disconnect the power if strange sounds, odors, or smoke come from the dehumidifier.
• Do not operate the dehumidifier with wet hands.
• Make sure to turn off and unplug the dehumidifier before cleaning.
• Do not clean the dehumidifier with water. If water enters the dehumidifier, turn off the dehumidifier immediately.
• Care should be taken when using the dehumidifier in a room: infants, children, and the elderly.

Caution

• Hold the plug by the head when taking it out.
• Turn off and disconnect the power when not using the dehumidifier for a long time.
• Install the dehumidifier properly on a floor, table, or shelf that is level and strong enough to support it when the water bucket is full.
• Close all doors, windows and other outside openings to the room.
• Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent.
• Be sure to replace the bucket properly after emptying to prevent water from dripping on the floor.
• Do not climb on or sit on the dehumidifier.
• Never insert your finger or other foreign objects into grills or openings. Take special care to warn children of these dangers.

Parts Identification

Dehumidifier Exterior:

• Control Panel: Located on the top of the unit.
• Outlet: Air outlet grille on the top.

Dehumidifier Front/Side View:

• Handle: For carrying the unit.
• Filter: Located behind the air intake grill.
• Air inlet (with filter): Intake grille on the side/front.
• Humidity sensor: Measures room humidity.
• Water tank: Collects condensed water.
• Drain Hose Outlet: Port for attaching a drain hose.

NOTE: Do not cover or block the air inlet or outlet.

Operation Instructions

1. Position Your Dehumidifier Properly

• Place the dehumidifier on a smooth, level floor that is strong enough to support the dehumidifier with a full bucket of water.
• To maintain efficiency, operate the dehumidifier in an enclosed area. Keep nearby doors and windows closed.
• Maintain a minimum clearance of 20 cm (7.9 inches) on the sides and back of the dehumidifier and 40 cm (15.75 inches) on the top of the dehumidifier to allow for proper air circulation.
• The functioning temperature range is between 5°C (41°F) and 35°C (95°F).
• Any time the dehumidifier is placed on its back or side, it must be allowed to stand upright for 24 hours before plugging in to avoid damage to internal components.

2. Understand the Control Panel

The control panel features the following indicators and buttons:

• SPEED: Controls fan speed (Low/High).
• TIMER: Sets the timer function for auto-on or auto-off.
• LCD Screen: Displays room humidity percentage, set humidity, timer settings, or error codes.
• SETTING: Adjusts the desired humidity level (30%-80% in 5% increments).
• POWER: Turns the dehumidifier on or off.

Power Button and Indicator: Press the POWER button once to turn on/off the dehumidifier. When the dehumidifier has been turned off, the LCD screen turns blank. The indicator above the POWER button will flash when the compressor has not kicked on and will turn to solid green when the compressor kicks on.

Note: When the POWER button indicator flashes, it typically means:

• The set humidity is not 3% lower than the room humidity.
• The dehumidifier has dropped the room humidity level down to the set-point.
• The dehumidifier is under the 3-minute delay protection state.

3. General Operation

Note: This dehumidifier may have been tilted or placed upside down during shipping. To ensure this dehumidifier works properly, please ensure this dehumidifier is upright for at least 24 hours before initial use.

1. Plug In: Plug the power cord into a properly grounded 110-120 volt AC outlet. The control panel will light up briefly. Press the POWER Button to turn the dehumidifier on. If the "FULL" indicator is on, remove and re-install the water bucket properly.
2. Start Up: Press the POWER button to turn the dehumidifier on. It will run with the default setting of 30% set humidity at low fan speed. The LCD screen displays the room humidity reading.
3. Set Humidity: Press the SETTING button repeatedly to choose a desired humidity level between 30%-80% in 5% increments. Wait for 5 seconds for the setting to stabilize.
   • It is recommended to set the humidity at least 10% lower than the room humidity level.
   • If the set humidity level is 30%, the dehumidifier will run continuously in CONTINUOUS Mode.
   • If the target humidity level is set between 35-80%, the dehumidifier will run in Humidstat Mode, automatically stopping or restarting to maintain the room humidity within ±3% of the set-point.
   • The dehumidifier will automatically stop when the water bucket is full or when the room humidity reaches the set-point.
4. Set Fan Speed: Press the FAN button to change the fan speed between HIGH and LOW. The indicator light will show the selected setting. Higher fan speed removes moisture quicker.
5. Shut Down: Press the POWER button again to shut down the dehumidifier.

Timer Setting

The TIMER function allows you to set a delay AUTO-ON or delay AUTO-OFF for the dehumidifier, from 1 hour to 24 hours.

• Setting an AUTO-ON timer: When the dehumidifier is off, selecting Timer will turn the dehumidifier on at the set time.
• Setting an AUTO-OFF timer: When the dehumidifier is running, selecting Timer will turn the dehumidifier off at the set time.

To set the TIMER:

1. Press the TIMER button once; the TIMER indicator will illuminate and the LCD will flash "00".
2. Press the TIMER button repeatedly to change the delay timer in 1-hour increments, up to 24 hours.
3. Wait for 5 seconds after selecting the target timer value for the setting to register automatically.
4. After TIMER setting, the control will count down the remaining time until AUTO-ON or AUTO-OFF.
5. After the timer function is enabled, press the TIMER button again to check the time remaining.

Notes:

• Before setting an AUTO ON timer, turn on the dehumidifier and set a target humidity level first.
• You can only set an AUTO ON timer when the dehumidifier is off, or an AUTO OFF timer when it is on. You cannot set both at the same time.
• The TIMER function operates only once, not indefinitely.
• Ensure power is supplied to the dehumidifier before setting the TIMER.
• Setting the timer to "00" will deactivate the timer function.
• Manually turning the dehumidifier ON/OFF will cancel any pre-set AUTO ON/OFF timer.

Smart Functions

Auto Shut Off

When the water bucket is full and/or the humidity setting is reached, the dehumidifier will shut off automatically.

• When the water bucket is full, the FULL indicator will illuminate, and the dehumidifier will beep for a few seconds.
• When the room humidity drops to the set-point, the power button indicator and the humidity reading on the LCD will flash.

3-Minute Delay Protection Mechanism

To prevent damage, the dehumidifier will not start operation immediately after a cycle ends or interruption. It waits 3 minutes before restarting the compressor. During this time, only the fan runs, and the power button indicator flickers until the compressor starts.

Auto Defrost

When frost builds up on the evaporator coils, the compressor cycles off, and the fan continues to run until the frost disappears. The dehumidifier will then restart automatically.

Auto-Restart

If the dehumidifier shuts off unexpectedly due to a power cut, it will restart with the previous function settings (humidity and fan speed) once power is restored.

Removing Collected Water

1) Emptying the Water Bucket

When the bucket is full, the dehumidifier shuts down, beeps for 5 seconds, and the FULL indicator illuminates. Do not move the dehumidifier at this time to avoid spilling water.

To remove and empty the collected water:

1. Gently remove the bucket by gripping both sides and pulling outward.
2. Pour the condensate out from the side without the float to prevent it from being flushed away.
3. Replace the water bucket in the dehumidifier. The dehumidifier will not function without the bucket installed.

2) Continuous Draining

Water can be automatically emptied into a floor drain by attaching the included drain hose. (You can use any other hoses with an inner diameter of 5/8 inches.)

To Achieve Continuous Drain by Gravity:

1. Remove the water bucket.
2. Find the drain port on the back of the dehumidifier.
3. Attach one end of the drain hose securely to the drain port.
4. Replace the water bucket in the dehumidifier properly.
5. Direct the other end of the hose down to a suitable drainage facility, like a floor drain. The drainage facility should be lower than the drain outlet of the dehumidifier.

Notes:

• Ensure the connection is tight and there are no leaks.
• Ensure the water hose slopes downward to allow water to flow out smoothly, without kinks or bends.
• If draining to an external container, do not submerge the other end of the hose into the drained water.
• To improve gravity draining, raise the dehumidifier onto a higher, flat surface like a table.
• It is recommended to use a short hose. Long hoses may prevent complete draining, leading to stagnant water and mildew.
• When the continuous drain feature is not being used, remove the drain hose from the outlet.

Diagrams showing bucket removal, pouring water, and re-installation are described above. Diagrams showing hose placement: Two incorrect (❌) with kinks or water submersion, one correct (✔️) with a downward slope.

Care & Cleaning

To avoid electric shock, turn off and disconnect the dehumidifier from the power source before cleaning or maintenance.

1. Clean the Vent and Case

• Use water and a mild detergent. Do not use bleach or abrasives.
• Do not splash water directly onto the dehumidifier, as this may cause electric shock, damage insulation, or cause rust.
• The air intake and outlet vents get soiled easily; use a vacuum attachment or brush to clean them.

2. Clean the Reservoir

• Every few weeks, clean the reservoir to prevent mold, mildew, and bacteria growth.
• Partially fill the reservoir with clean water and a little mild detergent. Swish it around, empty, and rinse.

NOTE: Do not clean the reservoir in a dishwasher.

3. Clean the Air Filter

The air filter should be cleaned approximately every 2 weeks. More frequent cleaning may be needed if there is significant dander or fur in the air.

Follow the steps below to clean the filter:

• The air filter is located behind the rear intake grill. Remove the intake grill and take out the filter.
• Use a vacuum cleaner with a soft brush attachment to remove large debris or dust build-up.
• Wash the filter in lukewarm, soapy water (below 40°C/104°F) or use a neutral cleaning agent.
• Rinse the filter with clean water and dry thoroughly.
• Re-install the filter.

NOTE: DO NOT operate the dehumidifier without a filter, as dirt and lint will clog it, reducing performance.

Store the Dehumidifier

When not using the dehumidifier for a long period, follow these steps for cleaning and proper storage:

• Operate the dehumidifier on high fan mode for half a day, then wait 1 day before emptying the reservoir.
• Clean the dehumidifier housing, water reservoir, and air filter. Ensure the entire dehumidifier is clean and dry.
• Take out the water bucket, place the plug and cord inside the bucket, and then replace the bucket in the dehumidifier.
• Cover the dehumidifier with a plastic bag.
• Store the dehumidifier upright in a dry, well-ventilated place.

Troubleshooting

Safety Precautions

(Note: The following points are described with accompanying illustrations in the original document.)

• 1. Avoid Vibration/Movement: Do not place the dehumidifier on uneven ground to avoid vibration or movement.
• 2. Avoid Obstructions: Do not use thin rods or hard objects to insert into the fuselage to avoid malfunction or danger.
• 3. Keep Away from Heat: When using, keep the dehumidifier away from heat sources such as heaters and electric kettles to save electricity.
• 4. Close Openings: When using, please close the doors and windows to achieve the best dehumidification effect.
• 5. Ensure Ventilation: Do not place items before and after the dehumidifier. If the ventilation is blocked, the dehumidification effect will be affected.
• 6. Unplug When Not in Use: In case of power failure or long-term non-use, please unplug the power cord.
• 7. Cleaning Method: When cleaning the dehumidifier, gently wipe it with a damp cloth; do not directly spray water to clean it.
• 8. Avoid Placing Objects on Top: Do not place any objects on the dehumidifier.
• 9. Filter Cleaning Frequency: Please clean the filter every two weeks (do not use hot water above 104°F/40°C, alcohol, gasoline, or toluene).
• 10. Drainage Pipe Placement: During continuous drainage, the drainage pipe must be placed horizontally or downwards, and must not be uneven or entangled.
• 11. Filter Drying: After the filter is cleaned, please do not place it in direct sunlight to dry it to avoid deformation.
• 12. Prepare for Moving: Before moving or carrying the dehumidifier, please pour out the accumulated water in the water tank.

Service

ANDTE offers a limited 1-year free warranty on this PD161A dehumidifier, with original proof of purchase (order number or other information to prove a genuine purchase). The warranty covers defects arising from faulty manufacture, parts, or workmanship during the warranty period.

During the warranty period, for damaged parts, ANDTE will provide a replacement part if it can restore normal use. The warranty does not apply where damage is caused by factors including, without limitation:

• Normal wear and tear.
• Abuse, mishandling, accident, or failure to follow operating instructions.
• Exposure to liquid or infiltration of foreign particles.
• Servicing or modifications of the product other than by ANDTE.

ANDTE will inspect the dehumidifier through photos or videos to troubleshoot and solve problems. These are general terms for warranty service; customers are urged to reach out with any issue, regardless of warranty terms.

For more warranty information, please contact us at AndteServices@outlook.com.

Warranty and Service

If you have an issue with an ANDTE product, please contact us at AndteServices@outlook.com, and we will do our best to resolve it for you.

Support Hours

24 Hours available.

*Please have your order number ready before contacting customer support.

(Note: The document mentions a "Product Certification" and "OQC" stamp, indicating quality inspection.)