Important Information
IMPORTANT: RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
This manual contains important information regarding the assembly and use of your HOMCOM product. Please read it thoroughly before beginning assembly and keep it for future reference.
General Assembly Notes & Warnings
Quickfit Installation: Tighten the quickfit until its shoulder is flush with the panel. Do not overtighten or undertighten.
Cam Lock Installation: When fitting the cam lock, ensure the starting position is correct before you insert the connecting quickfit. The quickfit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the quickfit.
Cam Lock Tightening: Turn the cam lock clockwise to tighten.
Drawer Slide Alignment: Please find the exact hole for installation, otherwise, it will be misaligned. The screws on the drawer slide must be leveled; otherwise, it will affect the smoothness of the drawer. Be careful to push in the board when both sides of the slide way have been aligned.
Hinge Adjustment: It may be necessary to adjust the hinges so that the doors align. Use the instructions below as a guide.
- Vertical Adjustment: To adjust the door vertically, loosen the screw as shown ? and move the door up and down as needed.
- Gap Adjustment: To adjust the gap between the door and the main frame, turn the screw clockwise ↩️ or anti-clockwise ↪️ as needed.
- Lateral Adjustment: To adjust the door laterally, adjust the screw as shown by turning clockwise ↩️ or anti-clockwise ↪️.
Wall Mounting: This is an anti-dumping belt that fixes the product to the wall and can be used or not, following your needs. If it is a solid wall, please use expansion and self-tapping screws. If it is a wooden wall, only use self-tapping screws. Please do not overtighten the screws.
Parts List
| Part Number | Description | Quantity |
|---|---|---|
| 1 | Top Panel | x1 |
| 2 | Left Side Panel | x1 |
| 3 | Right Side Panel | x1 |
| 4 | Bottom Panel | x1 |
| 5 | Drawer Front Panel | x1 |
| 6 | Shelf Panel | x2 |
| 7 | Drawer Slide Rail (Left) | x1 |
| 8 | Drawer Slide Rail (Right) | x1 |
| 9 | Drawer Back Panel | x1 |
| 10 | Drawer Side Panel | x2 |
| 11 | Middle Divider Panel | x1 |
| 12 | Back Support Panel | x1 |
| 13 | Leg | x1 |
| 14 | Door Panel | x3 |
| 15 | Door Panel | x1 |
| 16 | Drawer Bottom Panel | x1 |
| 17 | Drawer Bottom Panel | x1 |
| 18 | Drawer Side Panel | x2 |
| 19 | Drawer Front Support | x2 |
| 20 | Drawer Back Support | x2 |
| 21 | Drawer Bottom Panel | x2 |
| 22 | Drawer Slide Rail | x2 |
Hardware List
| Code | Description | Quantity | Dimensions |
|---|---|---|---|
| A | Cam Bolt | x30 (+1 spare) | Ø6x35mm |
| B | Cam Lock | x30 (+1 spare) | Ø15x10mm |
| C | Screw | x26 (+1 spare) | Ø6x30mm |
| D | Screw | x18 (+1 spare) | Ø4x35mm |
| E | Screw | x32 (+1 spare) | Ø3.5x12 mm |
| F | Buckle | x8 | N/A |
| G | Screw | x8 (+1 spare) | Ø4x18mm |
| H | Screw | x8 | N/A |
| I | Screw | x8 (+1 spare) | Ø3x16mm |
| J | Bracket | x2 | N/A |
| K | Screw | x2 | Ø4x14mm |
| L | Drawer Slide Rail | x2 | N/A |
| M | Screw | x4 | N/A |
| N | Ring Pull Handle | x4 | N/A |
| O | Bracket | x2 | N/A |
| P | Hinge | x48 (+1 spare) | Ø3.5x14 mm |
| Q | Hinge Plate | x4 | N/A |
| R | Knob | x1 | N/A |
| S | Hinge Plate | x4 | N/A |
| CL | Drawer Slide Rail (Left) | x2 | L300mm |
| CR | Drawer Slide Rail (Right) | x2 | L300mm |
| DL | Drawer Slide Rail (Left) | x2 | L300mm |
| DR | Drawer Slide Rail (Right) | x2 | L300mm |
Assembly Steps
Step 01: Attaching Drawer Slides to Panel 5
Attach drawer slide rails CL and CR to panel 5 using screws E. Ensure the rails are oriented correctly.
Diagram shows panel 5 with two drawer slide rails (CL, CR) being attached using screws E.
Step 02: Attaching Cam Bolts to Panels 7 and 8
Insert cam bolts A into panels 7 and 8. Ensure they are screwed in fully.
Diagram shows panels 7 and 8 with cam bolts A being inserted.
Step 03: Connecting Panels 5, 7, and 8
Connect panels 7 and 8 to panel 5 using cam locks B and screws C. Ensure the cam bolts align with the cam locks.
Diagram shows panels 7 and 8 being attached to panel 5, with cam locks B and screws C used for connection.
Step 04: Connecting Panels 5, 7, 8, and 11
Connect panels 7 and 8 to panel 11 using cam locks B and screws C. Also, connect panel 5 to panel 11 using cam locks B and screws C.
Diagram shows panels 7, 8, and 5 being attached to panel 11 using cam locks B and screws C.
Step 05: Connecting Panels 7, 8, 9, and 11
Connect panel 9 to panels 7 and 8 using screws D. Connect panel 9 to panel 11 using screws D.
Diagram shows panel 9 being attached to panels 7, 8, and 11 using screws D.
Step 06: Attaching Panel 12 and Brackets
Attach panel 12 to panels 4 and 11 using screws E and brackets O. Ensure correct alignment.
Diagram shows panel 12 being attached to panels 4 and 11 with screws E and brackets O.
Step 07: Attaching Panel 4 and Connecting to Side Panels
Attach panel 4 to panels 7, 8, and 11 using screws C and D. This forms the base structure.
Diagram shows panel 4 being attached to the assembly using screws C and D.
Step 08: Attaching Drawer Slide Rails to Side Panels 2 and 3
Attach drawer slide rails CL and CR to side panels 2 and 3 using screws E.
Diagram shows side panels 2 and 3 with drawer slide rails CL and CR being attached using screws E.
Step 09: Attaching Cam Bolts to Side Panels 2 and 3
Insert cam bolts A into side panels 2 and 3. Ensure they are screwed in fully.
Diagram shows side panels 2 and 3 with cam bolts A being inserted.
Step 10: Connecting Main Frame Structure
Connect panels 3 and 4 to panels 7, 8, and 11 using cam locks B and screws C. This step continues building the main cabinet frame.
Diagram shows the main cabinet frame being assembled using panels 3, 4, 7, 8, 11, cam locks B, and screws C.
Step 11: Inserting Middle Divider and Shelf
Insert middle divider panel 6 into the assembled frame. Insert shelf panel 6 into the designated slots.
Diagram shows the middle divider panel 6 and a shelf panel 6 being inserted into the cabinet structure.
Step 12: Attaching Top Panel and Leg
Attach the top panel 2 to the main structure using cam locks B and screws C. Attach the leg 13 to the bottom panel 4 using knob R.
Diagram shows the top panel 2 being attached and the leg 13 being attached to the bottom with knob R.
Step 13: Inserting Drawer Assembly
Slide the assembled drawer structure into the cabinet. The back panel 6 is shown being inserted into grooves.
Diagram shows the main cabinet structure with the back panel 6 being slid into place, and the drawer assembly (parts 5, 7, 8, 9, 11) being inserted.
Step 14: Attaching Top Panel and Side Panels
Attach the top panel 1 to the side panels 2 and 3 using cam bolts A and screws C. Rotate the assembly 180 degrees.
Diagram shows top panel 1 being attached to side panels 2 and 3 with cam bolts A and screws C, followed by a 180-degree rotation.
Step 15: Attaching Drawer Slides and Buckles
Attach drawer slide components F to the cabinet frame. The buckles F have 3 optional adjustment positions.
Diagram shows buckles F being attached to the cabinet interior using screws.
Step 16: Assembling and Attaching Hinges and Plates to Doors
Attach hinges P and hinge plates Q/S to door panels 14 and 15 using screws G and M. Use screws P for hinges and screws G for plates.
Diagram shows hinges P and plates Q/S being attached to door panels 14 and 15 using screws G and M.
Step 17: Attaching Doors to Cabinet
Attach the assembled doors (panels 14, 15) to the cabinet using the pre-attached hinges and plates. The diagram shows various hinge adjustment options (I-V).
Diagram shows doors 14 and 15 being attached to the cabinet. It also illustrates hinge adjustment steps I through V.
Step 18: Assembling Drawer Boxes
Assemble the drawer boxes using panels 16, 17, 18, 19, 20, 21, and 22. Attach cam bolts A to panels 16 and 17, and connect them to panels 18, 19, 20, 21, 22 using screws D.
Diagram shows the assembly of drawer boxes using various panels and hardware, including cam bolts A and screws D.
Step 19: Attaching Drawer Slides to Drawer Boxes
Attach drawer slide rails DL and DR to the assembled drawer boxes using screws E and B. Ensure correct orientation.
Diagram shows drawer slide rails DL and DR being attached to the drawer boxes using screws E and B.
Step 20: Attaching Drawer Runners to Cabinet
Attach drawer runners (parts H, I, J, K) to the inside of the cabinet frame. Use screws H, I, and K. Brackets J are also used.
Diagram shows drawer runners being attached to the cabinet interior using screws H, I, K, and brackets J.
Step 21: Inserting Drawers and Handles
Slide the assembled drawers into the cabinet. Attach ring pull handles N to the drawer fronts using screws G.
Diagram shows drawers being inserted into the cabinet and ring pull handles N being attached to the drawer fronts with screws G.
Step 22: Wall Anchoring (Anti-Tip Belt)
Secure the furniture to the wall using the anti-tip belt and screws D. Locate a suitable point on the wall and attach the bracket. Ensure the belt is taut.
Diagram shows the furniture being anchored to a wall using screws D and a bracket, with the anti-tip belt.
Contact Information & Recycling
For any questions or assistance, please refer to the contact details provided for your region on the back page of the manual. Please also consider recycling this product responsibly.
Recycling: DONNEZ OU RECYCLEZ (Give or Recycle) - ASSOCIATION, LIVRAISON, DÉCHÈTERIE (Association, Delivery, Waste Disposal Centre).
