STEP 1
Attach the Headboard (1) to the Headboard Support Leg (7) using screws C (4 PCS) and the Allen Key (F, 1 PC). Note: Ensure the locking mechanism is set correctly, with locks 2-4 in the low position and locks 1-3 in the high position.
Parts List
| Part Number | Description | Quantity |
|---|---|---|
| 1 | Headboard | 1 PC |
| 2 | Side Rail (Left) | 1 PC |
| 3 | Headboard Support Leg | 1 PC |
| 4 | Slat Support Rail | 1 PC |
| 5 | Center Support Leg (High) | 2 PCS |
| 6 | Side Rail (Right) | 1 PC |
| 7 | Headboard Support Leg | 1 PC |
| 8 | Wooden Slats | 2 PCS |
| 9 | Center Support Rail | 2 PCS |
| 10 | Center Support Leg | 1 PC |
| 11 | Center Support Leg | 1 PC |
| 12 | Footboard Rail | 2 PCS |
| 13 | Support Bracket | 4 PCS |
| 15 | Footboard Support Leg (Short) | 2 PCS |
| 16 | Side Rail | 1 PC |
| 17 | Headboard Support Rail | 1 PC |
| 18 | Headboard Support Rail | 1 PC |
| 19 | Mounting Bracket | 4 PCS |
| 20 | Mounting Bracket | 2 PCS |
| 22 | Light bar | 2 PCS |
| 23 | Remote control | 1 PC |
| 24 | Power cord | 1 PC |
| A | M8x20mm Screw | 40+2 PCS |
| B | M8x35mm Screw | 12+1 PCS |
| C | M8x40mm Screw | 4 PCS |
| D | M8x60mm Screw | 1 PC |
| E | M4x25mm Screw | 8+1 PCS |
| F | M8 Allen Key | 1 PC |
| G | Adjustment Tool | 1 PC |
| H | Ø8x22mm Washer | 5+1 PCS |
Assembly Instructions
STEP 2
Attach the Headboard (1) to the Side Rail (Left) (2) and Side Rail (Right) (6) using screws A (4 PCS) and the Allen Key (F, 1 PC).
STEP 3
Attach Slat Support Rails (4) and Mounting Brackets (19) to the side rails using screws A (6 PCS) and the Allen Key (F, 1 PC). Do not tighten screws completely yet (approx. 75% tight).
STEP 4
Attach Headboard Support Rails (18) and Mounting Brackets (20) to the side rails using screws A (6 PCS) and the Allen Key (F, 1 PC). Do not tighten screws completely yet (approx. 75% tight).
STEP 5
Attach Side Rails (16) to the Slat Support Rails (4) and Headboard Support Rails (18) using screws A (4 PCS) and the Allen Key (F, 1 PC). Once all holes are aligned, tighten all screws fully (100%).
STEP 6
Attach Center Support Legs (10) to the Side Rails (16) using screws A (4 PCS) and the Allen Key (F, 1 PC).
STEP 7
Attach Center Support Legs (5) to the Center Support Legs (10) and Side Rails (16) using screws B (4 PCS) and the Allen Key (F, 1 PC). Ensure correct orientation for "High" and "Short" legs as shown.
STEP 8
Attach Footboard Support Legs (Short) (15) to the Footboard Rails (12) using screws B (4 PCS) and the Allen Key (F, 1 PC). Repeat for both sides (x2). Ensure correct orientation for "High" and "Short" legs as shown.
STEP 9
Attach Side Rails (16) to the Footboard Rails (12) using screws A (8 PCS) and the Allen Key (F, 1 PC).
STEP 10
Assemble the center support structure. Attach Center Support Rails (9) to Center Support Legs (11) and Support Brackets (13) using screws B (4 PCS), H (4 PCS - washers), and the Allen Key (F, 1 PC).
STEP 11
Connect the assembled center support structure to the frame. Attach Center Support Rails (9) to Center Support Legs (10) and (11) using screws D (1 PC), H (1 PC - washer), and the Allen Key (F, 1 PC).
STEP 12
Attach Side Rails (16) to the Center Support Rails (9) using screws A (2 PCS) and the Allen Key (F, 1 PC).
STEP 13
Final tightening. Secure all remaining screws, ensuring all parts are aligned. Tighten all screws fully (100%).
STEP 14
Install LED Light Strip (22). Pull out and unfold the LED light strip. Attach the luminous surface side with Velcro A to the corresponding Velcro B on the bed frame. Start from the middle of the bed end. Connect the Power Cord (24) to the USB socket. The USB socket must be connected to a power source to use the light. Secure excess wiring by packing it up and tying it neatly.
STEP 15
Place the Wooden Slats (8) onto the bed frame supports.
STEP 16
Attach the adjustable feet (E) to the bottom of the frame using the Adjustment Tool (G, 1 PC). These feet can be turned to adjust the bed's level on uneven floors.
STEP 17
Remote Control Operation: Use the remote control (23) to operate the LED light. The LED lamp functions only after the power supply is connected. For app control, scan the QR code on the manual/controller to install the application. Ensure your phone's Bluetooth is enabled. The LED light will automatically connect to the app.
Thanks Gracias!
