Important Information
Seller and Manufacturer Disclaimer
[!] Seller and Manufacturer disclaim all and any liability for property damage, personal injury, or loss, direct, indirect, or incidental, resulting from the incorrect assembly, inadequate maintenance, improper use, or neglect of this product.
Notice
[!] Keep these assembly instructions for future reference. Do not use this product if there are missing, damaged, or broken parts until repairs are made and/or factory replacement parts are installed. Check all packing material carefully for small hardware that may have become loose inside the carton during shipment. Identify and count all hardware and parts to compare with parts and hardware list. Follow assembly instructions closely. Improper assembly can result in personal or property damage. Secure all bolts before use. Every 90 days check all bolts are secured. Some parts may have a sharp corner or edge and maybe heavy. Do not use or store this product near open flames or around flammable chemicals.
[!] When placing contents on non-carpeted flooring, it's recommended to use floor protection such as an area rug or furniture pads. These are not included with the purchase.
[!] Do not drag or push the bed frame. To ensure safe moving, always use two people to lift and re-position the bedframe. Avoid dragging or pushing it across the floor to prevent damage to the legs, slats, and the center support legs.
Replacement Part or Hardware Request
Request a replacement by logging into the marketplace account in which the purchase was made and sending a message to the seller. To assist in expediting the request attach applicable images relevant to the request and/or part number and quantity.
Additional Tool Required
#2 Philips Screwdriver (Not Provided)
Bed Parts
- A Headboard
- B Headboard Wing Left
- C Headboard Wing Right
- D Footboard
- E Bottom Wood Base
- F Side Rail Left
- G Side Rail Right
- H Side Rail Wood Bottom
- I Center Rail
- J Center Support Leg
- K Bed Slat
Hardware
- L Bolt M6 x 15mm
- M Bolt M6 x 35mm
- N Bolt M6 x 45mm
- O Bolt M6 x 80mm
- P Bolt M8 x 20mm
- Q Bolt M8 x 70mm
- R Flat Washer M6
- S Spring Washer M6
- T Bed Washer M6
- U L-Bracket
- V Barrel Nut M8
- W Adjustable Feet
- X Screw M4 x 25mm
- Y Ball End Hex Key Wrench
- Z Hex Key Wrench M5
Bed Assembly Steps
Step 1: Attach Bottom Wood Base to Headboard and Footboard
Parts Used: Headboard (A) ×1, Footboard (D) ×1, Bottom Wood Base (E) ×2
Hardware Used: Bolt (O) M6 x 80mm ×6, Flat Washer (R) M6 ×6, Ball End Hex Key Wrench (Y) ×1
Attach the Bottom Wood Base (E) to the Headboard (A) and Footboard (D) using Bolts (O) and Flat Washers (R). Use the Ball End Hex Key Wrench (Y) for tightening. Note: Do not fully tighten bolts at this stage to allow for adjustments.
Step 2: Attach Side Rail Wood Bottom to Side Rails
Parts Used: Side Rail Left (F) ×1, Side Rail Right (G) ×1, Side Rail Wood Bottom (H) ×2
Hardware Used: Bolt (O) M6 x 80mm ×6, Flat Washer (R) M6 ×6, Ball End Hex Key Wrench (Y) ×1
Attach the Side Rail Wood Bottoms (H) to the Side Rails (F and G) using Bolts (O) and Flat Washers (R). Use the Ball End Hex Key Wrench (Y). Note: Do not fully tighten bolts at this stage.
Step 3: Attach Headboard Wings to Headboard
Parts Used: Headboard Wing Left (B) ×1, Headboard Wing Right (C) ×1, Headboard (A) ×1
Hardware Used: Bolt (M) M6 x 35mm ×6, Flat Washer (R) M6 ×6, Ball End Hex Key Wrench (Y) ×1
Attach the Headboard Wings (B and C) to the Headboard (A) using Bolts (M) and Flat Washers (R). Use the Ball End Hex Key Wrench (Y).
Step 4: Connect Headboard and Footboard Assembly to Side Rails
Parts Used: Assembled Headboard/Footboard section, Side Rails (F, G) ×2, Footboard (D) ×1
Hardware Used: Bolt (P) M8 x 20mm ×4, Hex Key Wrench (Z) ×1, Bolt (N) M6 x 45mm ×2, Spring Washer (S) M6 ×2, Bed Washer (T) M6 ×2, Ball End Hex Key Wrench (Y) ×1
Attach the Footboard (D) to the Side Rails (F and G) using Bolts (P) and the Hex Key Wrench (Z). Attach the Assembled Headboard section to the Side Rails (F and G) using Bolts (N), Spring Washers (S), and Bed Washers (T) with the Ball End Hex Key Wrench (Y). Note: Do not tighten bolts at this step.
Step 5: Secure Assembled Bed Frame
Hardware Used: Bolt (N) M6 x 45mm ×6, Flat Washer (R) M6 ×4, Spring Washer (S) M6 ×2, Bed Washer (T) M6 ×2, Ball End Hex Key Wrench (Y) ×1
Affix Bolts (N), Flat Washers (R), Spring Washers (S), and Bed Washers (T) to the assembled bed structure using the Ball End Hex Key Wrench (Y) as shown in the diagram. Note: Do not tighten bolts at this step.
Step 6: Final Tightening of Frame Bolts
Hardware Used: Bolt (O) M6 x 80mm ×2, Flat Washer (R) M6 ×2, Spring Washer (S) M6 ×2, Bed Washer (T) M6 ×2, Ball End Hex Key Wrench (Y) ×1
Affix Bolts (O) and Washers (R, S, T) to the assembled bed structure using the Ball End Hex Key Wrench (Y). Note: Tighten all bolts after all bolts are in place.
Step 7: Attach Adjustable Feet to Center Support Legs
Parts Used: Center Support Leg (J) ×4
Hardware Used: Adjustable Feet (W) ×4
Attach the Adjustable Feet (W) to the bottom of each Center Support Leg (J) as shown.
Step 8: Attach L-Bracket to Center Rail
Parts Used: Center Rail (I) ×1
Hardware Used: Bolt (L) M6 x 15mm ×2, L-Bracket (U) ×2, Ball End Hex Key Wrench (Y) ×1
Attach the L-Brackets (U) to the Center Rail (I) using Bolts (L) and the Ball End Hex Key Wrench (Y). This is shown from the bottom view of the center rail.
Step 9: Attach Center Rail Assembly to Bed Frame
Parts Used: Assembled Center Rail (I)
Hardware Used: Bolt (L) M6 x 15mm ×2, Ball End Hex Key Wrench (Y) ×1
Attach the assembled Center Rail (I) to the main bed frame (connecting to Headboard A and Footboard D) using Bolts (L) and the Ball End Hex Key Wrench (Y) as shown.
Step 10: Attach Bed Slats to Center Rail
Parts Used: Bed Slat (K) ×13
Hardware Used: Bolt (Q) M8 x 70mm ×4, Barrel Nut (V) M8 ×4, Hex Key Wrench (Z) ×1
Attach the Bed Slats (K) to the Center Rail (I) using Bolts (Q) and Barrel Nuts (V). Use the Hex Key Wrench (Z) for tightening.
Step 11: Secure Bed Slats to Frame
Hardware Used: Screw (X) M4 x 25mm ×26
Tools Required: [Philips Screwdriver] (Not Provided)
Affix the Bed Slats (K) to the bed frame using Screws (X) and a Philips Screwdriver as shown in the diagram. Ensure each slat is securely fastened.
Step 12: Final Adjustments and Placement
Hardware Used: Adjustable Feet (W)
WARNING! Ensure the adjustable feet (W) are perpendicular to the floor before using the bed. Rotate them clockwise or counterclockwise until firmly against the floor for stability. Note: The adjustable feet rotate to fit the floor; one may need clockwise rotation while the other counterclockwise, depending on leveling and assembly.
Important Note: Do not drag or push the bed frame. To ensure safe moving, always use two people to lift and re-position the bed frame. Avoid dragging or pushing it across the floor to prevent damage to the legs, slats, and center support legs.
