Ecler ePRS10Ti / ePRS20Ti Special Loudspeakers
User Manual
Important Information
Important Note: Congratulations on your purchase of an Ecler product. We thank you for your trust. To ensure maximum efficiency and performance, it is very important to read and follow the instructions in this manual before any connection. For optimal operation, we recommend that any maintenance be carried out by our authorized technical services.
Introduction: The ePRS10Ti and ePRS20Ti are two public address loudspeakers carefully selected for the most common 70/100 V line applications: announcements and background music. They offer great longevity and optimal reproduction of voice and music. Made from reinforced ABS and IP55 certified, they are ideal for high performance outdoors.
Main Features:
- Water-resistant ABS two-way horn loudspeaker
- ePRS10Ti (power settings):
- 10W / 5W / 2.5W @ 100V
- 5W / 2.5W / 1.25W @ 70V
- ePRS20Ti (power settings):
- 20W / 10W / 5W @ 100V
- 10W / 5W / 2.5W @ 70V
- IP55 protection rating
- Bare wire connection
- White finish (RAL 9016)
Connection
6.1. ePRS10Ti:
Power selection for the 70/100 V line is made by wiring the connection according to the following color code:
| Color | @100V | @70V |
|---|---|---|
| WHITE | 10W | 5W |
| GREEN | 5W | 2.5W |
| RED | 2.5W | 1.25W |
| BLACK | COM | COM |
6.2. ePRS20Ti:
Power selection for the 70/100 V line is made by wiring the connection according to the following color code:
| Color | @100V | @70V |
|---|---|---|
| WHITE | 20W | 10W |
| GREEN | 10W | 5W |
| RED | 5W | 2.5W |
| BLACK | COM | COM |
Note: If the loudspeaker is used in 70 V installations, the power ratings will be halved compared to those indicated on the selector for the 100 V position. For 50 V installations, the power will be a quarter.
WARNING! If you accidentally connect the system to a low impedance amplifier with the switch in the 100 V/60 W position, it will not damage the loudspeaker, but it will perform well below its normal performance level. However, if you accidentally connect the loudspeaker to a 70/100 V line while its selector is in the 8 Ω position, it will be seriously damaged.
Placement and Mounting
In general, the following points should be observed:
- Always install the unit on firm and solid surfaces.
- Ensure that the surface on which the loudspeaker is to be installed can support its weight.
- Always use a safety sling to secure the loudspeaker installation.
- For good sound reproduction, there should be no obstacles between the unit and the audience. High frequencies, unlike low frequencies, are extremely directional, and any obstacle will cause an attenuation of their response.
Technical Specifications
ePRS10Ti
| Drivers | 5" |
| Power options @ 100V | 10W / 5W / 2.5W |
| Power options @ 70V | 5W / 2.5W / 1.25W |
| Frequency response (-3dB) | 158 Hz-19 kHz |
| Coverage angle | 235°x235° (HxV) |
| Sensitivity 1W/1m | 90 dB |
| IP rating | IP55 (IEC60529 Certified) |
| Finished color | White (RAL 9016) |
| Material | ABS + Aluminum grill |
| Operating and storage conditions | Min: -20°C ; -4°F Max: 70°C; 158°F |
| Cord length | 350mm / 13.8“ |
| Dimensions (Ø x L) | Ø 138 x 205mm / Ø 5.4" x 8.1” |
| Weight | 1.6 kg. / 3.5 lb. (including accessories) |
ePRS20Ti
| Drivers | 6.5" |
| Power options @ 100V | 20W / 10W / 5W |
| Power options @ 70V | 10W / 5W / 2.5W |
| Frequency response (-10dB) | 170 Hz-19 kHz |
| Coverage angle | 151°x151° (HxV) |
| Sensitivity 1W/1m | 96 dB |
| IP rating | IP55 (IEC60529 Certified) |
| Finished color | White (RAL 9016) |
| Material | ABS + Aluminum grill |
| Operating and storage conditions | Min: -20°C ; -4°F Max: 70°C; 158°F |
| Cord length | 350mm / 13.8“ |
| Dimensions (Ø x L) | Ø 170 x 245mm / Ø 6.7" x 9.6” |
| Weight | 1.8 kg. / 4.0 lb. (including accessories) |
1 6dB below the sound pressure level at specified sensitivity
2 Measured on-axis, far field and referenced to 1 meter by inverse square law. Average from 100 Hz to 10 kHz.
Package Contents
- ePRS10Ti or ePRS20Ti
- User quick start guide
- Warranty card
