Instruction Manual C-6001
Model: C-6001
Contact: HJ-Customer-Service@outlook.com | (909)637-7665 | (909)637-7593 | EST 9:00AM--17:00PM
Care and Maintenance
To deodorize the leather, leave the chair in a shady area outside for 1-2 days.
For longer use, re-tighten bolts every 6 months using the enclosed allen-key. ⚠️ Using an electric drill can damage the chair. Please re-tighten bolts manually.
Safety Information
- ✔️ Sit in the center of the chair, with your back to the backrest.
- ❌ Do not sit at the front edge of the chair.
- ❌ Do not stand on the chair.
- ❌ Do not use the chair with more than one person.
- ❌ Do not push the chair around when a person is sitting in it.
- ❌ Do not push down on the backrest when a person is reclined.
- ❌ Do not place all your weight on only the backrest.
Package List
| Item Code | Description | Quantity |
|---|---|---|
| (A) | Casters | 5 |
| (B) | Base | 1 |
| (C) | Gas Lift | 1 |
| (D) | Mechanism | 1 |
| (E) | Back Plate | 1 |
| (F) | Armrests Cushion | 2 |
| (G) | Armrests | 2 |
| (H) | Backrest | 1 |
| (I) | Seat | 1 |
| (J) | Footrest | 1 |
| (K) | Back Pad | 1 |
| (L) | Bolts M6*20mm | 12 |
| (M) | Bolts M6*25mm | 12 |
| (N) | Bolts M8*20mm | 3 |
| (O) | Clasp | 2 |
| (P) | Gasket | 3 |
| (Q) | Wrench | 1 |
Assembly Instructions
Step 1
Press the Casters (A)*5 into the holes at the end of Base (B).
[Diagram: Base (B) with five holes at the bottom, Casters (A) being inserted into these holes.]
Step 2
Insert the Gas Lift (C)*1 into the Base (B).
[Diagram: Base (B) with Gas Lift (C) inserted vertically into the center hole.]
Step 3
Attach the Armrests Cushion (F)*2 and Armrests (G)*2 to the Seat (I)*1 using Bolts (L)*4 (per side) and Bolts (M)*4 (per side).
Note: Make sure the buttons of the Armrests (G) are on the outside.
[Diagram: Underside of Seat (I) showing attachment points for Armrests (G) and Armrest Cushions (F) using bolts.]
Step 4
Attach the Mechanism (D)*1 to the Seat (I)*1 using Bolts (M)*4.
Note: Make sure the "FRONT" markings of the Mechanism (D) and the Seat (I) are in the same direction.
[Diagram: Underside of Seat (I) showing Mechanism (D) being attached with bolts, with "FRONT" markings indicated.]
Step 5
Attach the Armrests (G)*2 to the Seat (I)*1 using Bolts (L)*8.
[Diagram: Underside of Seat (I) showing Armrests (G) being attached with bolts.]
Step 6
Attach the Backrest (H)*1 to the Back Plate (E)*1 using Bolts (M)*4.
Note: Lift the velcro strips on the back of the Backrest (H) to find the screw holes.
[Diagram: Backrest (H) with velcro strips lifted, showing screw holes for attachment to Back Plate (E).]
Step 7
Insert the Back Plate (E)*1 into the Mechanism (D)*1 using Bolts (N)*3 and Gaskets (P)*3.
[Diagram: Mechanism (D) and Back Plate (E) being joined with bolts (N) and gaskets (P).]
Step 8
Align the hole on Mechanism (D)*1 with the Gas Lift (C)*1, and press the Chair down until it is fully secured.
Your chair is ready for use. The Back Pad (K)*1 can be attached if desired.
[Diagram: Assembled chair being lowered onto the Gas Lift (C) attached to the Base (B).]
Instructions For Use
1. Seat Height
Adjusting handle on the right side.
⬆️ To raise
⬇️ To lower
2. Backrest Tilt
Adjusting handle on the left side.
? To rocking
? To lock tilt
3. Tilt Tension
Knob under the seat.
➕ To increase tension
➖ To decrease tension
CAUTION
- Before using the chair, check to ensure that all bolts are fully tightened.
- Lubricate all parts and tighten all bolts every 6 months or whenever needed.
