L Shaped Computer Desk Instruction Manual

Model: D-L01-49IN

Attention:

Please do not wipe the desk with corrosive liquids.
Please take good care of the parts to avoid children's contact and accidental ingestion.
Please do not place overheated kitchenware and tableware to avoid damaging the desk.

1 Package List

Parts:

A: Leg
B: Leg
C: Leg
D: Crossbar
E: Crossbar
F (x2): Crossbar
G (x2): Bar
H (x2): Bar
I: Board
J: Board
K: Stand
L: Felt Bag

Hardware:

1 (1x10): Screws M6x45mm
2 (2x11): Screws M6x40mm
3 (3x10): Screws M6x12mm
4 (4x2): Screws M6x25mm
5 (5x2): Nut M6
6 (6x2): Wooden Dowel 8x40
7: Wrench M4
8 (8x2): Cover-up Sticker
9: Wrench

Assembly Steps

Step 1

Attach Crossbars (D&E) to the front and middle of the Legs (A&B) with Screws (1)*4.

Diagram Description: Shows two legs (A, B) standing upright, with two crossbars (D, E) connecting them horizontally. Screws are indicated at connection points.

Step 2

Fix the screw hole in the middle of the Bar (H)*2 with Screw (4)*1 and Nut (5)*1. Fix the crossed Bar (H)*2 to the Legs (A&B) with Screws (3)*4. Note: Screw (4) and Nut (5) are only tightened 50%.

Diagram Description: Shows the partially assembled frame from Step 1. Two bars (H) are attached diagonally across the frame using screws and nuts. A 50% tightening indicator is shown.

Step 3

Attach one side of the Crossbar (F)*2 to the Leg (C) and the other side to the RIGHT side of the installed Desk Frame with Screws (1)*4.

Diagram Description: Shows the desk frame from Step 2, with a new leg (C) being attached to the right side using crossbars (F) and screws.

Step 4

Fix the screw hole in the middle of the Bar (G)*2 with Screw (4)*1 and Nut (5)*1. Attach the crossed Bar (G)*2 to the Legs (B&C) with Screws (3)*4. Note: Screw (4) and Nut (5) are only tightened 50%.

Diagram Description: Shows the desk frame with the right side leg attached. Two bars (G) are attached diagonally across the right side frame using screws and nuts. A 50% tightening indicator is shown.

Step 5

Install Board (I) to one side Desk Frame with Screws (2)*7. Note: Screws are only tightened 50%.

Diagram Description: Shows the desk frame with the main desktop board (I) being attached to the left side of the frame using screws. A 50% tightening indicator is shown.

Step 6

Fix Boards (I&J) with Wooden Dowel (6)*2 so that the two match perfectly. Then attach Board (J) to the Desk Frame with Screws (2)*4. Note: Screws are only tightened 50%.

Diagram Description: Shows the desk frame with board (I) attached. A second desktop board (J) is being attached to the right side, connecting to board (I) with wooden dowels (6) and secured with screws (2). A 50% tightening indicator is shown.

Step 7

Attach Felt Bag (L) to the Leg (A) with Screws (3)*2. Attach Stand (K) to one of the three Legs (A&B&C) with Screws (1)*2. Then use Cover-up Sticker (8)*2 to cover the exposed screw holes on the Board.

Diagram Description: Shows the assembled desk. A felt bag (L) is attached to a leg (A) with screws (3). A stand (K) is attached to one of the legs (A, B, or C) with screws (1). Cover-up stickers (8) are shown being applied to screw holes.

Step 8

100% Tighten all screws before using the Desk, including Screws (4)*2, Nuts (5)*2 and Screws (2)*11.

Diagram Description: Shows the fully assembled L-shaped desk. A 100% tightening indicator is shown, signifying the final tightening of all screws.

Step 9

You can choose another installation method, customize the placement as your habit. Attach Crossbar (F)*2 to the Leg (C) and the LEFT side of the Desk Frame with Screws (1)*4.

Diagram Description: Shows an alternative assembly step, attaching a crossbar (F) to leg (C) and the left side of the desk frame.

Step 10

Fix Bar (G)*2 with Screw (4)*1 and Nut (5)*1. Attach the crossed Bar to the Legs (B&C) with Screws (3)*4. Note: Screw (4) and Nut (5) are only tightened 50%.

Diagram Description: Shows the desk frame during an alternative assembly process, attaching bars (G) to legs (B&C) with screws and nuts. A 50% tightening indicator is shown.

Step 11

Install Board (I) to one side Desk Frame with Screws (2)*7. Note: Screws are only tightened 50%.

Diagram Description: Shows the desk frame during an alternative assembly process, with board (I) being attached to one side of the frame. A 50% tightening indicator is shown.

Step 12

Fix Boards (I&J) with Wooden Dowel (6)*2 so that the two match perfectly. Then attach Board (J) to the Desk Frame with Screws (2)*4. Note: Screws are only tightened 50%.

Diagram Description: Shows the desk frame during an alternative assembly process, with boards (I) and (J) being joined by wooden dowels (6) and secured with screws (2). A 50% tightening indicator is shown.

Step 13

Diagram Description: Shows the desk frame during an alternative assembly process, with a felt bag (L) attached to leg (A) and a stand (K) attached to a leg (A, B, or C). Cover-up stickers (8) are shown.

Step 14