Olight Oclip User Manual

Product Specifications

Table 1: Specifications

Table 2: USB-C Charging Cable

Operating Instructions

3.1 Charge

Connect the USB-C cable to the Type-C Charging Port. The indicator light will be red while charging and turn green when charging is complete. Charging time is approximately 1.5 hours.

(Refer to Figure 2 for charging illustration)

3.2 On/Off

A single press of the button turns the light on or off. The currently active mode is memorized when the device is turned off (Strobe and White Light Beacon modes are not memorized).

(Refer to Figure 3 for On/Off operation)

3.3 Lockout / Unlock

To Lock: When the light is off, press and hold the side switch for approximately 2 seconds. The light will briefly enter Moonlight mode and then turn off, signaling lockout mode. A red indicator in the center of the switch will light up briefly.

To Unlock: Press and hold the side switch for over one second until the Moonlight mode activates.

(Refer to Figure 4 for Lockout/Unlock illustration)

3.4 Moonlight Mode

When the flashlight is off, press and hold the button for 1 second or more to activate Moonlight mode. If the last used mode was Moonlight, a simple press of the button will activate it.

(Refer to Figure 5 for Moonlight mode activation)

3.5 Change Brightness Level (White Light Mode Only)

In white light mode, long press the button to change brightness. The output cycles through Low -> Medium -> High -> Low. Release the button to select the desired brightness. (Note: Moonlight mode is not included in this brightness cycle).

(Refer to Figure 6 for brightness adjustment)

3.6 Strobe Mode

To turn Strobe on, quickly press the button three times or more when the light is off. Press or press and hold the button to turn off Strobe mode.

(Refer to Figure 7 for Strobe mode activation)

3.7 Red Light Mode

Double-press the button to activate red light mode, regardless of whether the light is on or off. When the light is turned on again, the current setting is memorized.

(Refer to Figure 8 for Red light mode activation)

3.8 Switch Between Red and White Light Mode

When the device is on, double-press the button to switch between red light mode and white light mode.

(Refer to Figure 9 for mode switching)

3.9 Change Red Light Mode

In red light mode, press and hold the button for more than 0.5 seconds to switch to red light blink. Release the button, then press and hold again for more than 0.5 seconds to return to constant red light.

(Refer to Figure 10 for red light mode changes)

3.10 Turn on White Light Beacon

To activate the White Light Beacon, quickly press the button three times or more when the light is off or in red light mode. Press or press and hold the button to turn off the Beacon.

(Refer to Figure 11 for Beacon activation)

4. Battery Indicator

The battery level is indicated by the color of the indicator light:

• Green: 60-100%
• Orange: 30-60%
• Red: 0-30%

(Refer to Figure 12 for battery indicator illustration)

Safety Warnings

DANGER

• Do not disassemble the product.
• Do not throw the product into fire, as it may cause the battery to burn or explode, leading to unpredictable disasters.

CAUTION

• Do not look directly at the light source or shine it into your eyes, as this may cause temporary blindness or permanent eye damage.
• Do not obstruct the lens, as the energy emitted from the light may cause the object to burn.
• Do not place, charge, or use the light in a car or similar environment where the internal temperature may exceed 60°C.
• Do not immerse the product in water or other liquids, as this will damage the product.
• Do not place the light in a dusty environment, as dust may enter the switch and cause functional failure.
• The magnetic clip may attract metal dust; clean it immediately to ensure proper function.

NOTICE

• Use only the TYPE-C charging cable to charge the product to avoid damage.
• Charge the product completely before storing it for a long period.
• Lock the product if it is carried or transported.
• Keep the dust cover closed when the charging port is not in use to prevent dust and foreign objects from entering.

REMARK

• Do not put a hot light into any type of fabric bag or fusible plastic container.
• This product is not a toy for pets.
• When the ambient temperature is below 0°C/32.0°F, the light can only output at the low and medium brightness modes.

Warranty & Support

Warranty:

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 2 years of purchase: Contact Olight for repair or replacement.
• For low-value fittings (lanyards, clips) with quality problems or damage under normal use within 30 days, contact after-sale service. For issues after 30 days or due to abnormal use, Olight provides conditional quality assurance.

Customer Support:

• USA: cs@olightstore.com
• Global: contact@olightworld.com

Visit www.olightworld.com to see the complete product line.

Manufacturer Information

Dongguan Olight E-Commerce Technology Co., Ltd

4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China

Product Version/Identifier: 3.4000.0635 A. 08,03,2023