Bluestone™ Auto-Clamping Car Mount

Introduction

The Bluestone Auto Clamping Dashboard Mount is designed to be the last car mount you will need. Its sleek black design complements any car interior. It offers versatile positioning with its adjustable arm, allowing you to place and use it in various directions. The suction cup features a strong adhesive base, ensuring a secure and stable attachment to your dashboard or windshield, preventing it from falling or tipping over during your journey.

Package Contents

• 1x Clamp and Release Phone Holder
• 1x Socket
• 1x Back connector
• 1x Suction Cup Stand

Product Overview

The car mount consists of several key components:

• Ball: Connects the mount body to the socket for articulation.
• Extension Knob: Used to tighten or loosen the ball joint for angle adjustment.
• Wings: The adjustable arms that grip the phone.
• Clamp Tighten Button: A button to release the clamp.
• Lever: Located at the bottom of the stand, used to secure the suction cup.
• Bottom Clamp: The base of the mount that attaches to the dashboard or windshield via a suction cup.
• Suction Cup: Provides adhesion to surfaces.

The mount body is approximately 6 cm x 10.5 cm with a depth of 3.5 cm. The adjustable clamp can accommodate devices from 5.5 cm to 8.5 cm wide, with wings that expand up to 10.5 cm.

The stand is typically 14.5 cm tall and can extend up to 19.5 cm. The suction cup has a diameter of 6.5 cm, and the phone holder foot is 1 cm wide.

Specifications & Features

• Strong and secure suction cup to stick to any flat surface.
• Tight fitting clamp with rubber grips for secure phone holding.
• Quick-Use Spring-loaded clamping mechanism.
• Extendable Arm for optimal viewing angle.
• 360° rotating phone bracket for versatile positioning.
• Easy Installation process.
• Sticky suction cup for enhanced grip.
• Adheres to windshield or dashboard surfaces.

Visual Description of Features:

• The mount is shown attached to a car dashboard, demonstrating its primary use case.
• A close-up view highlights the clamp mechanism securely holding a smartphone, showing the rubber grips.
• Another image illustrates the extendable arm in use, showcasing how it allows for adjustable viewing angles.

How to Use

Constructing the Mount:

1. Unbox all pieces and verify all components are present.
2. Connect the flat piece (likely the base of the arm) into the holes on the back of the mount body and slide up to secure.
3. Screw the joint part (socket) onto the back of the mount body, but initially leave it loose.
4. Leaving the joint loose allows the ball to pop into the socket easily.
5. Once the ball is seated in the socket, tighten the extension knob to secure the position.
6. Peel off the protective plastic film from the suction cup.
7. Place the mount on your dashboard or windshield in your desired location.
8. Squeeze the wings of the clamp to expand it, creating space for your phone.
9. Place your phone into the clamp and press it towards the back of the mount to close the clamps and secure the device.
10. Pull down the lever on the bottom of the stand to ensure the suction is extra secure.
11. To release the phone, squeeze the wings again.

Care and Safety

• Do not use this unit for anything other than its intended purpose.
• Keep the unit away from heat sources, direct sunlight, humidity, water, or any other liquids.
• Do not expose the device to extremely high or low temperatures, as this may damage internal components.
• Do not operate the unit if it has been wet or moist to prevent electric shock or injury, and to avoid damage to the unit.
• Do not use the unit if it has been dropped or damaged in any way.
• Repairs to electrical equipment should only be performed by a qualified professional. Improper repairs may pose a serious risk to the user.
• Keep the unit out of reach of children.
• This unit is not a toy.

Battery Disposal

This product contains a lithium polymer battery. Lithium polymer batteries are environmentally safe when fully discharged. Please refer to your local and state laws for proper battery disposal procedures.

Company Information

OSM TEK GROUP INC, All rights reserved.

BlueStone is a trademark of SM TEK GROUP INC.

New York, NY 10001

Website: www.smtekgroup.com

Made in China