SYNCO XView M4 Mobile Monitor

Thank you for choosing a SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your SYNCO Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping or impact from external force.
• Do not attempt to disassemble the product. Doing so voids the warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions occur.
• Failure to follow all instructions may result in mechanical damage.
• Warranty does not apply to human errors.

Product Introduction

Diagram showing the top view of the SYNCO XView M4 Mobile Monitor. The device has several buttons and ports labeled 1 through 7.

• 1. Bluetooth Shutter / Aspect Ratio Adjustment Button
• 2. Screen Mirror / Rotation Button
• 3. Volume / Brightness + Button
• 4. Volume / Brightness - Button
• 5. Power On/Off Toggle
• 6. TYPE-C Charging Port
• 7. Speaker

Installation

Diagram illustrating the installation process. A magnetic ring is shown being attached to the back of a smartphone. The SYNCO XView M4 Mobile Monitor is then shown aligning with the magnetic ring on the phone.

Operations

1. Charging

Use a Type-C cable to charge the device. (5V=2A)

2. Power On/Off

Power On: Slide the power toggle to the right. Power Off: Slide the power toggle to the left.

Diagram showing the side of the SYNCO XView M4 Mobile Monitor with the power toggle. The toggle is shown in the 'ON' position (slid right) and 'OFF' position (slid left).

3. Phone Pairing

Swipe down from the top-right corner of your phone screen to open the control center.

Diagram showing a smartphone screen with a finger swiping down from the top-right corner to open the control center.

3.1 Screen Projection

(1). Enable the screen projection function (Android: Wireless Projection, iOS: Screen Mirroring) on your phone.

(2). Click to connect the device (SYNCO-XXXX).

3.2 Camera Control

(1). Enable Bluetooth on your phone.

(2). Click to connect the Bluetooth device (SX-XXX).

4. Bluetooth Shooting

Connect your phone via Bluetooth, open the camera, and short press the shutter button to shoot or record.

Diagram illustrating Bluetooth shooting. A phone is connected to the monitor. A finger is shown pressing the shutter button on the monitor with a 'Short Press' label.

5. Aspect Ratio Adjustment

Long press the aspect ratio adjustment button to switch between full-screen and standard aspect ratios.

Diagram illustrating aspect ratio adjustment. A phone is connected to the monitor. A finger is shown pressing the aspect ratio adjustment button with a 'Long Press' label.

6. Screen Mirroring

Short press the mirror button to flip the screen horizontally.

Diagram illustrating screen mirroring. The phone screen content is shown flipping horizontally on the monitor.

7. Screen Rotation

Long press the rotation button to rotate the screen 180° clockwise.

Diagram illustrating screen rotation. The phone screen content is shown rotating 180 degrees clockwise on the monitor.

8. Volume Adjustment

Short press the volume + / - button to increase or decrease the volume (3 levels).

Diagram illustrating volume adjustment. A finger is shown pressing the volume +/- buttons on the monitor with a 'Short Press' label.

9. Brightness Adjustment

Long press the brightness + / - button to increase or decrease brightness (3 levels).

Diagram illustrating brightness adjustment. A finger is shown pressing the brightness +/- buttons on the monitor with a 'Long Press' label.

Specification

Packing List

The packing list includes:

• M4 Mobile Monitor x1
• Magsafe Ring Sticker x1
• Charging Cable x1

Warranty

Warranty Period

Thank you for purchasing SYNCO products.

1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.

Within the warranty period, if a product defect or failure is attributable to material defect or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

Faults resulted from inappropriate use of a product without following its operation specification:

• 1. Artificial damage, e.g., crash, squeeze, scratch, or soaking.
• 2. Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g., replacement of element or circuit, label alteration.
• 3. The code on the product is inconsistent with that of the warranty certificate, or the code on the product or warranty certificate is altered or torn off.
• 4. All consumable accessories attached to a product, like cable, wind muff, battery.
• 5. Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO's customer service through email at support@syncoaudio.com.
2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
3. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.

Contact Information

Guangzhou Zhiying Technology Co., Ltd

Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000

Email: support@syncoaudio.com

Website: www.syncoaudio.com

FCC Compliance Information

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:

Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.