Brook Pocket Auto Catch Reviver Plus User Manual

Product Overview

The Brook Pocket Auto Catch Reviver Plus is an accessory designed to enhance the Pokémon Go gaming experience by automatically catching Pokémon and collecting items from PokéStops.

Model Numbers: ZPP0054, ZPP005T

Part Number: Pocket Auto Catch Reviver Plus

Installation and Removal

Installing the Reviver Plus

1. Insert one end of the Reviver Plus into the slot from the front of the wristband.
2. Press down on the other end with your thumb to push the Reviver Plus into the slot completely.

Removing the Reviver Plus

1. Remove the wristband from your wrist.
2. Hold both ends of the wristband and pull them apart until a small gap is visible between the Reviver Plus and the wristband.
3. Use your finger to pop the Reviver Plus out of its slot from the front side of the wristband.

Charging the Reviver Plus

Connect the Reviver Plus to a USB power source using the provided cable.

• Charging takes approximately 1 hour for a full charge.
• A full charge provides approximately 18 hours of continuous use.
• Standby time is approximately 48 hours.
• When charging, touch the screen to display the charging icon. If the icon does not appear, ensure the Reviver Plus is firmly seated in the charging cable.
• The charging graphic will disappear once fully charged.

Pairing with Your Smartphone

Ensure your smartphone's Bluetooth is turned on.

1. Launch the Pokémon Go app and tap the Main Menu button.
2. Tap 'Settings' at the top right.
3. Select 'Pokémon Go Plus' from the settings page.
4. In the list of available devices, select 'Pokémon Go Plus'.
5. Wait for the pairing process to complete. The Pokémon Go Plus icon turning on indicates successful pairing.

Pairing Troubleshooting

• If pairing fails or the device shows "not paired", go to your phone's Bluetooth settings and remove/clear the 'Pokémon Go Plus' entry.
• In the Pokémon Go game settings, exit/clear 'Pokémon Go Plus'.
• Tap the octagon button on the Reviver Plus. When a new 'Pokémon Go Plus' appears in the game's settings, tap it to pair again.
• If the device has previously paired with another phone, is out of power, or has an abnormality, follow the steps above to reset and re-pair.

Features and Modes

The Reviver Plus can be controlled via the octagon button on its surface.

• Mode Switching: Short press the octagon button to cycle through different modes.
• Mode Activation/Deactivation: Long press the octagon button for 3 seconds to turn a mode ON or OFF.

Catching / Caught Pokémon Status

• Auto-catch Pokémon: ON / OFF
• Auto-catch New Pokémon ONLY: ON / OFF
• New Pokémon discovered
• Duplicate Pokémon found
• Pokémon caught
• Pokémon not caught
• Waiting

Pokéstop Status

• Auto-collect Pokéstop: ON / OFF
• Pokéstop in range
• Pokéstop not in range
• Pokéstop items collected (Indicates quantity: x2, x3, x4, 5+)
• Pokéstop items not collected

Other Alerts and Status

• Vibration alerts: ON / OFF
• Disconnect Vibration: ON / OFF
• Device pairing status: Paired / Not paired
• Battery Capacity Display
• Charging
• Startup Screen
• Out of Pokéballs
• Pokémon is full
• Disconnect

Important Notices

• This product is water resistant.
• Product Liability Insurance is included.
• It is recommended to remove the Pocket Auto Catch Reviver Plus during intense physical activities.
• The product will automatically time out every hour, requiring reconnection within the game.
• Storage Temperature: -20°C to 45°C.
• Optimal Charging Environment: 10°C to 35°C.
• Recommended Smartphone Specifications:
• Requires a smartphone with low-energy Bluetooth connectivity and the Pokémon Go app installed.
• iOS: iPhone 6S or newer, running iOS 12 or higher.
• Android: Devices with 4GB RAM or more, Bluetooth 4.0 or higher, and Android 7.0 or higher.
• This product is not sponsored, endorsed, or produced by Nintendo, The Pokémon Company, or Niantic.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device has been evaluated to meet general RF exposure requirement and can be used in portable exposure conditions without restriction.

Further Information

For the latest user guide and more information, visit Brook's website:

www.brookaccessory.com