Hikvision DS-K2M061 Secure Door Control Unit User Manual
Brand: Hikvision
Product: DS-K2M061 Secure Door Control Unit
Legal Information
©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual
This manual provides instructions for using and managing the Product. Pictures, charts, images, and all other information are for description and explanation purposes only. The information is subject to change without notice due to firmware updates or other reasons. The latest version of this manual can be found on the Hikvision website (https://www.hikvision.com/). It is recommended to use this manual with the guidance and assistance of trained professionals.
Trademarks
HIKVISION and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.
Disclaimer
To the maximum extent permitted by applicable law, this manual and the product described, including its hardware, software, and firmware, are provided "AS IS" and "WITH ALL FAULTS AND ERRORS". Hikvision makes no warranties, express or implied, including without limitation, merchantability, satisfactory quality, or fitness for a particular purpose. The use of the product is at your own risk. Hikvision shall not be liable for any special, consequential, incidental, or indirect damages, including loss of business profits, business interruption, loss of data, system corruption, or loss of documentation, whether based on contract, tort (including negligence), product liability, or otherwise, even if Hikvision has been advised of the possibility of such damages or loss.
Hikvision acknowledges that the internet has inherent security risks. Hikvision shall not be responsible for abnormal operation, privacy leakage, or other damages resulting from cyber-attacks, hacker attacks, virus infections, or other internet security risks. However, Hikvision will provide timely technical support if required.
Users agree to use this product in compliance with all applicable laws and are solely responsible for ensuring their use conforms to the law. This includes not infringing on the rights of third parties, including rights of publicity, intellectual property, or data protection and privacy rights.
This product shall not be used for any prohibited end-uses, including the development or production of weapons of mass destruction, chemical or biological weapons, activities related to nuclear explosive or unsafe nuclear fuel cycles, or in support of human rights abuses.
In the event of any conflicts between this manual and applicable law, the latter prevails.
Data Protection
During device use, personal data will be collected, stored, and processed. Hikvision devices incorporate privacy-by-design principles. For example, devices with facial recognition store biometrics data with encryption, and fingerprint devices save only fingerprint templates, making reconstruction impossible.
As a data controller, users are advised to collect, store, process, and transfer data in accordance with applicable data protection laws and regulations. This includes implementing security controls to safeguard personal data, such as reasonable administrative and physical security controls, and conducting periodic reviews of security control effectiveness.
Safety Instruction
Dangers
- The socket-outlet shall be installed near the equipment and be easily accessible.
- An all-pole mains switch shall be incorporated in the electrical installation of the building.
- Do not connect several devices to one power adapter, as adapter overload may cause overheating or fire hazard.
- If smoke, odors, or noise rise from the device, turn off the power immediately, unplug the power cable, and contact the service center.
- Shock hazard! Disconnect all power sources before maintenance.
- If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (Hikvision assumes no responsibility for problems caused by unauthorized repair or maintenance.)
Cautions
- The equipment is designed for connection to an IT power distribution system when required.
- This equipment is suitable for mounting on concrete or other non-combustible surfaces only.
- The serial port is used for debugging only.
- Install the equipment according to the instructions in this manual.
- To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions.
- No naked flame sources, such as lighted candles, should be placed on the equipment.
- Do not place the device in extremely hot, cold, dusty, or damp locations, or expose it to high electromagnetic radiation. Refer to the device specifications for detailed operating temperature.
- The device cover for indoor use shall be kept from rain and moisture.
- Exposing the equipment to direct sunlight, low ventilation, or heat sources like heaters or radiators is forbidden, as it can cause fire danger.
- Use a soft and dry cloth for cleaning the inside and outside surfaces of the device cover. Do not use alkaline detergents.
- Keep all wrappers after unpacking for future use. In case of any failure, the device may need to be returned to the factory with the original wrapper. Transportation without the original wrapper may result in damage and additional costs.
Available Models
| Product Name | Product Model |
|---|---|
| Secure Door Control Unit | DS-K2M061 |
Chapter 1 Overview
1.1 Product Introduction
Diagram Description (Figure 1-1 Appearance): The diagram shows the physical appearance of the Hikvision DS-K2M061 Secure Door Control Unit. It is a compact device designed to maintain door status in case of access control terminal failure or damage from external force.
The secure door control unit acts as a middle layer between the access control terminal and the door lock within an access control system. The top side connects to the access control terminal, while the bottom side connects to devices such as door contacts, door magnets, exit buttons, and Wiegand card readers. When equipped with access control equipment, it enhances door control security.
1.2 Appearance Introduction
Diagram Description (Figure 1-2 Appearance Description): This section details the physical components of the DS-K2M061 unit through two views (top and side) and a corresponding table.
Components:
- 1. LED Indicator: This indicator serves as the power indicator (POWER). A solid red light signifies that the device is powered on.
- 2. Cable Interface: This is where various cables are connected.
- 3. Debugging Port: A port designated solely for debugging purposes.
- 4. Tamper: A security feature to detect tampering.
- 5. Wiegand Interface: Interface for Wiegand protocol devices, typically card readers.
- 6. DIP Switch: A set of switches used for configuration.
Chapter 2 Interface Description
This chapter describes how to connect access control devices, the secure door control unit, door locks, and other related output devices. It also mentions the option to connect a Wiegand card reader to establish communication.
2.1 Cable Interface Description
Diagram Description (Figure 2-1 Cable Interface Description): This diagram illustrates the various cable connections for the secure door control unit, categorized into groups.
Table 2-1 Cable Interface Description:
| Group No. | Cable No. | Color | Name | Description |
|---|---|---|---|---|
| Group A | A1 | Red | +12 V | Power Input |
| A2 | Black | GND | ||
| Group B | B1 | Yellow | RS-485+ | RS-485 |
| B2 | Blue | RS-485- | ||
| Group C | C1 | Red/Green | FIRE+ | FIRE |
| C2 | Red/Green | FIRE- | ||
| Group D | D1 | Yellow/Blue | ALM_IN1 | Alarm Input |
| D2 | Black | GND | ||
| D3 | Yellow/Orange | ALM_IN2 | ||
| D4 | Black | GND | Alarm Output | |
| D5 | Yellow/Purple | ALM_NC | Alarm Output | |
| D6 | Yellow/Brown | ALM_COM | Alarm Output | |
| D7 | Yellow/Red | ALM_NO | Alarm Output | |
| D8 | Yellow/Green | DOOR_SENSOR | Door Magnetic Input | |
| D9 | Black | GND | Door Contact | |
| D10 | Yellow/Grey | DOOR_BUTTON | Exit Button | |
| D11 | Black | GND | Exit Button | |
| D12 | White/Purple | DOOR_NC | Door Lock Output | |
| D13 | White/Yellow | DOOR_COM | ||
| D14 | White/Red | DOOR_NO |
2.2 Wiegand Interface Description
Diagram Description (Figure 2-2 Wiegand Interface Description): This diagram shows the wiring for the Wiegand interface, typically used with card readers.
Table 2-2 Wiegand Interface Description:
| Group | Cable No. | Color | Name | Description |
|---|---|---|---|---|
| Group E | E1 | Brown | OK | Access Wiegand Card Reader |
| E2 | Purple | BZ | ||
| E3 | Orange | ERR | ||
| E4 | Green | W0 | ||
| E5 | White | W1 | ||
| E6 | Black | GND |
Chapter 3 Wiring Description
Diagram Description (Figure 3-1 External Devices Wiring Description): This diagram illustrates the wiring of external devices to the secure door control unit. It shows connections for Power Input, RS-485, FIRE, Alarm Input, Alarm Output, Door Contact, Exit Button, Door Lock, and Wiegand Card Reader, detailing how each component interfaces with the unit.
Chapter 4 Installation
Before installing the secure door control unit, set the DIP switches and connect the cables.
4.1 DIP Switch Description
Diagram Description (Figure 4-1 DIP Switch Description): The diagram shows the layout of the DIP switches, numbered 1 to 4.
Table 4-1 DIP Switch Meaning:
| Icon | Meaning |
|---|---|
| [switch-state-icon] | Represent 0 in binary mode |
| [switch-state-icon] | Represent 1 in binary mode |
Diagram Description (Figure 4-2 DIP Switch Binary 0011): This figure shows an example of DIP switch settings (1234) representing the binary number 0011, which corresponds to a decimal address of 3.
Notes:
- DIP switch numbers 1 to 3 are used for setting the RS-485 communication address.
- DIP switch number 4 is for Wiegand mode: OFF for Wiegand input, ON for Wiegand output.
- DIP addresses cannot be repeated.
4.2 Install Secure Door Control Unit
Steps:
- Set the DIP switches of the secure door control unit according to the access control device requirements. Note: The DIP binary ranges from 0001 to 1111.
- Drill holes on the wall or other suitable places according to the mounting template. Note: The minimum bearing weight of the wall or mounting surface should be at least three times the device weight.
- Insert the provided plastic sleeve of the A4 expansion screw into the punched hole.
- Insert the cable into the cable socket and the Wiegand cable into the Wiegand interface. Caution: If cables need to be connected from the side of the device, knock out the appropriate knockout hole.
- Align the screw holes on both sides of the device with the sleeves in the wall and secure the device using the provided screws.
Diagram Description (Figure 4-3 Install Secure Door Control Unit): This diagram visually demonstrates the installation process, highlighting the mounting of the unit to a wall and the use of a knockout hole for side cable connections.
Appendix A. Dimension
Diagram Description (Figure A-1 Dimension): This diagram provides the physical dimensions of the DS-K2M061 Secure Door Control Unit. The unit measures 115 mm in height, 48 mm in width, and has a depth of 25.5 mm.
Appendix B. Communication Matrix and Device Command
Communication Matrix: QR codes are provided to access the device communication matrix, which contains all communication ports for Hikvision access control and video intercom devices.
Device Command: QR codes are also provided to access a list of common serial port commands for all Hikvision access control and video intercom devices.
Note: QR codes are excluded from this HTML output as per instructions.
