BlueMarine Reef 350 Aquarium: Setup, Installation, and User Guide
Safety Information
- Read the manual of the stand and accessories carefully before usage.
- Only suitable for indoor use.
- Before filling the aquarium with water, ensure that it is placed on a solid surface that can support the load.
- The aquarium must not be transported in a filled state due to the risk of glass breakage (no warranty coverage).
Parts List
- 1: Transit pipe
- 2: Transit pipe with valve
- 3: Overflow transit with coupling
- 4: Outflow pipe
- 5: Nozzle
- 6: Overflow pipe
- 7: Skimmer
- 8: Pump hose with coupling
- 9: Pump hose connector
- 10: Pump
- 11: Float hose
- 12: Tap of water reservoir
- 13: Float
- 14: ProLED Lighting 2x
- 15: Tank
- 16: Sump
- 17: Water reservoir
- 18: Filter-sock
Installation Guide
Step 1: Placement
Place the aquarium (15) on the cabinet. Ensure the tank is aligned with the cabinet and positioned horizontally to avoid further movement. Verify the aquarium is level.
Step 2: Cabinet Preparation
Remove the cabinet doors. Remove the center pillar by loosening the internal screw and sliding the pillar out. Mount the float (13) in the sump (16). Place the sump into the left compartment of the cabinet, against the back wall.
Step 3: Pipe Installation
Insert the transit pipe (1), outflow pipe (4), and overflow pipe (6) into their designated slots.
Step 4: Connect Transit Pipe
Fit the transit pipe with valve (2) and the overflow transit (3).
Step 5: Pump Assembly
Screw the hose connector (9) into the pump (A). Remove the filter cover (B) from the pump, as it is not required for marine aquariums. Slide the hose (8) onto the hose connector (9).
Step 6: Install Pump
Place the pump (10) in its designated section within the sump.
Step 7: Connect Outflow
Place the nozzle (5) onto the outflow pipe (4). Connect the hose (8) to the outflow pipe (4).
Step 8: Sump Components
Place the filter sock (18) and the skimmer (7) into their respective sections of the sump.
Step 9: Water Reservoir Tap
Assemble the water reservoir tap (12) onto the water reservoir (17). Slide the float hose (11) onto the tap.
Step 10: Connect Float
Place the water reservoir (17) onto the sump. Connect the float hose (11) to the float. The float's position can be adjusted using the adjusting screw (A).
Step 11: Install Lighting
Place the ProLED lighting (14) onto the aquarium and secure it with the screws.
Step 12: Ready for Use
The aquarium is now ready for use.
Step 13: Initial Filling
Open the tap of the transit pipe and fill the tank until the maximum water level is reached in the sump. Observe the "MAX WATER LEVEL" indicator.
Step 14: Fill Reservoir
Fill the water reservoir (17) with osmosis water. Ensure a drip loop is formed in the hose.
Warranty and Recycling Information
Warranty Conditions (GB)
This warranty is valid for 2 years on materials and construction defects. It requires a fully completed warranty slip and an official till receipt with the purchase date. The entire unit with accessories must be supplied for warranty claims. Aquadistri is not liable for glass breakage, damage from negligence, incorrect use, transport, improper setup, or modifications. Claims exceeding the aquarium's value, especially for fish or coral damage, are not covered.
Recycling Information (GB)
The symbol of a barred bin indicates separate collection for electrical and electronic devices. Users must bring the product to a designated collection center at the end of its life or return it to the seller (1-to-1 exchange) when purchasing a new unit. Proper collection is environmentally friendly and aids material recycling; non-compliance is unlawful.
Product Details
Article: REEF 350 ALUMINIUM STAND WHITE / BLACK
Art. nr.: 1007508 / 1007509
Dimensions: 110x60x100 cm
Max Load: 600 kg
Material: Powder coated aluminium frame + 2 aluminium doors
Manufacturer: Produced in China for Aquadistri, www.aquadistri.com
