Tapo T100 Smart Motion Sensor

Meet Your Motion Sensor

The Motion Sensor detects movement in a certain area and triggers different actions in response. This makes your home safer and smarter.

Components: Sensor Detector, LED indicator, Cover, Reset Button, Mounting Stand, Battery Compartment.

Before You Start

A Tapo Hub is required. Ensure your Tapo Hub is successfully added via the Tapo app.

Setup Guide

1. 1. Power Up Your Sensor

   Remove the battery insulation tab to power up your sensor. The LED indicator should blink. If the LED is not blinking, refer to reset instructions.

2. 2. Set Up Your Sensor

   Open the Tapo app. Tap the '+' button, select 'Sensors', then your model. Follow the app instructions to complete setup.

3. 3. Test Your Sensor

   Take your sensor to the preferred location and wave your hand in front of it to test. The Tapo app should indicate if the sensor is triggered.

4. 4. Place Your Sensor

   Choose one of the following mounting options:

   • Option 1: Magnetically attach to metallic objects.
   • Option 2: Stick to a clean wall using the included adhesive.
   • Option 3: Place it on a shelf or table.

Detection Area

Align the sensor with the detection area. Place it as close as possible to the edge of a table or cabinet. The installation height should not exceed 2 meters (approx. 6.5 feet).

The sensor has a detection angle of 120 degrees and a range of up to 7 meters (approx. 23 feet).

How to Replace the Battery

The sensor uses a CR2450 battery.

Option 1: With a Shim

1. Insert a shim into the gap between the cover and the sensor body.
2. Gently pry open the cover.
3. Remove the old battery and insert the new CR2450 battery, observing polarity (+).
4. Replace the cover.

Option 2: By Hand

1. Gently press the cover and slide it off.
2. Remove the old battery and insert the new CR2450 battery, observing polarity (+).
3. Slide the cover back on until it clicks into place.

How to Reset Your Sensor

Use a pin to press and hold the Reset button for 5 seconds until the front LED starts blinking.

Support and Safety Information

Need Help? Visit www.tapo.com/support/ for technical support, user guides, FAQs, warranty information, and more.

Safety Information:

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
• Do not use the device where wireless devices are not allowed.
• Operate the device with care and at your own risk.

Battery Safety Warning (Chemical Burn Hazard):

• This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns in 2 hours and lead to death.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• Seek immediate medical attention if batteries are suspected to have been swallowed or placed inside any part of the body.
• Caution: Avoid replacing the battery with an incorrect type. Avoid disposal of batteries in fire or hot ovens, or mechanical crushing/cutting, as this can result in an explosion. Do not expose batteries to extreme temperatures or low air pressure.

Compliance Information:

For EU/UK Region:

Operating Frequency / Nominal Operating Frequency / Max Output Power:

• 863~865MHz / 863.35MHz / 25mW (e.r.p)
• 863~865MHz / 864.35MHz / 25mW (e.r.p)
• 868~868.6MHz / 868.35MHz / 25mW (e.r.p)

TP-Link declares that the device complies with essential requirements and relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU) 2015/863. The original EU declaration of conformity is available at https://www.tapo.com/en/support/ce/.

TP-Link declares that the device complies with essential requirements and relevant provisions of the Radio Equipment Regulations 2017. The original UK declaration of conformity is available at https://www.tapo.com/support/ukca/.

©2022 TP-Link

Model: Tapo T100

Document Version: REV1.2.1