Tapo Smart Contact Sensor Quick Start Guide

Before You Start

A Tapo Hub is required. Ensure your Tapo Hub is successfully added via the Tapo app.

Download the Tapo app:

• Download on the App Store
• GET IT ON Google Play

For setup videos, scan the QR code or visit: https://www.tp-link.com/support/setup-video/#smart-sensors

Product Components

• Smart Contact Sensor (includes LED Light, Reset Button, Battery Compartment)
• Magnet
• Adhesives (x2)
• Magnet (x1)

Note: Images may differ from actual products.

Setup Instructions

1. Power Up Your Sensor

Remove the battery insulation tab to power up your sensor. The LED should begin to blink.

Note: If the LED is not blinking, refer to the reset instructions.

2. Set Up Your Sensor

Open the Tapo app, tap the '+' button within the app, and select your sensor model. Follow the app instructions to complete the setup.

3. Test Your Sensor

a. Open and close the sensor to test its functionality in your desired location.

b. Check the Event Log on the Tapo app to confirm the open/closed status updates.

4. Mount Your Sensor

a. Apply the included adhesives to the sensor and the magnet.

b. Choose the installation location. Place the magnet on the edge of the door or window that moves. The installation height should not exceed 6.56 ft (2 m).

c. Align the magnet and sensor. Ensure there is no more than 0.59 inches (15 mm) gap between them when the door or window is closed. Maintain at least 0.39 inches (10 mm) space to allow for battery compartment access.

d. Peel the backing from the adhesives and press the sensor and magnet firmly into place.

How to Reset Your Sensor to Enter Pairing Mode

a. Slide to remove the cover of your sensor.

b. Use a pin or similar pointed object to press and hold the Reset button for 5 seconds until the front LED starts blinking.

How to Replace the Battery

a. Remove the sensor cover. Use a screwdriver to open the battery cover.

b. Replace the battery with a fresh CR2032 cell, ensuring correct polarity (+ and -).

Support

For technical support, user guides, warranty information, and more, please visit: https://www.tapo.com/support/

Safety Information

❗ WARNING: Ingestion Hazard

• This product contains a button cell or coin battery.
• Swallowing a battery can cause severe internal chemical burns in as little as 2 hours and can lead to death.
• Keep new and used batteries OUT OF REACH of CHILDREN.
• Seek immediate medical attention if a battery is suspected to have been swallowed or inserted inside any part of the body.

Explanation of Symbols:

Warning! This product contains a button cell or coin battery. Avoid ingestion hazard. Death or serious injury can occur if ingested.

CAUTION! Risk of explosion if the battery is replaced by an incorrect type.

CAUTION! Avoid replacement of a battery with an incorrect type that can defeat a safeguard. Do not dispose of batteries in fire or a hot oven, or mechanically crush or cut them, as this can result in an explosion. Do not leave batteries in extremely high temperatures or low air pressure environments, as this may result in an explosion or leakage.

CAUTION: Do not ingest battery, Chemical Burn Hazard

• If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you suspect batteries have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep them away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• This product uses button/coin cell batteries of type CR2032.
• The nominal voltage is +3V.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above 60°C/140°F, or incinerate batteries. Doing so may result in injury due to venting, leakage, or explosion, leading to chemical burns.
• Ensure batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, or different brands or types of batteries (e.g., alkaline, carbon-zinc, rechargeable).
• Remove batteries from equipment not used for extended periods.
• Always secure the battery compartment completely. If it does not close securely, stop using the product, remove batteries, and keep them away from children.

General Safety:

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
• Do not use the device where wireless devices are not allowed.

Please read and follow the safety information. TP-Link cannot guarantee against accidents or damage due to improper use. Use this product with care and at your own risk.

Compliance Information

TP-Link declares that this device complies with essential requirements and other provisions of directives 2014/53/EU, 2011/65/EU, and (EU) 2015/863. The original EU declaration of conformity can be found at: https://www.tapo.com/en/support/ce/

TP-Link declares that this device complies with the essential requirements and other provisions of the Radio Equipment Regulations 2017. The original UK declaration of conformity can be found at: https://www.tapo.com/support/ukca/

For EU/UK Region:

Operating Frequency / Nominal Operating Frequency / Max Output Power:

• 863~865MHz / 863.35MHz / 25mW (e.r.p)
• 863~865MHz / 864.35MHz / 25mW (e.r.p)
• 868~868.6MHz / 868.35MHz / 25mW (e.r.p)

©2024 TP-Link