Style Selections Kenwood Dining Chairs

Table of Contents

• Package Contents
• Hardware Contents
• Safety Information
• Preparation
• Assembly Instructions
• Care and Maintenance
• Troubleshooting
• Warranty
• Replacement Parts List

Package Contents

The package contains the following parts:

• Right Armrest (A) - 6 pcs
• Left Armrest (B) - 6 pcs
• Seat Frame (C) - 6 pcs
• Backrest (D) - 6 pcs
• Seat Cushions (E) - 6 pcs

Visual Description: Six identical dining chairs are shown. Each chair features a woven seat and back, with a distinct armrest design.

Hardware Contents

The hardware package includes:

• M6 x 30 mm Bolt (AA) - 24 + 2 Extra pcs
• M6 x 35 mm Bolt (BB) - 12 + 2 Extra pcs
• M6 x 55 mm Bolt (CC) - 24 + 2 Extra pcs
• Metal Washer (DD) - 48 + 4 pcs
• Ratchet (EE) - 2 pcs (Not actual size)

Visual Description: Illustrations of the bolts, washers, and ratchet tool are provided, with quantities indicated.

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

• Assembly requires one or two people.
• Load capacity per seat: 250 lbs (113.39 kg).

WARNING:

• Always place cushions on the seat frame to avoid damage.
• Small parts like washers can pose a choking hazard to young children. Keep out of reach of children.

CAUTION:

• Assemble on a soft, non-abrasive surface (e.g., carpet or cardboard) to prevent damage.
• Ensure all bolts are securely tightened after final alignment.
• Remove all parts from the carton and protective material. Identify all parts against the parts list.
• Do not tighten bolts until the product is completely assembled.
• Do not use power tools for assembly.

Preparation

Before beginning assembly, ensure all parts are present. Compare parts with the package and hardware lists. Do not attempt assembly if any part is missing or damaged.

Estimated Assembly Time: Approximately 15 minutes per chair.

Assembly Instructions

1. Secure the front of the seat frame (C) to the right armrest (A) using one M6 x 35 mm Bolt (BB) and one Metal Washer (DD) with the ratchet (EE). Then, secure the seat frame (C) to the right armrest (A) using two M6 x 30 mm Bolts (AA) and two Metal Washers (DD) with the ratchet (EE).

   DO NOT tighten all bolts at this step.

   Visual Description: Diagram shows attaching the seat frame to the right armrest using specified hardware.

2. Secure the bottom of the backrest (D) to the right armrest (A) using two M6 x 55 mm Bolts (CC) and two Metal Washers (DD) with the ratchet (EE). Then, secure the right armrest (A) to the backrest (D) using one M6 x 55 mm Bolt (CC) with the ratchet (EE).

   DO NOT tighten all bolts at this step.

   Visual Description: Diagram illustrates attaching the backrest to the right armrest using specified hardware.

3. Secure the front of the seat frame (C) to the left armrest (B) using one M6 x 35 mm Bolt (BB) and one Metal Washer (DD) with the ratchet (EE). Then, secure the seat frame (C) to the left armrest (B) using two M6 x 30 mm Bolts (AA) and two Metal Washers (DD) with the ratchet (EE).

   DO NOT tighten all bolts at this step.

   Visual Description: Diagram shows attaching the seat frame to the left armrest using specified hardware.

4. Secure the bottom of the backrest (D) to the leg of the left armrest (B) using two M6 x 55 mm Bolts (CC) and two Metal Washers (DD) with the ratchet (EE). Repeat this step for the other side of the backrest (D). Secure the seat frame (C) to the backrest (D) using one M6 x 35 mm Bolt (BB) and one Metal Washer (DD) with the ratchet (EE).

   Tighten all bolts at this step.

   Visual Description: Diagram illustrates attaching the backrest to the left armrest and then securing the seat frame to the backrest.

5. Turn over the assembled chair and place the seat cushion (E) on it. Repeat the assembly process for the remaining five chairs.

   Visual Description: Image shows placing the seat cushion onto the assembled chair.

Care and Maintenance

• Never allow water to build up in frames, as this can cause corrosion and freeze damage in cold climates.
• Wash cushions with a solution of mild soap and water. Rinse with clean water and dry with a soft absorbent cloth. Never machine wash cushions, as this may cause shrinkage or damage.
• After cleaning, tip cushions on end to dry. Do not use a commercial or home dryer.
• The frame can be treated with a liquid wax for maximum protection against UV rays and salty damp air.
• Do not use bleach or solvents to clean any product, as this will void the warranty.

Troubleshooting

Warranty

This warranty extends to the original purchaser and applies to defects in materials and workmanship, provided the item is maintained with care and used for personal, residential purposes only.

The frame and fabric are warranted for two years against defects in material or workmanship. Products used for commercial, contract, or other non-residential purposes, display models, and clearance items are not covered.

The warranty does not cover damage caused by shipping, acts of nature, fire, abuse, vandalism, lack of proper care and maintenance, fading cushions and coatings, hardware corrosion and rust, freezing, or improper assembly.

The manufacturer is not liable for any direct, indirect, incidental, or consequential damages. Style Selections reserves the right to substitute similar quality merchandise if the model in question is out of stock.

Warranty covers free replacement within two years of purchase. After two years, the customer will pay for freight for replacement items.

This warranty grants specific legal rights, and other rights may vary by state. For warranty service, contact 877-888-8225.

Replacement Parts List

For replacement parts, contact customer service at 877-888-8225 (8 a.m. - 8 p.m. EST, Monday - Sunday) or ascs@lowes.com.

Visual Description: Illustrations of each part (A-E, AA-EE) are provided for identification.

Printed in China