BOSS Audio MGR450B Bluetooth Marine Gauge Receiver

Introduction

Thank you for purchasing the BOSS AUDIO SYSTEMS MGR450B Bluetooth Marine Gauge Digital Media AM/FM Receiver. This guide provides instructions for proper operation and installation. Please read these instructions carefully and keep them for future reference.

Package Contents

• MGR450B Receiver (1pc)
• Metal Bracket (1pc)
• Hexagon Mounting Studs (2pcs)
• Machine Screws (4pcs)
• M4 Secure Nuts (4pcs)
• User Manual (1pc)
• Warranty Card (1pc)

Important Safety Precautions

• Do not operate the volume so high that you cannot hear your surroundings.
• Use caution in potentially hazardous situations.
• Do not operate while driving; prioritize safe driving.
• Set volume to a comfortable, low level and increase slowly.
• If you notice smoke, strange noises, or odors, turn off the power immediately and consult a dealer or service center.

Installation Precautions

• Consult a professional installer for installation.
• Do not attempt self-installation or servicing.
• Refer repairs to a qualified BOSS AUDIO SYSTEMS Service Center.
• Wire directly to the vehicle's battery. Disconnect the negative terminal before wiring.
• If extending the main power wire, use an optional 20 Ampere fuse and fuse holder.
• Keep the ground cable short and use high-quality copper wire.
• The MGR450B is IPX6 weather-resistant; do not submerge it in water.
• Do not use abrasive cleaning materials on the lens or bezel.
• Use only provided installation parts.
• Caution: Disconnect the (-) battery cable before installation to avoid shorts. Use only with a 12-Volt battery and negative grounding.
• When replacing the fuse, use only the specified rating (15A AGU type). Insulate all unused wires.
• Connect the black ground wire first. Ensure it is properly connected to the vehicle's metal frame or battery.
• Ground the power amp and other systems separately.
• Caution: Do not ground or short the speaker leads.

Mounting Methods

1. Make the mounting hole: 3.00" (76mm) diameter.
2. Install studs into the rear of the chassis. Adjust M4 nuts for mounting depth. Snap off break-away tabs as needed.
3. Slip the unit through the hole cutout and into the U-bracket.
4. Secure and waterproof the wiring.
5. Firmly tighten the remaining M4 nuts.

Tools Needed: Measuring Tape/Ruler, Wrench/Pliers, Hole Saw, Crimp Tool.

Wire Diagram

Accessory (+12V): Red
Ground (-): Black
Left Rear Speaker (-): Green/Black
Left Front Speaker (-): White/Black
Left Rear Speaker (+): Green
Left Front Speaker (+): White
Right Front Speaker (-): Gray/Black
Right Rear Speaker (-): Purple/Black
Amp Remote (+12V): Blue
Right Rear Speaker (+): Purple
Right Front Speaker (+): Gray
Antenna: White
USB: Red (Right), White (Left)
Aux-In: Yellow
Subwoofer: Red (Right), White (Left)
Rear Line Out: Red (Right), White (Left)
Front Line Out: Grey
Remote Port: White

For Charging Only (USB): Cell Phone and iPod Media Playback Not Supported. USB Output Voltage: 5VDC @ 1A.

Specifications

• FM Tuner Frequency Range: USA 87.5~107.9MHz, Europe/Asia/Australia 87.5~108MHz
• AM Tuner Frequency Range: USA 530~1710KHz, Europe/Asia/Australia 522~1620KHz
• Integrated Amplifier: MOSFET, MAX Continuous Output 240W, PEAK Power 60W/channel, Class AB, Frequency Response 20-20kHz, 4Ω stable
• Chassis: Button Backlight Illumination: BLUE LED, F/R/S RCA Preamp Output: 2VRMS, RCA Input Impedance: 10kΩ
• Bluetooth: BT 3.0, Range 33Ft/10M (Class 2), Profiles: A2DP/AVRCP 1.3
• Weather Band Selection: CH.1-CH.7 frequencies listed.
• USB Drive Media Support: MP3, WMA, up to 65,000 Songs, 32GB/FAT32, USB 2.0 High Speed
• General: Power Source 14.4VDC (10.8V~16V allowable), Negative Grounding System, Max Current Consumption 15A, 3-way protection circuitry, Unit Weight 1.08lbs/0.52kg, Storage Temp -22°F to 176°F, Operation Temp -4°F to 158°F.
• Replacement Fuse: 15A (AGU Fuse Type Only)

Troubleshooting

Technical Support

Phone: 1-805-751-4853

Website: www.bossaudio.com/support

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operated with any other antenna or transmitter. The Bluetooth antenna cannot be removed or replaced by the user. This equipment complies with FCC/IC radiation exposure limits for an uncontrolled environment. Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. If interference occurs, try relocating the antenna, increasing separation, connecting to a different outlet, or consulting a dealer/technician.

WARNING: Adjustment or alterations of this device may result in hazardous radiation exposure.

Legal Information

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Use of these marks by BOSS Audio Systems is under license. Other trademarks and trade names are those of their respective owners.

FCC ID: 2AB7S-MGR450B