Forte F24DWS650PR Dishwasher Installation Guide
Product Overview
This document provides detailed instructions for the installation of the Forte F24DWS650PR 24-inch Panel Ready Built-In Fully Integrated Dishwasher.
Model Number: F24DWS650PR
Part Reference: WOR12 6507
Part Number: 16176000A65490
Required Installation Space
Ensure the cabinet opening meets the following dimensions:
- Width: 23.19 - 23.23 inches (589MM)
- Height (X): 28.3 - 28.4 inches
- Height (Y): 23.2 - 23.3 inches
- Depth (Z): 0.63 inches
Maximum load capacity for mounting: 13.228 lbs.
Clearance requirement: Max 1.181 inch.
Parts Included
| Part Number | Description | Quantity |
|---|---|---|
| 1 | ST4X14 Screws | 8 |
| 2 | ST3.5X25 Screws | 2 |
| 3 | ST4X30 Screws | 2 |
| 4 | ST3.5X45 Screws | 4 |
| 5 | Component | 1 |
| 6 | ST3.5X16 Screws | 2 |
| 7 | Component | 2 |
| 8 | Component | 2 |
| 9 | Component | 2 |
| 10 | Component | 6 |
| 11 | ST4X14 Screws | 4 |
| 12 | Component | 2 |
| 13 | Component | 4 |
| 14 | Component | 4 |
| 15 | Component | 1 |
| 16 | Component | 2 |
| 17 | Component | 2 |
| 18 | Component | 1 |
| 19 | Component | 2 |
| 20 | Component | 2 |
| 21 | Component | 1 |
| 22 | Component | 2 |
Installation Steps
- Prepare Cabinet (Left Side):
On the left side of the cabinet opening, drill pilot holes for mounting brackets. Use the provided [installation template] for precise placement. Attach two mounting brackets using specified screws (e.g., Part 1: ST4X14 screws).
Diagrams show measurements for hole positioning and bracket placement.
- Attach Dishwasher (Left Side):
Slide the dishwasher unit into the cabinet opening. Align it with the mounted brackets. Secure the unit to the brackets using appropriate screws.
- Prepare Cabinet (Right Side):
Repeat the process for the right side of the cabinet opening. Drill pilot holes and attach two mounting brackets using specified screws.
- Attach Dishwasher (Right Side):
Slide the dishwasher unit into the cabinet opening from the right side and secure it to the right-side brackets.
- Adjust Height and Leveling:
Use the adjustment screws located at the bottom or top of the unit to level the dishwasher and achieve the desired height. The diagram shows adjustment screws and indicates directions for adjustment ([down arrow]/[up arrow]).
Measurement shown: 2.0 [down/up adjustment].
- Final Securing:
Ensure the dishwasher is firmly secured in place. The diagrams show final fastening steps, potentially using screws like 4*15 and 4*20, and may involve angled securing points (approximately [angle symbol]45 degrees).
- Water Connection:
Connect the water supply line to the dishwasher. The diagram indicates a connection point with a pressure rating of 0.05-1MPa and a thread size of 1.04 inch (G3/4").
- Drainage Connection:
Connect the dishwasher's drain hose to the household plumbing according to local codes.
- Electrical Connection:
Connect the dishwasher to the power supply. Refer to the separate electrical connection diagram or manual for specific instructions.
- Panel Installation:
Attach the custom front panel to the dishwasher door according to the panel's specific mounting instructions.
- Final Checks:
Verify all connections are secure and the dishwasher is level. Test the unit for proper operation.
Diagrams show specific measurements for panel alignment (e.g., 23.5 inches, 21.47 inches) and component placement.
Important Notes
- Always follow local building and electrical codes.
- Ensure proper grounding for electrical connections.
- Refer to the main user manual for operating instructions.
