CAT 1:24RC 336 Hydraulic Excavator

Contents

• RC Vehicle (Vehicle) x 1
• RC Transmitter (Transmitter) x 1
• Instruction Manual x 1

Included Components: RC Transmitter (Transmitter) x 1, RC Vehicle (Vehicle) x 1

Battery Requirements: 2 x AAA for Transmitter (Not Included), 5 x AA for Vehicle (Not Included)

Battery Precaution

1. Alkaline batteries are recommended for use.
2. Only batteries of the same or equivalent type as recommended should be used.
3. Do not mix alkaline, standard, or rechargeable batteries.
4. Do not mix old and new batteries or different types of batteries.
5. Non-rechargeable batteries are not to be charged.
6. Rechargeable batteries are for adult charging only.
7. Rechargeable batteries must be removed from the product before they are charged.
8. Ensure batteries are inserted with correct polarities (Positive [+] and Negative [-]) and always follow the battery manufacturer's instructions.
9. Remove all batteries from the Vehicle and Transmitter when not in use.
10. Exhausted batteries must be removed from the product.
11. The supply terminals are not to be short-circuited.
12. Dispose of batteries properly. Do not dispose of batteries in fire, as it may cause them to explode or leak, leading to injury or damage.
13. Battery installation and removal must only be performed by an adult.

Battery Installation

For Vehicle (Refer to Figure 1 and Figure 2)

Figure 1 shows the location of the battery cover on the vehicle. Figure 2 illustrates the correct placement of 5 AA batteries within the vehicle's battery compartment, indicating positive (+) and negative (-) terminals.

1. Switch the power OFF.
2. Unscrew the screw securing the battery cover.
3. Open the battery cover.
4. Install 5 new 1.5V AA batteries, ensuring correct polarities (+/-) as indicated inside the battery compartment.
5. Close the battery cover.
6. Tighten the screw on the battery cover.

For Transmitter (Refer to Figure 3 and Figure 4)

Figure 3 shows the battery cover on the transmitter. Figure 4 illustrates the correct placement of 2 AAA batteries within the transmitter's battery compartment, indicating positive (+) and negative (-) terminals.

1. Unscrew the screw securing the battery cover.
2. Open the battery cover.
3. Install 2 new 1.5V "AAA" batteries, ensuring correct polarities (+/-) as indicated inside the battery compartment.
4. Close the battery cover.
5. Tighten the screw on the battery cover.

How to Bind

1. Turn on the Vehicle.
2. Install batteries in the Transmitter. The Transmitter's signal light will flash for a few seconds.
3. The binding process is complete for playing when the Vehicle's wheels turn left and right, and the LED light on the Transmitter stops flashing.
4. If binding does not complete within 8 seconds, turn off the Vehicle and restart the binding process.
5. Once bound, the Vehicle searches for its memorized code when switched on and will only lock onto the Transmitter signal containing that code.
6. Turn off the Vehicle and restart the binding process if you are changing to another 2.4GHz Transmitter for playing.
7. Do not attempt 2.4GHz frequency signal pairing for the vehicle and transmitter near other 2.4GHz remote-controlled products, as this can cause interference or loss of control.

How To Play

Ensure the Vehicle is switched ON using the power switch.

Controls:

• Left/Right Joystick: Use the Left/Right joystick to control the Vehicle's turning direction (left or right).
• Forward/Backward Joystick: Use the Forward/Backward joystick to drive the Vehicle Forward, Stop, or move Backward.
• Bucket Up Button: Press the Bucket move up button to raise the excavator's bucket.
• Bucket Down Button: Press the Bucket move down button to lower the excavator's bucket.

Direction Adjustment: If the Vehicle does not drive in a straight line, adjust the direction adjustment control located on the Vehicle chassis (refer to Figure 1 for its approximate location).

Playing Surface: Play on a smooth surface for optimum performance.

Power Off: Remember to switch OFF the power of the Vehicle after playing to conserve battery and prevent damage.

Control Range: The optimum control range is up to 25 meters (82 feet) outdoors.

Performance Tips

1. Do not drive the vehicle on grass, dirt, sand, dust, carpet, or through water.
2. Do not operate in windy or rainy weather.
3. Avoid direct impact with obstacles.
4. Switch OFF the power when the vehicle is not in use to prevent damage from battery leakage.
5. Remove all batteries from the Vehicle and Transmitter if they will not be used for a long period.
6. Keep fingers, hair, and loose clothing away from the vehicle's wheels.
7. The operating range can be affected by several factors, including:
• Low battery voltage in the Transmitter or Vehicle.
• Interference from other devices emitting radio frequency signals.
8. Outdoor usage is recommended to achieve the optimum control range.
9. It is recommended to play with the vehicle on a clean and smooth surface.
10. Clean the battery compartment to ensure it is free from dust, which can prevent proper battery contact.

Cautions and Safety Information

1. Do not attempt to disassemble the Vehicle or Transmitter.
2. Ensure batteries are installed with correct polarities (+/-) as indicated inside the battery compartment.
3. Remove all packaging and accessories before giving the Vehicle and Transmitter to a child to play with.

The packaging and instruction manual contain important information. Please keep them for future reference.

Warning: Choking Hazard. Not suitable for children under 3 years of age due to small parts.

Specifications and colors are subject to change without prior notice.

Warning: The antenna of the vehicle and/or transmitter must not be inserted into socket outlets.

Compliance and Regulatory Information

FCC Label Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RSS-210 Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of Conformity

The product is in conformity with the requirement of EU Directive 2014/53/EU.

Environmental Notes

The product should not be disposed of as household waste at the end of its life. Return it to collection points for the recycling of electronic and electrical instruments. The symbol on the item, instruction manual, hangtag, or packaging indicates this clearly. Materials should be recycled according to their respective markings. Recycling old devices or reusing materials contributes to environmental protection. Please ask your local community for the correct collection point.

Disposal of Batteries

Batteries should not be disposed of in household waste. Consumers are legally obliged to return batteries containing harmful substances and all other used batteries. Hand in old batteries at public collection points or wherever batteries are sold. Chemical abbreviations for harmful substances found on batteries include:

• Pb: Battery contains lead
• Cd: Battery contains cadmium
• Hg: Battery contains mercury

Product Safety Compliance: Product must be assembled by adult only. Conforms to the safety requirements of ASTM F963.

Radio Frequency Information: Frequency band: 2405-2475 MHz. Maximum radio frequency power transmitted: <0 dBm.

Manufacturer/Licensor Information: © 2020 Caterpillar. CAT, CATERPILLAR, their respective logos, "Caterpillar Yellow," and "Power Edge" trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. Diecast Masters Company Limited, a licensee of Caterpillar Inc. © 2020 Diecast Masters Company Limited, Room 1801-5, 18/F King Palace Plaza, 52A Sha Tsui Road, Tsuen Wan, N.T., Hong Kong. Visit www.cat.com / www.caterpillar.com or www.diecastmasters.com.